dev: full project reflectometer

Reviewed-on: #7

constraints/ax7a035b.xdc

@@ -59,39 +59,80 @@ set_property SLEW FAST [get_ports {rgmii_txd[*]}]
 create_clock -period 8.000 [get_ports rgmii_rxc]
 
 # === DAC (J11 header) ===
-set_property IOSTANDARD LVCMOS33 [get_ports p2_clk]
+#set_property IOSTANDARD LVCMOS33 [get_ports p2_clk]
-set_property IOSTANDARD LVCMOS33 [get_ports p2_wrt]
+#set_property IOSTANDARD LVCMOS33 [get_ports p2_wrt]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[13]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[13]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[12]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[12]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[11]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[11]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[10]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[10]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[9]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[9]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[8]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[8]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[7]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[7]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[6]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[6]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[5]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[5]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[4]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[4]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[3]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[3]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[2]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[2]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[1]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[1]}]
-set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[0]}]
+#set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[0]}]
 
-set_property SLEW FAST [get_ports p2_clk]
+#set_property SLEW FAST [get_ports p2_clk]
 
-set_property PACKAGE_PIN C18 [get_ports p2_clk]
+#set_property PACKAGE_PIN C18 [get_ports p2_clk]
-set_property PACKAGE_PIN C19 [get_ports p2_wrt]
+#set_property PACKAGE_PIN C19 [get_ports p2_wrt]
-set_property PACKAGE_PIN B17 [get_ports {p2_data[13]}]
+#set_property PACKAGE_PIN B17 [get_ports {p2_data[13]}]
-set_property PACKAGE_PIN B18 [get_ports {p2_data[12]}]
+#set_property PACKAGE_PIN B18 [get_ports {p2_data[12]}]
-set_property PACKAGE_PIN D17 [get_ports {p2_data[11]}]
+#set_property PACKAGE_PIN D17 [get_ports {p2_data[11]}]
-set_property PACKAGE_PIN C17 [get_ports {p2_data[10]}]
+#set_property PACKAGE_PIN C17 [get_ports {p2_data[10]}]
-set_property PACKAGE_PIN A15 [get_ports {p2_data[9]}]
+#set_property PACKAGE_PIN A15 [get_ports {p2_data[9]}]
-set_property PACKAGE_PIN A16 [get_ports {p2_data[8]}]
+#set_property PACKAGE_PIN A16 [get_ports {p2_data[8]}]
-set_property PACKAGE_PIN B15 [get_ports {p2_data[7]}]
+#set_property PACKAGE_PIN B15 [get_ports {p2_data[7]}]
-set_property PACKAGE_PIN B16 [get_ports {p2_data[6]}]
+#set_property PACKAGE_PIN B16 [get_ports {p2_data[6]}]
-set_property PACKAGE_PIN A13 [get_ports {p2_data[5]}]
+#set_property PACKAGE_PIN A13 [get_ports {p2_data[5]}]
-set_property PACKAGE_PIN A14 [get_ports {p2_data[4]}]
+#set_property PACKAGE_PIN A14 [get_ports {p2_data[4]}]
-set_property PACKAGE_PIN E16 [get_ports {p2_data[3]}]
+#set_property PACKAGE_PIN E16 [get_ports {p2_data[3]}]
-set_property PACKAGE_PIN D16 [get_ports {p2_data[2]}]
+#set_property PACKAGE_PIN D16 [get_ports {p2_data[2]}]
-set_property PACKAGE_PIN C14 [get_ports {p2_data[1]}]
+#set_property PACKAGE_PIN C14 [get_ports {p2_data[1]}]
-set_property PACKAGE_PIN C15 [get_ports {p2_data[0]}]
+#set_property PACKAGE_PIN C15 [get_ports {p2_data[0]}]
+
+# === ADC an9238 (J11 header) ===
+set_property PACKAGE_PIN G21 [get_ports ch2_clk]
+set_property PACKAGE_PIN G22 [get_ports ch2_data[0]]
+set_property PACKAGE_PIN C22 [get_ports ch2_data[1]]
+set_property PACKAGE_PIN B22 [get_ports ch2_data[2]]
+set_property PACKAGE_PIN F19 [get_ports ch2_data[3]]
+set_property PACKAGE_PIN F20 [get_ports ch2_data[4]]
+set_property PACKAGE_PIN D20 [get_ports ch2_data[5]]
+set_property PACKAGE_PIN C20 [get_ports ch2_data[6]]
+set_property PACKAGE_PIN A18 [get_ports ch2_data[7]]
+set_property PACKAGE_PIN A19 [get_ports ch2_data[8]]
+set_property PACKAGE_PIN B20 [get_ports ch2_data[9]]
+set_property PACKAGE_PIN A20 [get_ports ch2_data[10]]
+set_property PACKAGE_PIN F18 [get_ports ch2_data[11]]
+set_property PACKAGE_PIN E18 [get_ports ch2_otr]
+set_property PACKAGE_PIN C18 [get_ports ch1_data[1]]
+set_property PACKAGE_PIN C19 [get_ports ch1_data[0]]
+set_property PACKAGE_PIN B17 [get_ports ch1_data[3]]
+set_property PACKAGE_PIN B18 [get_ports ch1_data[2]]
+set_property PACKAGE_PIN D17 [get_ports ch1_data[5]]
+set_property PACKAGE_PIN C17 [get_ports ch1_data[4]]
+set_property PACKAGE_PIN A15 [get_ports ch1_data[7]]
+set_property PACKAGE_PIN A16 [get_ports ch1_data[6]]
+set_property PACKAGE_PIN B15 [get_ports ch1_data[9]]
+set_property PACKAGE_PIN B16 [get_ports ch1_data[8]]
+set_property PACKAGE_PIN A13 [get_ports ch1_data[11]]
+set_property PACKAGE_PIN A14 [get_ports ch1_data[10]]
+set_property PACKAGE_PIN E16 [get_ports ch1_clk]
+set_property PACKAGE_PIN D16 [get_ports ch1_otr]
+
+set_property IOSTANDARD LVCMOS33 [get_ports ch2_clk]
+set_property IOSTANDARD LVCMOS33 [get_ports {ch2_data[*]}]
+set_property IOSTANDARD LVCMOS33 [get_ports ch2_otr]
+set_property IOSTANDARD LVCMOS33 [get_ports {ch1_data[*]}]
+set_property IOSTANDARD LVCMOS33 [get_ports ch1_clk]
+set_property IOSTANDARD LVCMOS33 [get_ports ch1_otr]
+
+# 1 bit DAC)))
+set_property PACKAGE_PIN E17 [get_ports debug_dac]
+set_property IOSTANDARD LVCMOS33 [get_ports debug_dac]
 

designs/reflectometer/Makefile

@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = reflectometer_top
+FPGA_ARCH = artix7
+
+RTL_DIR = ../../rtl
+
+
+include ../../scripts/vivado.mk
+
+SYN_FILES += reflectometer.sv
+SYN_FILES += $(sort $(shell find ../../rtl -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../../rtl/ethernet-udp/src -type f -name '*.xci'))
+XCI_FILES += $(sort $(shell find ip/ -type f -name '*.xci'))
+
+XDC_FILES += ../../constraints/ax7a035b.xdc
+XDC_FILES += debug.xdc
+
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

designs/reflectometer/README.md

@@ -0,0 +1,11 @@
+# Тестовый проект Generator + ETH + CTRL
+Проект состоит из AXIS Ethernet, контроллера и генератора. Позволяет генерировать сигналы, задав параметры через Ethernet.
+## Сборка
+```make all``` - собрать все до битстрима
+
+```make vivado``` - открыть проект в Vivado
+
+## Управление
+Используйте software/console.py. Пример:
+
+```python3 console.py --pulse_width 3_500_000 --pulse_period 20_000_000 --pulse_height 10000 --pulse_num 5500 --dac-bits 14```

designs/reflectometer/debug.xdc

@@ -0,0 +1,2 @@
+set_clock_groups -name ASYNC_UDP_CTRL -asynchronous -group [get_clocks rgmii_rxc] -group [get_clocks clk_out1_clk_wiz_ctrl_inst] -group [get_clocks clk_out2_clk_wiz_ctrl_inst]
+

designs/reflectometer/ip/clk_wiz_ctrl_inst.xci

@@ -0,0 +1,689 @@
+{
+  "schema": "xilinx.com:schema:json_instance:1.0",
+  "ip_inst": {
+    "xci_name": "clk_wiz_ctrl_inst",
+    "component_reference": "xilinx.com:ip:clk_wiz:6.0",
+    "ip_revision": "16",
+    "gen_directory": "../../../../eth_generator_top.gen/sources_1/ip/clk_wiz_ctrl_inst",
+    "parameters": {
+      "component_parameters": {
+        "Component_Name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "user", "usage": "all" } ],
+        "USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "ENABLE_CLOCK_MONITOR": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK2": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK3": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRECISION": [ { "value": "1", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "PRIMTYPE_SEL": [ { "value": "mmcm_adv", "resolve_type": "user", "usage": "all" } ],
+        "CLOCK_MGR_TYPE": [ { "value": "auto", "resolve_type": "user", "usage": "all" } ],
+        "USE_FREQ_SYNTH": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_SPREAD_SPECTRUM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_PHASE_ALIGNMENT": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_POWER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_PHASE_SHIFT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_RECONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "user", "usage": "all" } ],
+        "PRIM_IN_FREQ": [ { "value": "200.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "user", "usage": "all" } ],
+        "PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "user", "usage": "all" } ],
+        "IN_JITTER_UNITS": [ { "value": "Units_UI", "resolve_type": "user", "usage": "all" } ],
+        "RELATIVE_INCLK": [ { "value": "REL_PRIMARY", "resolve_type": "user", "usage": "all" } ],
+        "USE_INCLK_SWITCHOVER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "user", "usage": "all" } ],
+        "SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "JITTER_OPTIONS": [ { "value": "UI", "resolve_type": "user", "usage": "all" } ],
+        "CLKIN1_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN1_JITTER_PS": [ { "value": "50.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_USED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_USED": [ { "value": "true", "value_src": "user", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "NUM_OUT_CLKS": [ { "value": "2", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLK_OUT1_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT2_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT3_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT4_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT5_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT6_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT7_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "user", "usage": "all" } ],
+        "DADDR_PORT": [ { "value": "daddr", "resolve_type": "user", "usage": "all" } ],
+        "DCLK_PORT": [ { "value": "dclk", "resolve_type": "user", "usage": "all" } ],
+        "DRDY_PORT": [ { "value": "drdy", "resolve_type": "user", "usage": "all" } ],
+        "DWE_PORT": [ { "value": "dwe", "resolve_type": "user", "usage": "all" } ],
+        "DIN_PORT": [ { "value": "din", "resolve_type": "user", "usage": "all" } ],
+        "DOUT_PORT": [ { "value": "dout", "resolve_type": "user", "usage": "all" } ],
+        "DEN_PORT": [ { "value": "den", "resolve_type": "user", "usage": "all" } ],
+        "PSCLK_PORT": [ { "value": "psclk", "resolve_type": "user", "usage": "all" } ],
+        "PSEN_PORT": [ { "value": "psen", "resolve_type": "user", "usage": "all" } ],
+        "PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "user", "usage": "all" } ],
+        "PSDONE_PORT": [ { "value": "psdone", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "125", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USE_MAX_I_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_O_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "user", "usage": "all" } ],
+        "PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "user", "usage": "all" } ],
+        "SUMMARY_STRINGS": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_LOCKED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CALC_DONE": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_RESET": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_POWER_DOWN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_STATUS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_FREEZE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLK_VALID": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_INCLK_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLKFB_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "RESET_PORT": [ { "value": "reset", "resolve_type": "user", "usage": "all" } ],
+        "LOCKED_PORT": [ { "value": "locked", "resolve_type": "user", "usage": "all" } ],
+        "POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "user", "usage": "all" } ],
+        "CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "user", "usage": "all" } ],
+        "STATUS_PORT": [ { "value": "STATUS", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "user", "usage": "all" } ],
+        "INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "user", "usage": "all" } ],
+        "SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "SS_MOD_FREQ": [ { "value": "250", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "OVERRIDE_MMCM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_DIVCLK_DIVIDE": [ { "value": "4", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_CLKFBOUT_MULT_F": [ { "value": "16.875", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_CASCADE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLOCK_HOLD": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_STARTUP_WAIT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT0_DIVIDE_F": [ { "value": "6.750", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT1_DIVIDE": [ { "value": "13", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OVERRIDE_PLL": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PLL_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "PLL_CLKFBOUT_MULT": [ { "value": "4", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "user", "usage": "all" } ],
+        "PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKIN_PERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "user", "usage": "all" } ],
+        "PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "RESET_TYPE": [ { "value": "ACTIVE_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "USE_SAFE_CLOCK_STARTUP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLOCK_SEQUENCING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "USE_BOARD_FLOW": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "RESET_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CDDC": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "user", "usage": "all" } ],
+        "CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CLKOUTPHY": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUTPHY_REQUESTED_FREQ": [ { "value": "600.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_JITTER": [ { "value": "162.582", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_PHASE_ERROR": [ { "value": "137.238", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_JITTER": [ { "value": "185.296", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_PHASE_ERROR": [ { "value": "137.238", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "INPUT_MODE": [ { "value": "frequency", "resolve_type": "user", "usage": "all" } ],
+        "INTERFACE_SELECTION": [ { "value": "Enable_AXI", "resolve_type": "user", "usage": "all" } ],
+        "AXI_DRP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PHASE_DUTY_CONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ]
+      },
+      "model_parameters": {
+        "C_CLKOUT2_USED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_ENABLE_CLOCK_MONITOR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK2": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK3": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRECISION": [ { "value": "1", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT1_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT2_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT3_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT4_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "c_component_name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_FREQ_SYNTH": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_PHASE_ALIGNMENT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_MIN_POWER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MIN_O_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MAX_I_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_PHASE_SHIFT": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_SWITCHOVER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_RECONFIG": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_SPREAD_SPECTRUM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FAST_SIMULATION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMTYPE_SEL": [ { "value": "AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_CLK_VALID": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_FREQ": [ { "value": "200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_RESET": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_RESET_LOW": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_LOCKED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKFB_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_POWER_DOWN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_STATUS": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FREEZE": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_NUM_OUT_CLKS": [ { "value": "2", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW0": [ { "value": "Input Clock   Freq (MHz)    Input Jitter (UI)", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW1": [ { "value": "__primary_________200.000____________0.010", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW2": [ { "value": "no_secondary_input_clock ", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0A": [ { "value": " Output     Output      Phase    Duty Cycle   Pk-to-Pk     Phase", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0B": [ { "value": "  Clock     Freq (MHz)  (degrees)    (%)     Jitter (ps)  Error (ps)", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW1": [ { "value": "clk_out1__125.00000______0.000______50.0______162.582____137.238", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW2": [ { "value": "clk_out2__64.90385______0.000______50.0______185.296____137.238", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW3": [ { "value": "no_CLK_OUT3_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW4": [ { "value": "no_CLK_OUT4_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW5": [ { "value": "no_CLK_OUT5_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW6": [ { "value": "no_CLK_OUT6_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW7": [ { "value": "no_CLK_OUT7_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "125", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_OUT_FREQ": [ { "value": "125.00000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_OUT_FREQ": [ { "value": "64.90385", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USE_SAFE_CLOCK_STARTUP": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLOCK_SEQUENCING": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_NOTES": [ { "value": "None", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_MULT_F": [ { "value": "16.875", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_CASCADE": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_CLOCK_HOLD": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_DIVCLK_DIVIDE": [ { "value": "4", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_STARTUP_WAIT": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DIVIDE_F": [ { "value": "6.750", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DIVIDE": [ { "value": "13", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_NOTES": [ { "value": "No notes", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_MULT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKIN_PERIOD": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLOCK_MGR_TYPE": [ { "value": "NA", "resolve_type": "generated", "usage": "all" } ],
+        "C_OVERRIDE_MMCM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OVERRIDE_PLL": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "generated", "usage": "all" } ],
+        "C_RESET_PORT": [ { "value": "reset", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCKED_PORT": [ { "value": "locked", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "generated", "usage": "all" } ],
+        "C_DADDR_PORT": [ { "value": "daddr", "resolve_type": "generated", "usage": "all" } ],
+        "C_DCLK_PORT": [ { "value": "dclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_DRDY_PORT": [ { "value": "drdy", "resolve_type": "generated", "usage": "all" } ],
+        "C_DWE_PORT": [ { "value": "dwe", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIN_PORT": [ { "value": "din", "resolve_type": "generated", "usage": "all" } ],
+        "C_DOUT_PORT": [ { "value": "dout", "resolve_type": "generated", "usage": "all" } ],
+        "C_DEN_PORT": [ { "value": "den", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSCLK_PORT": [ { "value": "psclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSEN_PORT": [ { "value": "psen", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSDONE_PORT": [ { "value": "psdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "generated", "usage": "all" } ],
+        "C_STATUS_PORT": [ { "value": "STATUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "generated", "usage": "all" } ],
+        "C_INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKIN1_JITTER_PS": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MOD_PERIOD": [ { "value": "4000", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_HAS_CDDC": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUTPHY_MODE": [ { "value": "VCO", "resolve_type": "generated", "usage": "all" } ],
+        "C_ENABLE_CLKOUTPHY": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_INTERFACE_SELECTION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_ADDR_WIDTH": [ { "value": "11", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_DATA_WIDTH": [ { "value": "32", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_POWER_REG": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVCLK": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_3": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE1_AUTO": [ { "value": "1", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE2_AUTO": [ { "value": "1.9259259259259258", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE3_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE4_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE5_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE6_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE7_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV5": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV6": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV7": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_ACTUAL_FREQ": [ { "value": "125.00000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_ACTUAL_FREQ": [ { "value": "64.90385", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_M_MAX": [ { "value": "64.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_M_MIN": [ { "value": "2.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MAX": [ { "value": "80.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MAX": [ { "value": "128.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MIN": [ { "value": "600.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MAX": [ { "value": "1200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ]
+      },
+      "project_parameters": {
+        "ARCHITECTURE": [ { "value": "artix7" } ],
+        "BASE_BOARD_PART": [ { "value": "" } ],
+        "BOARD_CONNECTIONS": [ { "value": "" } ],
+        "DEVICE": [ { "value": "xc7a35t" } ],
+        "PACKAGE": [ { "value": "fgg484" } ],
+        "PREFHDL": [ { "value": "VERILOG" } ],
+        "SILICON_REVISION": [ { "value": "" } ],
+        "SIMULATOR_LANGUAGE": [ { "value": "MIXED" } ],
+        "SPEEDGRADE": [ { "value": "-1" } ],
+        "STATIC_POWER": [ { "value": "" } ],
+        "TEMPERATURE_GRADE": [ { "value": "" } ]
+      },
+      "runtime_parameters": {
+        "IPCONTEXT": [ { "value": "IP_Flow" } ],
+        "IPREVISION": [ { "value": "16" } ],
+        "MANAGED": [ { "value": "TRUE" } ],
+        "OUTPUTDIR": [ { "value": "../../../../eth_generator_top.gen/sources_1/ip/clk_wiz_ctrl_inst" } ],
+        "SELECTEDSIMMODEL": [ { "value": "" } ],
+        "SHAREDDIR": [ { "value": "." } ],
+        "SWVERSION": [ { "value": "2025.1" } ],
+        "SYNTHESISFLOW": [ { "value": "OUT_OF_CONTEXT" } ]
+      }
+    },
+    "boundary": {
+      "ports": {
+        "reset": [ { "direction": "in", "driver_value": "0" } ],
+        "clk_in1": [ { "direction": "in" } ],
+        "clk_out1": [ { "direction": "out" } ],
+        "clk_out2": [ { "direction": "out" } ],
+        "locked": [ { "direction": "out" } ]
+      },
+      "interfaces": {
+        "reset": {
+          "vlnv": "xilinx.com:signal:reset:1.0",
+          "abstraction_type": "xilinx.com:signal:reset_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "POLARITY": [ { "value": "ACTIVE_HIGH", "value_src": "constant", "usage": "all" } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "RESET_BOARD_INTERFACE", "value_src": "constant", "usage": "all" } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "RST": [ { "physical_name": "reset" } ]
+          }
+        },
+        "clock_CLK_IN1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "CLK_IN1_BOARD_INTERFACE", "usage": "all", "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_IN1": [ { "physical_name": "clk_in1" } ]
+          }
+        },
+        "clock_CLK_OUT1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT1": [ { "physical_name": "clk_out1" } ]
+          }
+        },
+        "clock_CLK_OUT2": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT2": [ { "physical_name": "clk_out2" } ]
+          }
+        }
+      }
+    }
+  }
+}

designs/reflectometer/reflectometer.sv

@@ -0,0 +1,393 @@
+`timescale 1 ns / 1 ns
+
+module reflectometer_top #(
+    parameter int unsigned DAC_DATA_WIDTH = 14,
+    parameter int unsigned ADC_DATA_WIDTH = 12,
+    parameter PACK_FACTOR = 1,
+    parameter PROCESS_MODE = 0,
+    parameter ACCUM_WIDTH = 32,
+    parameter N_MAX = 4096,
+    parameter WINDOW_SIZE = 65,
+    parameter PACKET_SIZE = 1024
+)(
+    input               sys_clk_p,
+    input               sys_clk_n,
+    input               rst_n,
+
+    output [3:0]        led,
+
+    output              e_reset,
+    output              e_mdc,
+    inout               e_mdio,
+
+    output [3:0]        rgmii_txd,
+    output              rgmii_txctl,
+    output              rgmii_txc,
+    input  [3:0]        rgmii_rxd,
+    input               rgmii_rxctl,
+    input               rgmii_rxc,
+
+    // DAC
+
+    (* MARK_DEBUG="true" *) output debug_dac
+
+    // ADC
+
+    input [ADC_DATA_WIDTH-1:0] adc_data_in;
+    input adc_out_of_range;
+
+);
+    // temp
+    wire              p2_clk;
+    wire              p2_wrt;
+    (* MARK_DEBUG="true" *) wire [13:0]       p2_data;
+    assign debug_dac = p2_data[13];
+    // -------------------------------------------------------------------------
+    // Internal GMII-side signals
+    // -------------------------------------------------------------------------
+    wire  [7:0] gmii_txd;
+    wire        gmii_tx_en;
+    wire        gmii_tx_er;
+    wire        gmii_tx_clk;
+    wire        gmii_crs;
+    wire        gmii_col;
+    wire  [7:0] gmii_rxd_i;
+    wire        gmii_rx_dv;
+    wire        gmii_rx_er;
+    wire        gmii_rx_clk;
+
+    wire [31:0] pack_total_len;
+
+    wire        e_rx_dv;
+    wire [7:0]  e_rxd;
+    wire        e_tx_en;
+    wire [7:0]  e_txd;
+    wire        e_rst_n;
+    wire        sys_clk;
+
+    wire        duplex_mode;
+    
+
+    assign duplex_mode = 1'b1;
+
+    // -------------------------------------------------------------------------
+    // System clock buffer (200 MHz differential input)
+    // -------------------------------------------------------------------------
+    IBUFDS sys_clk_ibufgds (
+        .O  (sys_clk),
+        .I  (sys_clk_p),
+        .IB (sys_clk_n)
+    );
+
+    // -------------------------------------------------------------------------
+    // IDELAYCTRL
+    // -------------------------------------------------------------------------
+    (* IODELAY_GROUP = "rgmii_idelay_group" *)
+    IDELAYCTRL IDELAYCTRL_inst (
+        .RDY    (),
+        .REFCLK (sys_clk),
+        .RST    (1'b0)
+    );
+
+    // -------------------------------------------------------------------------
+    // Generated clocks for controller
+    // Need to create this IP in Vivado:
+    //  input : 200 MHz
+    //  output0: 130 MHz
+    //  output1: 65 MHz
+    // -------------------------------------------------------------------------
+    wire dac_clk;
+    wire adc_clk;
+    wire clk_wiz_locked;
+
+    clk_wiz_ctrl_inst clk_wiz_ctrl_inst (
+        .clk_in1   (sys_clk),
+        .reset    (~rst_n),
+        .clk_out1  (dac_clk),   // 130 MHz
+        .clk_out2  (adc_clk),   // 65 MHz
+        .locked    (clk_wiz_locked)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII <-> RGMII conversion
+    // -------------------------------------------------------------------------
+    util_gmii_to_rgmii util_gmii_to_rgmii_m0 (
+        .reset           (1'b0),
+        .rgmii_td        (rgmii_txd),
+        .rgmii_tx_ctl    (rgmii_txctl),
+        .rgmii_txc       (rgmii_txc),
+        .rgmii_rd        (rgmii_rxd),
+        .rgmii_rx_ctl    (rgmii_rxctl),
+        .gmii_rx_clk     (gmii_rx_clk),
+        .gmii_txd        (e_txd),
+        .gmii_tx_en      (e_tx_en),
+        .gmii_tx_er      (1'b0),
+        .gmii_tx_clk     (gmii_tx_clk),
+        .gmii_crs        (gmii_crs),
+        .gmii_col        (gmii_col),
+        .gmii_rxd        (gmii_rxd_i),
+        .rgmii_rxc       (rgmii_rxc),
+        .gmii_rx_dv      (gmii_rx_dv),
+        .gmii_rx_er      (gmii_rx_er),
+        .speed_selection (2'b10),
+        .duplex_mode     (duplex_mode)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII arbitration / adaptation
+    // -------------------------------------------------------------------------
+    gmii_arbi arbi_inst (
+        .clk            (gmii_tx_clk),
+        .rst_n          (rst_n),
+        .speed          (2'b10),
+        .link           (1'b1),
+        .pack_total_len (pack_total_len),
+        .e_rst_n        (e_rst_n),
+        .gmii_rx_dv     (gmii_rx_dv),
+        .gmii_rxd       (gmii_rxd_i),
+        .gmii_tx_en     (gmii_tx_en),
+        .gmii_txd       (gmii_txd),
+        .e_rx_dv        (e_rx_dv),
+        .e_rxd          (e_rxd),
+        .e_tx_en        (e_tx_en),
+        .e_txd          (e_txd)
+    );
+
+    // -------------------------------------------------------------------------
+    // axis_mac interface
+    // RX stream from Ethernet goes into controller
+    // TX stream is unused for now
+    // -------------------------------------------------------------------------
+    wire        req_ready;
+
+    reg         send_req;
+    reg  [15:0] data_length;
+
+    reg  [7:0]  s_axis_tx_tdata;
+    reg         s_axis_tx_tvalid;
+    wire        s_axis_tx_tready;
+    reg         s_axis_tx_tlast;
+
+    (* MARK_DEBUG="true" *) wire [7:0]  m_axis_rx_tdata;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tvalid;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tlast;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tready;
+
+    // Always ready to accept RX payload bytes
+    assign m_axis_rx_tready = 1'b1;
+
+    // TX disabled
+    always @(*) begin
+        send_req        = 1'b0;
+        data_length     = 16'd0;
+        s_axis_tx_tdata = 8'd0;
+        s_axis_tx_tvalid= 1'b0;
+        s_axis_tx_tlast = 1'b0;
+    end
+
+    axis_mac axis_mac0 (
+        .gmii_tx_clk       (gmii_tx_clk),
+        .gmii_rx_clk       (gmii_rx_clk),
+        .rst_n             (e_rst_n),
+
+        .gmii_rx_dv        (e_rx_dv),
+        .gmii_rxd          (e_rxd),
+        .gmii_tx_en        (gmii_tx_en),
+        .gmii_txd          (gmii_txd),
+
+        .send_req          (send_req),
+        .data_length       (data_length),
+        .req_ready         (req_ready),
+
+        .s_axis_tx_tdata   (s_axis_tx_tdata),
+        .s_axis_tx_tvalid  (s_axis_tx_tvalid),
+        .s_axis_tx_tready  (s_axis_tx_tready),
+        .s_axis_tx_tlast   (s_axis_tx_tlast),
+
+        .m_axis_rx_tdata   (m_axis_rx_tdata),
+        .m_axis_rx_tvalid  (m_axis_rx_tvalid),
+        .m_axis_rx_tready  (m_axis_rx_tready),
+        .m_axis_rx_tlast   (m_axis_rx_tlast)
+    );
+
+    // PHY reset helper from your original example
+    reset reset_m0 (
+        .clk   (sys_clk),
+        .key1  (rst_n),
+        .rst_n (e_reset)
+    );
+
+    // MDIO lines are not driven here yet
+    assign e_mdc  = 1'b0;
+    assign e_mdio = 1'bz;
+
+    // -------------------------------------------------------------------------
+    // Controller reset
+    // Use both external reset and clk_wiz lock
+    // -------------------------------------------------------------------------
+    wire ctrl_rst_n = rst_n & clk_wiz_locked;
+
+    // -------------------------------------------------------------------------
+    // Debug finish generator (still used here, since generator doesn't have finish signal)
+    //
+    // After each adc_start pulse generates one finish pulse after some delay.
+    // This is just for first bring-up so the controller can leave busy state
+    // If you don't want this, replace with:
+    // wire finish_dbg = 1'b0;
+    // -------------------------------------------------------------------------
+    (* MARK_DEBUG="true" *) logic        finish;
+
+    // Controller outputs to debug
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_width;
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_period;
+    (* MARK_DEBUG="true" *) wire [DAC_DATA_WIDTH-1:0] dac_pulse_height;
+    (* MARK_DEBUG="true" *) wire [15:0]               dac_pulse_num;
+
+    (* MARK_DEBUG="true" *) wire [31:0]               adc_pulse_period;
+    (* MARK_DEBUG="true" *) wire [15:0]               adc_pulse_num;
+
+    (* MARK_DEBUG="true" *) wire                      dac_start;
+    (* MARK_DEBUG="true" *) wire                      adc_start;
+    (* MARK_DEBUG="true" *) wire                      dac_rst;
+    (* MARK_DEBUG="true" *) wire                      adc_rst;
+
+
+    // -------------------------------------------------------------------------
+    // Controller
+    // ETH domain = gmii_rx_clk, because RX AXI master comes from axis_mac RX side
+    // -------------------------------------------------------------------------
+    control #(
+        .DAC_DATA_WIDTH(DAC_DATA_WIDTH)
+    ) udp_ctrl_inst (
+        .eth_clk_in        (gmii_rx_clk),
+        .dac_clk_in        (dac_clk),
+        .adc_clk_in        (adc_clk),
+        .rst_n             (ctrl_rst_n),
+
+        .s_axis_tdata      (m_axis_rx_tdata),
+        .s_axis_tvalid     (m_axis_rx_tvalid),
+        .s_axis_tready     (), // controller internally always ready in current version
+        .s_axis_tlast      (m_axis_rx_tlast),
+
+        .finish            (finish),
+
+        .dac_pulse_width   (dac_pulse_width),
+        .dac_pulse_period  (dac_pulse_period),
+        .dac_pulse_height  (dac_pulse_height),
+        .dac_pulse_num     (dac_pulse_num),
+
+        .adc_pulse_period  (adc_pulse_period),
+        .adc_pulse_num     (adc_pulse_num),
+
+        .dac_start         (dac_start),
+        .adc_start         (adc_start),
+
+        .dac_rst           (dac_rst),
+        .adc_rst           (adc_rst)
+    );
+
+    // -------------------------------------------------------------------------
+    // DAC
+    // -------------------------------------------------------------------------
+    generator #(
+        .DATA_WIDTH(DAC_DATA_WIDTH)
+    ) generator_inst (
+        .clk_in(dac_clk),
+        .rst(dac_rst),
+        .start(dac_start),
+        .pulse_width(dac_pulse_width),
+        .pulse_period(dac_pulse_period),
+        .pulse_height(dac_pulse_height),
+        .pulse_num(dac_pulse_num),
+        .pulse(p2_wrt ),
+        .pulse_height_out(p2_data)
+    );
+
+    // dac clk mgt
+    wire p2_clk_oddr;
+
+    ODDR #(
+        .DDR_CLK_EDGE("SAME_EDGE"),
+        .INIT(1'b0),
+        .SRTYPE("SYNC")
+    ) ODDR_p2_clk (
+        .Q (p2_clk_oddr),
+        .C (dac_clk),
+        .CE(1'b1),
+        .D1(1'b1),
+        .D2(1'b0),
+        .R (1'b0),
+        .S (1'b0)
+    );
+
+    OBUF OBUF_p2_clk (
+        .I(p2_clk_oddr),
+        .O(p2_clk)
+    );
+
+// -------------------------------------------------------------------------
+    // ADC
+    // -------------------------------------------------------------------------
+
+    logic [DATA_WIDTH*PACK_FACTOR-1:0]  accum_m_axis_tdata;
+    logic acum_m_axis_tvalid;
+
+    sampler 
+    #(
+        .DATA_WIDTH(ADC_DATA_WIDTH),
+        .PACK_FACTOR(PACK_FACTOR),
+        .PROCESS_MODE(PROCESS_MODE)
+    )
+    sampler_dut
+    (
+       .clk_in(adc_clk),
+       .rst(adc_rst),
+       .data_in(adc_data_in),
+       .out_of_range(adc_out_of_range),
+       .m_axis_tdata(accum_m_axis_tdata),
+       .m_axis_tvalid(acum_m_axis_tvalid)
+    );
+
+    // -------------------------------------------------------------------------
+    // Accumulator
+    // -------------------------------------------------------------------------
+
+    accumulator_top
+    #(
+        .DATA_WIDTH(ADC_DATA_WIDTH),
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .N_MAX(N_MAX),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    )
+    accumulator_top_dut
+    (
+        .clk_in(adc_clk),
+        .rst(adc_rst),
+        .s_axis_tdata(accum_m_axis_tdata),
+        .s_axis_tvalid(acum_m_axis_tvalid),
+        .start(adc_start),
+        .smp_num(adc_pulse_period),
+        .seq_num(adc_pulse_num),
+
+        .eth_clk_in(gmii_rx_clk),
+        .req_ready(req_ready),
+        .send_req(send_req),
+        .m_axis_tdata(m_axis_rx_tdata),
+        .m_axis_tvalid(m_axis_rx_tvalid),
+        .m_axis_tready(m_axis_rx_tready),
+        .m_axis_tlast(m_axis_rx_tlast),
+
+        .finish(finish)
+    );
+
+
+    // -------------------------------------------------------------------------
+    // Simple LED status
+    // -------------------------------------------------------------------------
+    assign led[0] = clk_wiz_locked;
+    assign led[1] = m_axis_rx_tvalid;
+    assign led[2] = dac_start;
+    assign led[3] = debug_dac;
+
+endmodule

rtl/accum/README.md

@@ -0,0 +1,39 @@
+# Аккумулятор
+Модуль аккумуляции данных для последующего усреднения. Принимает данные с входного потока АХI-Stream фиксированной ширины (задается параметрически), суммируя их сначала по окнам, а затем со значениями из предыдущей последовательности.
+
+## Список парамтеров:
+- DATA_WIDTH - ширина входных данных, получаемых с АЦП
+- ACCUM_WIDTH - размер данных для аккумуляции, должен быть степенью числа 2. По умолчанию - 32
+- N_MAX - максимальное число окон в последовательности. Должно быть степенью числа 2. Влияет на размер используемой памяти.
+- WINDOW_SIZE - размер окна усреднения
+- PACKET_SIZE - размер выходного пакета
+
+## Иерархия:
+```
+├── accum_top - полная сборка аккумулятора
+│   ├── accum - основная логика аккумуляции по окнам и последовательностям
+│   │   ├── adder - модуль сложения по окнам
+│   ├── out_axis_fifo - модуль для выдачи данных наружу в другом частотном домене
+```
+## Список входных портов:
+- clk_in - частота входных данных
+- rst - сброс всего
+- [DATA_WIDTH-1:0] s_axis_tdata - входные данные
+- s_axis_tvalid - валидность входных данных
+- start - начало аккумуляции
+- [31:0] smp_num - число сэмплов (должно быть кратно WINDOW_SIZE)
+- [15:0] seq_num - число последовательностей аккумуляции
+- eth_clk_in - частота для выходных данных на ethernet
+- req_ready - готовность отправителя начать принимать данные
+- m_axis_tready - готовность выходного axis
+
+
+## Список выходных портов:
+- send_req - сигнал начала отправки данных
+- [7:0] m_axis_tdata - данные выходного axis
+- m_axis_tvalid - валидность выходного axis
+- m_axis_tlast - последний пакет в axis
+- finish - конец отправки всех данных, полный цикл работы завершен
+
+## Логика работы:
+Модуль начинает работу при получении сигнала start. Сразу после начала работы можно подавать данные на входной axis, они будут суммироваться по WINDOW_SIZE штук и отправляться на хранение. Так будет сделано для последовательности длиной smp_num чисел, затем начинается новая последовательность - всего таких будет seq_num штук. Каждая последующая последовательность также суммируется по окнам, а затем полученные значения прибавляются к тем же значениям предыдущей последовательности. Таким образом, выполняется суммирование по двум осям, и из исходных данных seq_num по smp_num чисел остается вектор длиной 1 x (smp_num / WINDOW_SIZE). После накопления всех данных начинается выдача. Выдача осуществляется на выходной AXI stream, работающий в домене eth_clk, и имеющий ширину 8 бит - предполагается, что выдача пойдет на ethernet-udp. Когда поднят сигнал req_ready, модуль будет отправлять send_req (запрос отправки пакета), и по готовности m_axis_tready начнет выдавать пакет размер PACKET_SIZE байт. Если данные нельзя ровно разложить по пакетам, то в последнем пакете могут быть отправлены рандомные данные из памяти. После окончания отправки всех пакетов будет поднят сигнал finish.

rtl/accum/src/accum.sv

@@ -0,0 +1,271 @@
+`timescale 1ns / 1ps
+
+module accumulator
+#(
+    parameter DATA_WIDTH = 12,
+    parameter ACCUM_WIDTH = 32,
+    parameter N_MAX = 4096,
+    parameter WINDOW_SIZE = 4,
+    parameter PACKET_SIZE = 8,
+    parameter READ_BATCH_SIZE =(PACKET_SIZE*8)/(ACCUM_WIDTH)
+    )
+(
+    input clk_in,
+    input rst,
+    input [DATA_WIDTH-1:0] s_axis_tdata,
+    input s_axis_tvalid,
+    input start,
+    input [31:0] smp_num,
+    input [15:0] seq_num,
+
+    output [ACCUM_WIDTH-1:0] out_data,
+    output out_valid,
+    output readout_begin,
+    input batch_req,
+    input finish
+    );
+
+    logic [31:0] smp_num_reg, cnt_smp_num;
+    logic [15:0] seq_num_reg, cnt_seq_num;
+    logic [15:0] cnt_addr, addra, addrb;
+
+    logic [ACCUM_WIDTH-1:0] data;
+    logic valid_data;
+    logic [ACCUM_WIDTH-1:0] data_bram_in, data_bram_out;
+    logic wea, enb;
+
+    logic readout_begin_reg;
+    logic [ACCUM_WIDTH-1:0] out_data_reg;
+    logic out_valid_reg;
+    logic finish_reg, finish_buf;
+
+    // registers for port b data request
+    reg req_data_b;
+    reg [15:0] req_addr_b;
+
+    typedef enum logic [3:0] {
+        IDLE,
+        INIT_MEM,
+        BEGIN_SEQ,
+        REQ_WORD_B,
+        ACCUM,
+        READOUT_START,
+        READOUT_AWAIT,
+        READOUT_DELAY,
+        READOUT_PUT,
+        READOUT_LAST,
+        FINISH
+    } wr_state_t;
+    (* MARK_DEBUG="true" *) wr_state_t wr_state;
+
+    always @(posedge clk_in) begin
+        if (rst) begin
+            smp_num_reg <= '0;
+            cnt_smp_num <= '0;
+            seq_num_reg <= '0;
+            cnt_seq_num <= '0;
+            cnt_addr <= '0;
+            wea <= 0;
+            enb <= 0;
+            wr_state <= IDLE;
+            finish_reg <= 0;
+            out_valid_reg <= 0;
+        end else begin
+            finish_buf <= finish;
+
+            // FSM
+            case(wr_state)
+
+            IDLE: begin
+                // wait for start signal
+                wea <= 0;
+                enb <= 0;
+                readout_begin_reg <= 0;
+                finish_reg <= 0;
+                out_valid_reg <= 0;
+                if (start) begin
+                    smp_num_reg <= smp_num;
+                    seq_num_reg <= seq_num;
+                    wr_state <= INIT_MEM;
+                end
+
+            end
+            INIT_MEM: begin
+                // first run to initialize memory with first batch of values
+                wea <= 0;
+                if (valid_data) begin
+                    data_bram_in <= data;
+                    addra <= cnt_addr;
+                    wea <= 1;
+                    cnt_addr <= cnt_addr + 1;
+                    cnt_smp_num <= cnt_smp_num + WINDOW_SIZE;
+
+                end
+                if (cnt_smp_num >= smp_num_reg) begin
+                    wr_state <= BEGIN_SEQ;
+                end
+
+            end
+            BEGIN_SEQ: begin
+                // start new acc seq
+                wea <= 0;
+                enb <= 0;
+                if (cnt_seq_num == seq_num_reg - 1) begin
+                    cnt_seq_num <= '0;
+                    cnt_smp_num <= '0;
+                    cnt_addr <= '0;
+                    wr_state <= READOUT_START;
+                    addrb <= '0;
+                    enb <= 0;
+                end else begin
+                    // beginning of new data sequence
+                    cnt_seq_num <= cnt_seq_num + 1;
+                    cnt_smp_num <= '0;
+                    cnt_addr <= '0;
+                    wea <= 0;
+                    addrb <= 0;
+                    wr_state <= REQ_WORD_B;
+                end
+            end
+
+            REQ_WORD_B: begin
+                // pre-request data for port b
+                wea <= 0;
+                enb <= 1;
+                addrb <= cnt_addr;
+                wr_state <= ACCUM;
+            end
+
+            ACCUM: begin
+                // sum mem+input
+                enb <= 0;
+                if (valid_data) begin
+                    addra <= cnt_addr;
+                    wea <= 1;
+                    data_bram_in <= data + data_bram_out;
+                    cnt_smp_num <= cnt_smp_num + WINDOW_SIZE;
+                    if (cnt_smp_num + WINDOW_SIZE >= smp_num_reg) begin
+                        wr_state <= BEGIN_SEQ;
+                    end else begin
+                        cnt_addr <= cnt_addr + 1;
+                        wr_state <= REQ_WORD_B;
+                    end
+                end
+            end
+            READOUT_START: begin
+                readout_begin_reg <= 1'b1;
+                wr_state <= READOUT_AWAIT;
+                enb <= 0;
+            end
+
+            READOUT_AWAIT: begin
+                // req await + delay for every-clock readout.
+                if (batch_req) begin
+                    enb <= 1;
+                    wr_state <= READOUT_DELAY;
+                end else if (finish_buf) begin
+                    wr_state <= FINISH;
+                end else begin
+                    enb <= 0;
+                    out_valid_reg <= 0;
+                end
+            end
+
+            READOUT_DELAY: begin
+                // wait for mem latency
+                addrb <= addrb + 1;
+                wr_state <= READOUT_PUT;
+            end
+
+            READOUT_PUT: begin
+                // main data output
+                if ((addrb % READ_BATCH_SIZE) == 0) begin
+                    wr_state <= READOUT_LAST;
+                    enb <= 0;
+                end else addrb <= addrb + 1;
+
+                out_valid_reg <= 1;
+                out_data_reg <= data_bram_out;
+            end
+
+            READOUT_LAST: begin
+                // last word of packet
+                out_valid_reg <= 0;
+                out_data_reg <= data_bram_out;
+                wr_state <= READOUT_START;
+            end
+
+            FINISH: begin
+                out_valid_reg <= 0;
+                enb <= 0;
+                wr_state <= IDLE;
+            end
+
+            default: wr_state <= IDLE;
+            endcase
+        end
+    end
+
+
+    adder
+    #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .ACCUM_WIDTH(ACCUM_WIDTH)
+    ) adder_dut
+    (
+        .clk_in(clk_in),
+        .rst(rst),
+        .s_axis_tdata(s_axis_tdata),
+        .s_axis_tvalid(s_axis_tvalid),
+        .sum_data(data),
+        .sum_valid(valid_data)
+    );
+
+    xpm_memory_sdpram #(
+      .ADDR_WIDTH_A(16),               // DECIMAL
+      .ADDR_WIDTH_B(16),               // DECIMAL
+      .AUTO_SLEEP_TIME(0),            // DECIMAL
+      .BYTE_WRITE_WIDTH_A(ACCUM_WIDTH),        // DECIMAL
+      .CASCADE_HEIGHT(0),             // DECIMAL
+      .CLOCKING_MODE("common_clock"), // String
+      .ECC_MODE("no_ecc"),            // String
+      .MEMORY_INIT_FILE("none"),      // String
+      .MEMORY_INIT_PARAM("0"),        // String
+      .MEMORY_OPTIMIZATION("true"),   // String
+      .MEMORY_PRIMITIVE("auto"),      // String
+      .MEMORY_SIZE(N_MAX*ACCUM_WIDTH),             // DECIMAL
+      .MESSAGE_CONTROL(0),            // DECIMAL
+      .READ_DATA_WIDTH_B(ACCUM_WIDTH),         // DECIMAL
+      .READ_LATENCY_B(1),             // DECIMAL
+      .READ_RESET_VALUE_B("0"),       // String
+      .RST_MODE_A("SYNC"),            // String
+      .RST_MODE_B("SYNC"),            // String
+      .SIM_ASSERT_CHK(0),             // DECIMAL; 0=disable simulation messages, 1=enable simulation messages
+      .USE_EMBEDDED_CONSTRAINT(0),    // DECIMAL
+      .USE_MEM_INIT(1),               // DECIMAL
+      .USE_MEM_INIT_MMI(0),           // DECIMAL
+      .WAKEUP_TIME("disable_sleep"),  // String
+      .WRITE_DATA_WIDTH_A(ACCUM_WIDTH),        // DECIMAL
+      .WRITE_MODE_B("no_change"),     // String
+      .WRITE_PROTECT(1)               // DECIMAL
+   )
+   xpm_memory_sdpram_inst (
+
+      .doutb(data_bram_out),
+
+      .addra(addra),
+      .addrb(addrb),
+      .clka(clk_in),
+      .clkb(clk_in),
+      .dina(data_bram_in),
+      .ena(1'b1),
+      .enb(enb),
+      .wea(wea)
+   );
+
+    assign readout_begin = readout_begin_reg;
+    assign out_data = out_data_reg;
+    assign out_valid = out_valid_reg;
+
+endmodule

rtl/accum/src/accum_top.sv

@@ -0,0 +1,92 @@
+`timescale 1ns / 1ps
+
+module accumulator_top
+#(
+    parameter DATA_WIDTH = 12,
+    parameter ACCUM_WIDTH = 32,
+    parameter N_MAX = 4096,
+    parameter WINDOW_SIZE = 65,
+    parameter PACKET_SIZE = 1024,
+    parameter READ_BATCH_SIZE =(PACKET_SIZE*8)/(ACCUM_WIDTH)
+    )
+(
+    // main clk
+    input clk_in,
+    input rst,
+    
+    // input data
+    input [DATA_WIDTH-1:0] s_axis_tdata,
+    input s_axis_tvalid,
+
+    // parameters
+    input start,
+    input [31:0] smp_num,
+    input [15:0] seq_num,
+
+    // eth signals
+    input eth_clk_in,
+    input req_ready,
+    output send_req,
+
+    // output axis
+    output logic [7:0]      m_axis_tdata,
+    output logic            m_axis_tvalid,
+    input  logic            m_axis_tready,
+    output logic            m_axis_tlast,
+
+    output logic finish
+    );
+
+    wire [ACCUM_WIDTH-1:0] out_data;
+    wire out_valid;
+    wire readout_begin;
+    wire batch_req;
+
+    accumulator #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .N_MAX(N_MAX),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    ) accum_main (
+        .clk_in(clk_in),
+        .rst(rst),
+        .s_axis_tdata(s_axis_tdata),
+        .s_axis_tvalid(s_axis_tvalid),
+        .start(start),
+        .smp_num(smp_num),
+        .seq_num(seq_num),
+        .out_data(out_data),
+        .out_valid(out_valid),
+        .readout_begin(readout_begin),
+        .batch_req(batch_req),
+        .finish(finish)
+    );
+
+    out_axis_fifo #(
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    ) output_async_fifo (
+        .eth_clk_in    (eth_clk_in),
+        .acc_clk_in    (clk_in),
+        .rst           (rst),
+        .smp_num       (smp_num),
+
+        .m_axis_tdata  (m_axis_tdata),
+        .m_axis_tvalid (m_axis_tvalid),
+        .m_axis_tready (m_axis_tready),
+        .m_axis_tlast  (m_axis_tlast),
+
+        .acc_din       (out_data),
+        .din_valid     (out_valid),
+
+        .readout_begin (readout_begin),
+
+        .req_ready     (req_ready),
+        .send_req      (send_req),
+
+        .batch_req     (batch_req),
+        .finish        (finish)
+    );
+endmodule

rtl/accum/src/adder.sv

@@ -0,0 +1,52 @@
+`timescale 1ns / 1ps
+
+
+module adder
+#(
+    parameter DATA_WIDTH = 12,
+    parameter WINDOW_SIZE = 4,
+    parameter ACCUM_WIDTH = 32
+    )
+(
+    input clk_in,
+    input rst,
+    input [DATA_WIDTH-1:0] s_axis_tdata,
+    input s_axis_tvalid,
+    
+    output [ACCUM_WIDTH-1:0] sum_data,
+    output sum_valid
+    );
+
+    logic [ACCUM_WIDTH-1:0] accum, res;
+    logic [DATA_WIDTH-1:0] axis_data;
+    logic res_valid, axis_valid;
+ (* MARK_DEBUG = "TRUE" *)   logic [15:0] cnt;
+    
+    always @(posedge clk_in) begin
+        if (rst) begin
+            accum <= '0;
+            cnt <= '0;
+            res <= '0;
+            res_valid <= 0;
+        end else begin
+            res_valid <= 0;
+            axis_data <= s_axis_tdata;
+            axis_valid <= s_axis_tvalid;
+            if ( axis_valid) begin
+                if (cnt == WINDOW_SIZE-1) begin
+                    res <= accum + axis_data;
+                    res_valid <= 1;
+                    accum <= '0;
+                    cnt <= '0;
+                end else begin
+                    accum <= accum + axis_data;
+                    cnt   <= cnt + 1;
+                end
+            end
+        end
+    end 
+   
+    assign sum_valid = res_valid;
+    assign sum_data = res;
+    
+endmodule

rtl/accum/src/out_axis_fifo.sv

@@ -0,0 +1,324 @@
+module out_axis_fifo #(
+    parameter ACCUM_WIDTH = 32,
+    parameter WINDOW_SIZE = 65,
+    parameter PACKET_SIZE = 1024
+) (
+    input  logic                eth_clk_in,
+    input  logic                acc_clk_in,
+    input  logic                rst,
+    input  logic [31:0]         smp_num,
+
+    // AXI stream master for output, eth_clk_in domain
+    output logic [7:0]          m_axis_tdata,
+    output logic                m_axis_tvalid,
+    input  logic                m_axis_tready,
+    output logic                m_axis_tlast,
+    // eth handshake
+    input  logic                req_ready,
+    output logic                send_req,
+    output logic [15:0]         udp_data_length,
+
+    // data from acc
+    input  logic [ACCUM_WIDTH-1:0]   acc_din,
+    input  logic                     din_valid,
+    
+    // input pulse
+    input  logic                readout_begin,
+
+    // output pulses
+    output logic batch_req,
+    output logic finish      
+);
+    // sync reset
+    reg [1:0] rst_sync_ff;
+    reg rst_eth;
+
+    always @(posedge acc_clk_in or posedge rst) begin
+        if (rst) begin
+            rst_sync_ff <= 2'b11;
+        end else begin
+            rst_sync_ff <= {rst_sync_ff[0], 1'b0};
+        end
+    end
+
+    assign rst_eth = rst_sync_ff[1];
+
+    logic [1:0] rst_acc_ff;
+    logic rst_acc;
+
+    always_ff @(posedge acc_clk_in or posedge rst) begin
+        if (rst)
+            rst_acc_ff <= 2'b11;
+        else
+            rst_acc_ff <= {rst_acc_ff[0], 1'b0};
+    end
+
+    assign rst_acc = rst_acc_ff[1];
+
+
+    // fifo params calc
+    // round up to be enough for 2xPACKET_SIZE storage
+    localparam int MIN_BYTES      = 2 * PACKET_SIZE;
+    localparam int MIN_BITS       = MIN_BYTES * 8;
+    localparam int MIN_WR_WORDS   = (MIN_BITS + ACCUM_WIDTH - 1) / ACCUM_WIDTH; // ceil div
+    localparam int WDEPTH_BITS    = $clog2(MIN_WR_WORDS);
+    localparam int FIFO_WDEPTH    = 1 << WDEPTH_BITS;
+
+    localparam int FIFO_RDEPTH     = FIFO_WDEPTH * ACCUM_WIDTH / 8;
+    localparam int RDEPTH_BITS     = $clog2(FIFO_RDEPTH) + 1;
+
+    wire wr_unavail;
+    wire wr_rst_busy;
+    reg rd_en;
+    
+    
+    typedef enum logic [2:0] {
+        WR_IDLE         = 3'd0,
+        WR_CHECK        = 3'd1,
+        WR_RUN          = 3'd2,
+        WR_END          = 3'd3
+    } wr_state_t;
+
+    (* MARK_DEBUG="true" *) wr_state_t wr_state;
+    
+    // Write FSM
+    reg [31:0] wr_cnt;       // current BIT mem ptr
+    reg [31:0] wr_batch_tgt; // next 'target' that should be written from batch
+    reg [31:0] wr_total;     // total BITS to be sent!
+
+    wire empty;
+
+    wire [WDEPTH_BITS:0] wr_data_count;
+
+    // NOTE:
+    // each written "acc_din" ACCUM_WIDTH word
+    // is counted as WINDOWS_SIZE samples actually
+    // because hw division for counters is painful
+    // so we just increased the counter sizes
+
+    always_ff @(posedge acc_clk_in) begin
+        if (rst_acc) begin
+            wr_state        <= WR_IDLE;
+            wr_cnt          <= 32'b0;
+            wr_batch_tgt    <= 32'b0;
+            wr_total        <= 32'b0;
+            batch_req       <= 0;
+            finish          <= 0;
+            
+        end else begin
+
+            case (wr_state)
+                // wait until readout is requested
+                WR_IDLE: begin
+                    if (readout_begin) begin 
+                        wr_cnt <= 32'b0;
+                        wr_state <= WR_CHECK;
+                        wr_total <= smp_num * ACCUM_WIDTH;
+                        wr_batch_tgt <= 32'b0;
+                        batch_req <= 0;
+                        finish <= 0;
+                    end
+                end
+                
+                // wait until we can request a word
+                // depends on prog_full signal
+                WR_CHECK: begin
+                    if ((wr_data_count < (FIFO_WDEPTH - (PACKET_SIZE / (ACCUM_WIDTH / 8)))) && ~wr_rst_busy) begin
+                        batch_req <= 1;
+                        // should give us exactly PACKET_SIZE * 8 bits
+                        // multiplied by WINDOW_SIZE, because we count 
+                        // each given ACCUM_WIDTH word as WINDOWS_SIZE samples !!!
+                        wr_batch_tgt <= wr_batch_tgt + (8 * WINDOW_SIZE * PACKET_SIZE);
+                        wr_state <= WR_RUN;
+                    end else begin
+                        batch_req <= 0;
+                    end
+                end
+
+                // wait until all requested packet is written
+                WR_RUN: begin
+                    batch_req <= 0;
+                    if (wr_cnt == wr_batch_tgt) begin
+                        // got enough words
+                        wr_state <= WR_END;
+                    end else if (wr_cnt > wr_batch_tgt) begin
+                        // weird case when accum gave us too much words
+                        // block resets
+                        wr_cnt <= 32'hffffffff;  // sort of signal for sim/ila
+                        wr_state <= WR_END;
+                    end
+
+                    if (din_valid) begin
+                        // data supplied
+                        // count as we got WINDOW_SIZE samples
+                        wr_cnt <= wr_cnt + ACCUM_WIDTH * WINDOW_SIZE;
+                    end
+                end
+
+                // check if this was last data batch
+                WR_END: begin
+                    // here we check that we sent enough data
+                    // wr_cnt should be by design PACKET_SIZE-aligned
+                    if (wr_cnt >= wr_total) begin
+                        // wait until all data is sent
+                        if (empty) begin
+                            finish <= 1;
+                            wr_state <= WR_IDLE;
+                        end
+                    end else begin
+                        // next word
+                        wr_state <= WR_CHECK;
+                    end
+                end
+            endcase
+        end
+    end
+
+    // Readout FSM with ethernet request
+
+    assign udp_data_length = PACKET_SIZE;  // fixed packet size
+    reg [15:0] sent_cnt;
+
+    typedef enum logic [2:0] {
+        RD_IDLE         = 3'd0,
+        RD_CHECK        = 3'd1,
+        RD_SEND         = 3'd2
+    } rd_state_t;
+
+    (* MARK_DEBUG="true" *) rd_state_t rd_state;
+
+    wire rd_valid;
+    wire [RDEPTH_BITS-1:0] rd_data_count;
+
+    always_ff @(posedge eth_clk_in) begin
+        if (rst_eth) begin
+            rd_state <= RD_IDLE;
+            send_req <= 1'b0;
+            sent_cnt <= 16'd0;
+            m_axis_tlast <= 1'b0;
+            m_axis_tvalid <= 1'b0;
+            rd_en <= 1'b0;
+            
+        end else begin
+
+            case (rd_state)
+                // wait until fifo has enough data to send
+                RD_IDLE: begin
+                    if (rd_data_count == PACKET_SIZE) begin
+                        // enough data to send packet, begin
+                        rd_state <= RD_CHECK;
+                    end
+                    send_req <= 1'b0;
+                    sent_cnt <= 16'd0;
+                    rd_en <= 1'b0;
+                    m_axis_tlast <= 1'b0;
+                    m_axis_tvalid <= 1'b0;
+                end
+
+                // await udp ready
+                RD_CHECK: begin
+                    if (req_ready) begin
+                        send_req <= 1'b1;
+                        rd_state <= RD_SEND;
+                    end
+                end
+
+                // send data
+                RD_SEND: begin
+                    // udp is ready and fifo is ready = sent
+                    send_req <= 1'b0;
+                    if (m_axis_tready && rd_valid) begin
+                        rd_en <= 1'b1;
+                        m_axis_tvalid <= 1'b1;
+                        sent_cnt <= sent_cnt + 1;
+                        // final packet of the batch
+                        if (sent_cnt == PACKET_SIZE - 1) begin
+                            rd_state <= RD_IDLE;
+                            m_axis_tlast <= 1'b1;
+                        end
+                    end else begin
+                        rd_en <= 1'b0;
+                        m_axis_tvalid <= 1'b0;
+                    end
+                end
+            endcase
+        end
+    end
+
+    logic [ACCUM_WIDTH-1:0] fifo_din_r, acc_din_reg, din_valid_reg;
+    logic                   fifo_wr_en_r;
+
+    always_ff @(posedge acc_clk_in) begin
+        if (rst_acc) begin
+            fifo_din_r   <= '0;
+            fifo_wr_en_r <= 1'b0;
+   
+            din_valid_reg <= 1'b0;
+        end else begin
+            fifo_wr_en_r  <= 1'b0;
+            acc_din_reg <= acc_din;
+            
+            if (!wr_rst_busy && din_valid_reg) begin
+                fifo_din_r   <= acc_din_reg;
+                fifo_wr_en_r  <= 1'b1;
+            end
+
+            din_valid_reg <= din_valid;
+        end
+    end
+
+    // xpm_fifo_async: Asynchronous FIFO
+    // Xilinx Parameterized Macro, version 2025.1
+
+    xpm_fifo_async #(
+        .DOUT_RESET_VALUE("0"),        // String
+        .FIFO_READ_LATENCY(1),         // DECIMAL
+        .FIFO_WRITE_DEPTH(FIFO_WDEPTH), 
+        .FULL_RESET_VALUE(0),
+        .PROG_EMPTY_THRESH(PACKET_SIZE),
+        .PROG_FULL_THRESH(PACKET_SIZE / (ACCUM_WIDTH / 8)),
+        .RD_DATA_COUNT_WIDTH(RDEPTH_BITS),    
+        .READ_DATA_WIDTH(8),           // always 8 bit for eth
+        .READ_MODE("fwft"),            
+        .SIM_ASSERT_CHK(1),            // DECIMAL; 0=disable simulation messages, 1=enable simulation messages
+        .USE_ADV_FEATURES("1616"),     // String
+        .WRITE_DATA_WIDTH(ACCUM_WIDTH),
+        .WR_DATA_COUNT_WIDTH(WDEPTH_BITS+1)
+    )
+    xpm_fifo_async_inst (
+
+        .data_valid(rd_valid),       // 1-bit output: Read Data Valid: When asserted, this signal indicates that valid data is available on the
+                                        // output bus (dout).
+
+        .dout(m_axis_tdata),
+        .empty(empty), 
+    
+        .full( ),                 
+
+        .prog_full(wr_unavail),         // 1-bit output: Programmable Full: This signal is asserted when the number of words in the FIFO is greater than
+                                        // or equal to the programmable full threshold value. It is de-asserted when the number of words in the FIFO is
+                                        // less than the programmable full threshold value.
+
+        .rd_data_count(rd_data_count), // RD_DATA_COUNT_WIDTH-bit output: Read Data Count: This bus indicates the number of words read from the FIFO.
+
+        .wr_data_count(wr_data_count), // WR_DATA_COUNT_WIDTH-bit output: Write Data Count: This bus indicates the number of words written into the
+                                        // FIFO.
+
+
+
+
+        .rd_clk(eth_clk_in),               // 1-bit input: Read clock: Used for read operation. rd_clk must be a free running clock.
+        .rd_en(rd_en),                 // 1-bit input: Read Enable: If the FIFO is not empty, asserting this signal causes data (on dout) to be read
+                                        // from the FIFO. Must be held active-low when rd_rst_busy is active high.
+
+        .rst(rst),
+        
+        .din(fifo_din_r),                     // WRITE_DATA_WIDTH-bit input: Write Data: The input data bus used when writing the FIFO.
+        .wr_clk(acc_clk_in),               // 1-bit input: Write clock: Used for write operation. wr_clk must be a free running clock.
+        .wr_en(fifo_wr_en_r),
+
+        .wr_rst_busy(wr_rst_busy)
+
+    );
+
+endmodule

rtl/accum/tests/Makefile

@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = accumulator_top
+FPGA_ARCH = artix7
+
+RTL_DIR = ../src
+
+
+include ../../../scripts/vivado.mk
+
+SYN_FILES += $(sort $(shell find ../src -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../src -type f -name '*.xci'))
+
+XDC_FILES += ../../../constraints/ax7a035b.xdc
+XDC_FILES += test_timing.xdc
+
+SYN_FILES += out_axis_fifo_tb.sv
+SYN_FILES += accum_full_tb.sv
+SIM_TOP = tb_accumulator_top
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

rtl/accum/tests/accum_full_tb.sv

@@ -0,0 +1,345 @@
+`timescale 1ns / 1ps
+
+module tb_accumulator_top;
+
+    localparam DATA_WIDTH      = 12;
+    localparam ACCUM_WIDTH     = 32;
+    localparam N_MAX           = 4096;
+    localparam WINDOW_SIZE     = 65;
+    localparam PACKET_SIZE     = 1024;
+    localparam READ_BATCH_SIZE = (PACKET_SIZE*8)/ACCUM_WIDTH;
+    localparam MAX_WORDS       = N_MAX;
+    localparam MAX_SEQ_NUM     = 64;
+
+    logic clk_in;
+    logic eth_clk_in;
+    logic rst;
+
+    logic [DATA_WIDTH-1:0] s_axis_tdata;
+    logic                  s_axis_tvalid;
+    logic                  start;
+    logic [31:0]           smp_num;
+    logic [15:0]           seq_num;
+
+    logic                  req_ready;
+    wire                   send_req;
+
+    wire  [7:0]            m_axis_tdata;
+    wire                   m_axis_tvalid;
+    logic                  m_axis_tready;
+    wire                   m_axis_tlast;
+
+    wire                   finish;
+
+    integer seed;
+    integer total_errors;
+    integer tests_total;
+    integer tests_failed;
+    integer tests_passed;
+
+    integer packets_seen;
+    integer current_packet_byte_count;
+    integer total_words_captured;
+
+    byte packet_bytes [0:PACKET_SIZE-1];
+    logic [ACCUM_WIDTH-1:0] expected_words   [0:MAX_WORDS-1];
+    logic [ACCUM_WIDTH-1:0] captured_words_le[0:MAX_WORDS-1];
+    logic [ACCUM_WIDTH-1:0] captured_words_be[0:MAX_WORDS-1];
+
+    accumulator_top #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .N_MAX(N_MAX),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    ) dut (
+        .clk_in(clk_in),
+        .rst(rst),
+        .s_axis_tdata(s_axis_tdata),
+        .s_axis_tvalid(s_axis_tvalid),
+        .start(start),
+        .smp_num(smp_num),
+        .seq_num(seq_num),
+        .eth_clk_in(eth_clk_in),
+        .req_ready(req_ready),
+        .send_req(send_req),
+        .m_axis_tdata(m_axis_tdata),
+        .m_axis_tvalid(m_axis_tvalid),
+        .m_axis_tready(m_axis_tready),
+        .m_axis_tlast(m_axis_tlast),
+        .finish(finish)
+    );
+
+    initial begin
+        clk_in = 1'b0;
+        forever #5 clk_in = ~clk_in;
+    end
+
+    initial begin
+        eth_clk_in = 1'b0;
+        forever #4 eth_clk_in = ~eth_clk_in;
+    end
+
+    task automatic clear_scoreboard;
+        integer i;
+    begin
+        packets_seen              = 0;
+        current_packet_byte_count = 0;
+        total_words_captured      = 0;
+        for (i = 0; i < MAX_WORDS; i = i + 1) begin
+            expected_words[i]    = '0;
+            captured_words_le[i] = '0;
+            captured_words_be[i] = '0;
+        end
+        for (i = 0; i < PACKET_SIZE; i = i + 1)
+            packet_bytes[i] = 8'h00;
+    end
+    endtask
+
+    task automatic reset_dut;
+    begin
+        rst           = 1'b1;
+        start         = 1'b0;
+        s_axis_tdata  = '0;
+        s_axis_tvalid = 1'b0;
+        smp_num       = '0;
+        seq_num       = '0;
+        req_ready     = 1'b0;
+        m_axis_tready = 1'b1;
+        clear_scoreboard();
+
+        repeat(12) @(posedge clk_in);
+        rst = 1'b0;
+        repeat(8) @(posedge clk_in);
+    end
+    endtask
+
+    task automatic pulse_start;
+    begin
+        @(posedge clk_in);
+        start <= 1'b1;
+        @(posedge clk_in);
+        start <= 1'b0;
+    end
+    endtask
+
+    task automatic send_one_sample(input logic [DATA_WIDTH-1:0] val);
+    begin
+        @(posedge clk_in);
+        s_axis_tdata  <= val;
+        s_axis_tvalid <= 1'b1;
+    end
+    endtask
+
+    task automatic stop_stream;
+    begin
+        @(posedge clk_in);
+        s_axis_tdata  <= '0;
+        s_axis_tvalid <= 1'b0;
+    end
+    endtask
+
+    task automatic run_test(
+        input integer test_id,
+        input integer seq_num_i,
+        input integer smp_num_i,
+        input bit     randomize_data,
+        input integer base_value,
+        input string  test_name
+    );
+        logic [DATA_WIDTH-1:0] sample_mem [0:MAX_SEQ_NUM-1][0:(N_MAX*WINDOW_SIZE)-1];
+        integer seq_idx;
+        integer sample_idx;
+        integer word_idx;
+        integer k;
+        integer exp_word_count;
+        integer exp_packet_count;
+        integer sample_value;
+        integer local_sum;
+        integer timeout_cnt;
+        bit le_ok;
+        bit be_ok;
+        integer errors_before;
+        integer i;
+    begin
+        tests_total   = tests_total + 1;
+        errors_before = total_errors;
+
+        if (smp_num_i <= 0 || smp_num_i > N_MAX * WINDOW_SIZE || (smp_num_i % WINDOW_SIZE) != 0)
+            $fatal(1, "[%0s] invalid smp_num=%0d", test_name, smp_num_i);
+        if (seq_num_i <= 0 || seq_num_i > MAX_SEQ_NUM)
+            $fatal(1, "[%0s] invalid seq_num=%0d", test_name, seq_num_i);
+
+        $display("\n========================================");
+        $display("TEST %0d: %0s", test_id, test_name);
+        $display("seq_num=%0d smp_num=%0d randomize=%0d", seq_num_i, smp_num_i, randomize_data);
+        $display("========================================");
+
+        reset_dut();
+        smp_num   = smp_num_i;
+        seq_num   = seq_num_i;
+        req_ready = 1'b1; // приемник готов заранее
+
+        exp_word_count   = smp_num_i / WINDOW_SIZE;
+        exp_packet_count = (exp_word_count + READ_BATCH_SIZE - 1) / READ_BATCH_SIZE;
+
+        for (seq_idx = 0; seq_idx < seq_num_i; seq_idx = seq_idx + 1) begin
+            for (sample_idx = 0; sample_idx < smp_num_i; sample_idx = sample_idx + 1) begin
+                if (randomize_data)
+                    sample_value = $unsigned($random(seed)) % (1 << DATA_WIDTH);
+                else
+                    sample_value = (base_value + seq_idx * smp_num_i + sample_idx) % (1 << DATA_WIDTH);
+                sample_mem[seq_idx][sample_idx] = sample_value[DATA_WIDTH-1:0];
+            end
+        end
+
+        for (word_idx = 0; word_idx < exp_word_count; word_idx = word_idx + 1) begin
+            local_sum = 0;
+            for (seq_idx = 0; seq_idx < seq_num_i; seq_idx = seq_idx + 1) begin
+                for (k = 0; k < WINDOW_SIZE; k = k + 1)
+                    local_sum = local_sum + sample_mem[seq_idx][word_idx * WINDOW_SIZE + k];
+            end
+            expected_words[word_idx] = local_sum[ACCUM_WIDTH-1:0];
+            $display("  expected[%0d] = %0d (0x%08x)", word_idx, expected_words[word_idx], expected_words[word_idx]);
+        end
+
+        pulse_start();
+
+        for (seq_idx = 0; seq_idx < seq_num_i; seq_idx = seq_idx + 1) begin
+            for (sample_idx = 0; sample_idx < smp_num_i; sample_idx = sample_idx + 1)
+                send_one_sample(sample_mem[seq_idx][sample_idx]);
+            stop_stream();
+            repeat(2) @(posedge clk_in);
+        end
+
+        timeout_cnt = 0;
+        while (packets_seen < exp_packet_count && timeout_cnt < 50 * PACKET_SIZE) begin
+            @(posedge eth_clk_in);
+            timeout_cnt = timeout_cnt + 1;
+        end
+        if (packets_seen < exp_packet_count) begin
+            $display("[%0s] ERROR: timeout waiting packets, got=%0d exp=%0d",
+                     test_name, packets_seen, exp_packet_count);
+            total_errors = total_errors + 1;
+        end
+
+        timeout_cnt = 0;
+        while (finish !== 1'b1 && timeout_cnt < 30000) begin
+            @(posedge clk_in);
+            timeout_cnt = timeout_cnt + 1;
+        end
+        if (finish !== 1'b1) begin
+            $display("[%0s] ERROR: timeout waiting finish", test_name);
+            total_errors = total_errors + 1;
+        end
+
+        le_ok = 1'b1;
+        be_ok = 1'b1;
+        for (i = 0; i < exp_word_count; i = i + 1) begin
+            if (captured_words_le[i] !== expected_words[i]) le_ok = 1'b0;
+            if (captured_words_be[i] !== expected_words[i]) be_ok = 1'b0;
+        end
+
+        if (!le_ok && !be_ok) begin
+            $display("[%0s] ERROR: payload mismatch", test_name);
+            for (i = 0; i < exp_word_count; i = i + 1)
+                $display("  idx=%0d exp=0x%08x le=0x%08x be=0x%08x",
+                         i, expected_words[i], captured_words_le[i], captured_words_be[i]);
+            total_errors = total_errors + 1;
+        end else if (le_ok) begin
+            $display("[%0s] payload check passed in little-endian", test_name);
+        end else begin
+            $display("[%0s] payload check passed in big-endian", test_name);
+        end
+
+        if (total_errors == errors_before) begin
+            tests_passed = tests_passed + 1;
+            $display("TEST %0d PASSED: %0s", test_id, test_name);
+        end else begin
+            tests_failed = tests_failed + 1;
+            $display("TEST %0d FAILED: %0s", test_id, test_name);
+        end
+
+        req_ready = 1'b0;
+        repeat(10) @(posedge clk_in);
+    end
+    endtask
+
+    always @(posedge eth_clk_in) begin : CAPTURE_AXIS
+        integer idx;
+        logic [31:0] tmp_le;
+        logic [31:0] tmp_be;
+        if (rst) begin
+            current_packet_byte_count = 0;
+        end else if (m_axis_tvalid && m_axis_tready) begin
+            if (current_packet_byte_count < PACKET_SIZE)
+                packet_bytes[current_packet_byte_count] = m_axis_tdata;
+            current_packet_byte_count = current_packet_byte_count + 1;
+
+            if (m_axis_tlast) begin
+                packets_seen = packets_seen + 1;
+
+                if (current_packet_byte_count != PACKET_SIZE) begin
+                    $display("[packet] ERROR: packet size=%0d expected=%0d", current_packet_byte_count, PACKET_SIZE);
+                    total_errors = total_errors + 1;
+                end
+
+                for (idx = 0; idx < READ_BATCH_SIZE; idx = idx + 1) begin
+                    tmp_le = {
+                        packet_bytes[idx*4 + 3],
+                        packet_bytes[idx*4 + 2],
+                        packet_bytes[idx*4 + 1],
+                        packet_bytes[idx*4 + 0]
+                    };
+                    tmp_be = {
+                        packet_bytes[idx*4 + 0],
+                        packet_bytes[idx*4 + 1],
+                        packet_bytes[idx*4 + 2],
+                        packet_bytes[idx*4 + 3]
+                    };
+                    if (total_words_captured + idx < MAX_WORDS) begin
+                        captured_words_le[total_words_captured + idx] = tmp_le;
+                        captured_words_be[total_words_captured + idx] = tmp_be;
+                    end
+                end
+
+                total_words_captured      = total_words_captured + READ_BATCH_SIZE;
+                current_packet_byte_count = 0;
+            end
+        end
+    end
+
+    initial begin
+        seed        = 32'h1badf00d;
+        total_errors = 0;
+        tests_total  = 0;
+        tests_failed = 0;
+        tests_passed = 0;
+
+        reset_dut();
+
+        run_test(1, 1,  1 * WINDOW_SIZE, 1'b0, 1,  "deterministic_small");
+//        $finish;
+        run_test(2, 2,  1 * WINDOW_SIZE, 1'b1, 0,  "random_seq3_smp8");
+        run_test(3, 1, 16 * WINDOW_SIZE, 1'b1, 0,  "random_seq5_smp16_multi_packet");
+        run_test(4, 2, 12 * WINDOW_SIZE, 1'b1, 0,  "random_seq7_smp12");
+        run_test(5, 4, 256 * WINDOW_SIZE, 1'b1, 0,  "random_max_smpnum");
+        run_test(6, 2, 1500 * WINDOW_SIZE, 1'b1, 0,  "random_max_smpnum2");
+
+        $display("\n========================================");
+        $display("ALL TESTS COMPLETED");
+        $display("tests_total  = %0d", tests_total);
+        $display("tests_passed = %0d", tests_passed);
+        $display("tests_failed = %0d", tests_failed);
+        $display("total_errors = %0d", total_errors);
+        $display("========================================");
+
+        if (total_errors != 0)
+            $fatal(1, "TB FAILED with %0d error(s)", total_errors);
+        else
+            $display("TB PASSED");
+
+        $finish;
+    end
+
+endmodule

rtl/accum/tests/accum_tb.sv

@@ -0,0 +1,183 @@
+`timescale 1ns / 1ps
+
+module tb_accumulator;
+
+    localparam DATA_WIDTH    = 12;
+    localparam ACCUM_WIDTH   = 32;
+    localparam N_MAX         = 64;
+    localparam WINDOW_SIZE   = 4;
+    localparam PACKET_SIZE   = 8;   // bytes
+    localparam READ_BATCH_SIZE = (PACKET_SIZE*8)/ACCUM_WIDTH; // = 2
+
+    reg clk_in;
+    reg rst;
+    reg [DATA_WIDTH-1:0] s_axis_tdata;
+    reg s_axis_tvalid;
+    reg start;
+    reg [31:0] smp_num;
+    reg [15:0] seq_num;
+    wire [ACCUM_WIDTH-1:0] out_data;
+    wire out_valid;
+    wire readout_begin;
+    reg batch_req;
+    reg finish;
+
+    integer i;
+    integer out_count;
+
+    reg [ACCUM_WIDTH-1:0] expected [0:READ_BATCH_SIZE-1];
+    reg [ACCUM_WIDTH-1:0] got      [0:READ_BATCH_SIZE-1];
+
+    accumulator #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .N_MAX(N_MAX),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    ) dut (
+        .clk_in(clk_in),
+        .rst(rst),
+        .s_axis_tdata(s_axis_tdata),
+        .s_axis_tvalid(s_axis_tvalid),
+        .start(start),
+        .smp_num(smp_num),
+        .seq_num(seq_num),
+        .out_data(out_data),
+        .out_valid(out_valid),
+        .readout_begin(readout_begin),
+        .batch_req(batch_req),
+        .finish(finish)
+    );
+
+    // clock 100 MHz
+    initial begin
+        clk_in = 0;
+        forever #5 clk_in = ~clk_in;
+    end
+
+    // send one sample
+    task send_sample(input [DATA_WIDTH-1:0] val);
+    begin
+        @(posedge clk_in);
+        s_axis_tdata  <= val;
+        s_axis_tvalid <= 1'b1;
+    end
+    endtask
+
+    // one idle cycle after valid stream
+    task end_stream;
+    begin
+        @(posedge clk_in);
+        s_axis_tvalid <= 1'b0;
+        s_axis_tdata  <= '0;
+    end
+    endtask
+
+    // pulse start
+    task pulse_start;
+    begin
+        @(posedge clk_in);
+        start <= 1'b1;
+        @(posedge clk_in);
+        start <= 1'b0;
+    end
+    endtask
+
+    // pulse batch request
+    task pulse_batch_req;
+    begin
+        @(posedge clk_in);
+        batch_req <= 1'b1;
+        @(posedge clk_in);
+        batch_req <= 1'b0;
+    end
+    endtask
+
+    initial begin
+        repeat(100) @(posedge clk_in);
+        // init
+        rst          = 1'b1;
+        s_axis_tdata = '0;
+        s_axis_tvalid= 1'b0;
+        start        = 1'b0;
+        smp_num      = 32'd8;
+        seq_num      = 16'd2;
+        batch_req    = 1'b0;
+        finish       = 1'b0;
+
+        expected[0] = 32'd60;
+        expected[1] = 32'd92;
+
+        repeat(50) @(posedge clk_in);
+        rst = 1'b0;
+        repeat(50) @(posedge clk_in);
+
+        $display("=== TEST START ===");
+
+        pulse_start();
+
+        // seq 0: [1..8]
+        send_sample(12'd1);
+        send_sample(12'd2);
+        send_sample(12'd3);
+        send_sample(12'd4);
+        send_sample(12'd5);
+        send_sample(12'd6);
+        send_sample(12'd7);
+        send_sample(12'd8);
+        end_stream();
+
+        // небольшой зазор
+        repeat(5) @(posedge clk_in);
+
+        // seq 1: [11..18]
+        send_sample(12'd11);
+        send_sample(12'd12);
+        send_sample(12'd13);
+        send_sample(12'd14);
+        send_sample(12'd15);
+        send_sample(12'd16);
+        send_sample(12'd17);
+        send_sample(12'd18);
+        end_stream();
+
+        $display("[%0t] all input data sent, waiting readout_begin...", $time);
+
+        wait(readout_begin == 1'b1);
+        $display("[%0t] readout_begin asserted", $time);
+        repeat(22) @(posedge clk_in);
+        pulse_batch_req();
+
+        out_count = 0;
+
+        // ждём два слова
+        while (out_count < READ_BATCH_SIZE) begin
+            @(posedge clk_in);
+            if (out_valid) begin
+                got[out_count] = out_data;
+                $display("[%0t] out_valid: got[%0d] = %0d", $time, out_count, out_data);
+                out_count = out_count + 1;
+            end
+        end
+
+        // проверка
+        for (i = 0; i < READ_BATCH_SIZE; i = i + 1) begin
+            if (got[i] !== expected[i]) begin
+                $error("Mismatch at index %0d: got=%0d expected=%0d", i, got[i], expected[i]);
+            end else begin
+                $display("OK index %0d: %0d", i, got[i]);
+            end
+        end
+
+        // завершаем readout
+        @(posedge clk_in);
+        finish <= 1'b1;
+
+
+        repeat(10) @(posedge clk_in);
+
+        $display("=== TEST PASSED ===");
+        $finish;
+    end
+
+endmodule

rtl/accum/tests/out_axis_fifo_tb.sv

@@ -0,0 +1,290 @@
+`timescale 1ns/1ps
+
+module tb_out_axis_fifo;
+
+    localparam int ACCUM_WIDTH = 32;
+    localparam int WINDOW_SIZE = 65;
+    localparam int PACKET_SIZE = 8;
+    localparam int BYTES_PER_WORD = ACCUM_WIDTH / 8;
+    localparam int WORDS_PER_BATCH = PACKET_SIZE / BYTES_PER_WORD; // 1024 / 4 = 256 слов
+
+    logic eth_clk_in;
+    logic acc_clk_in;
+    logic rst;
+
+    logic [31:0] smp_num;
+
+    logic [7:0]  m_axis_tdata;
+    logic        m_axis_tvalid;
+    logic        m_axis_tready;
+    logic        m_axis_tlast;
+
+    logic [ACCUM_WIDTH-1:0] acc_din;
+    logic                   din_valid;
+
+    logic send_req;
+    logic req_ready;
+
+    logic readout_begin;
+
+    logic batch_req;
+    logic finish;
+
+    out_axis_fifo #(
+        .ACCUM_WIDTH(ACCUM_WIDTH),
+        .WINDOW_SIZE(WINDOW_SIZE),
+        .PACKET_SIZE(PACKET_SIZE)
+    ) dut (
+        .eth_clk_in    (eth_clk_in),
+        .acc_clk_in    (acc_clk_in),
+        .rst           (rst),
+        .smp_num       (smp_num),
+
+        .m_axis_tdata  (m_axis_tdata),
+        .m_axis_tvalid (m_axis_tvalid),
+        .m_axis_tready (m_axis_tready),
+        .m_axis_tlast  (m_axis_tlast),
+
+        .acc_din       (acc_din),
+        .din_valid     (din_valid),
+
+        .readout_begin (readout_begin),
+
+        .req_ready     (req_ready),
+        .send_req      (send_req),
+
+        .batch_req     (batch_req),
+        .finish        (finish)
+    );
+
+    // clocks
+    initial begin
+        eth_clk_in = 0;
+        forever #6 eth_clk_in = ~eth_clk_in;   // 125
+    end
+
+    initial begin
+        acc_clk_in = 0;
+        forever #7.692307692 acc_clk_in = ~acc_clk_in;   // 65
+    end
+
+    // scoreboard
+    byte expected_bytes[$];
+    int unsigned compared_bytes;
+    int unsigned mismatch_count;
+    int unsigned total_pushed_words;
+
+    task automatic scoreboard_reset();
+        begin
+            expected_bytes.delete();
+            compared_bytes   = 0;
+            mismatch_count   = 0;
+            total_pushed_words = 0;
+        end
+    endtask
+
+    task automatic push_expected_word(input logic [ACCUM_WIDTH-1:0] word);
+        begin
+            // queue push
+            expected_bytes.push_back(word[7:0]);
+            expected_bytes.push_back(word[15:8]);
+            expected_bytes.push_back(word[23:16]);
+            expected_bytes.push_back(word[31:24]);
+            total_pushed_words++;
+        end
+    endtask
+
+    task automatic check_expected_empty(string case_name);
+        begin
+            if (expected_bytes.size() != 0) begin
+                $error("[%0t] %s: expected_bytes is not empty, remaining=%0d",
+                       $time, case_name, expected_bytes.size());
+            end else begin
+                $display("[%0t] %s: scoreboard queue empty, all expected bytes were transmitted",
+                         $time, case_name);
+            end
+        end
+    endtask
+
+    // axis check
+    always_ff @(posedge eth_clk_in or posedge rst) begin
+        byte exp_byte;
+        if (rst) begin
+            compared_bytes <= 0;
+            mismatch_count <= 0;
+        end else begin
+            if (m_axis_tvalid && m_axis_tready) begin
+                if (expected_bytes.size() == 0) begin
+                    $error("[%0t] AXIS produced unexpected byte 0x%02x: expected queue is empty",
+                           $time, m_axis_tdata);
+                    mismatch_count <= mismatch_count + 1;
+                end else begin
+                    exp_byte = expected_bytes.pop_front();
+                    compared_bytes <= compared_bytes + 1;
+
+                    if (m_axis_tdata !== exp_byte) begin
+                        $error("[%0t] AXIS mismatch at byte #%0d: got=0x%02x expected=0x%02x",
+                               $time, compared_bytes, m_axis_tdata, exp_byte);
+                        mismatch_count <= mismatch_count + 1;
+                    end
+                end
+            end
+        end
+    end
+
+    // helpers
+    task automatic do_reset();
+        begin
+            rst           = 1'b1;
+            readout_begin = 1'b0;
+            din_valid     = 1'b0;
+            acc_din       = '0;
+            smp_num       = '0;
+
+            scoreboard_reset();
+
+            repeat (10) @(posedge acc_clk_in);
+            rst = 1'b0;
+
+            repeat (10) @(posedge acc_clk_in);
+        end
+    endtask
+
+    task automatic pulse_readout_begin(input logic [31:0] smp_num_i);
+        begin
+            smp_num = smp_num_i;
+            @(posedge acc_clk_in);
+            readout_begin <= 1'b1;
+            @(posedge acc_clk_in);
+            readout_begin <= 1'b0;
+        end
+    endtask
+
+    task automatic send_random_words(input int unsigned n_words);
+        int unsigned i;
+        logic [ACCUM_WIDTH-1:0] rand_word;
+        begin
+            for (i = 0; i < n_words; i++) begin
+                rand_word = $urandom;
+
+                @(posedge acc_clk_in);
+                din_valid <= 1'b1;
+                acc_din   <= rand_word;
+
+                // expected result
+                push_expected_word(rand_word);
+            end
+
+            @(posedge acc_clk_in);
+            din_valid <= 1'b0;
+            acc_din   <= '0;
+        end
+    endtask
+
+
+    // 1. set smp_num
+    // 2. pulse readout_begon
+    // 3. send 1KB (PACKET_SIZE) after each batch_req pulse
+    // 4. wait for finish
+    // 5. compare axis result
+    task automatic run_case(input logic [31:0] smp_num_i);
+        int batch_count;
+        string case_name;
+        begin
+            batch_count = 0;
+            case_name = $sformatf("run_case(smp_num=%0d)", smp_num_i);
+
+            $display("[%0t] %s start", $time, case_name);
+
+            pulse_readout_begin(smp_num_i);
+
+            while (finish !== 1'b1) begin
+                @(posedge acc_clk_in);
+
+                if (batch_req) begin
+                    batch_count++;
+                    $display("[%0t] %s: batch_req #%0d -> send %0d words",
+                             $time, case_name, batch_count, WORDS_PER_BATCH);
+
+                    send_random_words(WORDS_PER_BATCH);
+                end
+            end
+
+
+            repeat (200) @(posedge eth_clk_in);
+
+            $display("[%0t] %s done: batches=%0d, pushed_words=%0d, compared_bytes=%0d, mismatches=%0d, wr_cnt=%0d, wr_total=%0d",
+                     $time, case_name, batch_count, total_pushed_words, compared_bytes, mismatch_count,
+                     dut.wr_cnt, dut.wr_total);
+
+            check_expected_empty(case_name);
+
+            if (mismatch_count != 0) begin
+                $fatal(1, "[%0t] %s FAILED: mismatches=%0d", $time, case_name, mismatch_count);
+            end else begin
+                $display("[%0t] %s PASSED", $time, case_name);
+            end
+
+            @(posedge acc_clk_in);
+        end
+    endtask
+
+    // eth beh simulator
+    int axis_byte_count;
+
+    always_ff @(posedge eth_clk_in or posedge rst) begin
+        if (rst) begin
+            axis_byte_count <= 0;
+            req_ready       <= 0;
+            m_axis_tready   <= 1'b0;
+        end else begin
+            req_ready <= 1;
+
+            // request send
+            if (send_req) begin
+                m_axis_tready <= 1'b1;
+                req_ready <= 0;
+            end
+
+            if (m_axis_tvalid && m_axis_tready) begin
+                axis_byte_count <= axis_byte_count + 1;
+            end
+        end
+    end
+
+
+    // main
+    initial begin
+        // init
+        rst           = 1'b0;
+        readout_begin = 1'b0;
+        din_valid     = 1'b0;
+        acc_din       = '0;
+        smp_num       = '0;
+
+        repeat (500) @(posedge acc_clk_in);
+
+        // 1
+        do_reset();
+        repeat (500) @(posedge acc_clk_in);
+        run_case(32'd17);
+        repeat (20) @(posedge acc_clk_in);
+
+        // 2
+        do_reset();
+        run_case(32'd1024);
+        repeat (20) @(posedge acc_clk_in);
+
+        // 3
+        do_reset();
+        run_case(32'd77777);
+        repeat (20) @(posedge acc_clk_in);
+
+        do_reset();
+        repeat (20) @(posedge acc_clk_in);
+
+        $display("[%0t] ALL TESTS DONE", $time);
+        $finish;
+    end
+
+endmodule

rtl/accum/tests/tb_accumulator_top_behav.wcfg

@@ -0,0 +1,179 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<wave_config>
+   <wave_state>
+   </wave_state>
+   <db_ref_list>
+      <db_ref path="tb_accumulator_top_behav.wdb" id="1">
+         <top_modules>
+            <top_module name="glbl" />
+            <top_module name="tb_accumulator_top" />
+         </top_modules>
+      </db_ref>
+   </db_ref_list>
+   <zoom_setting>
+      <ZoomStartTime time="0.000000 us"></ZoomStartTime>
+      <ZoomEndTime time="16.740001 us"></ZoomEndTime>
+      <Cursor1Time time="6.500000 us"></Cursor1Time>
+   </zoom_setting>
+   <column_width_setting>
+      <NameColumnWidth column_width="556"></NameColumnWidth>
+      <ValueColumnWidth column_width="111"></ValueColumnWidth>
+   </column_width_setting>
+   <WVObjectSize size="18" />
+   <wvobject type="logic" fp_name="/tb_accumulator_top/clk_in">
+      <obj_property name="ElementShortName">clk_in</obj_property>
+      <obj_property name="ObjectShortName">clk_in</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/eth_clk_in">
+      <obj_property name="ElementShortName">eth_clk_in</obj_property>
+      <obj_property name="ObjectShortName">eth_clk_in</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/rst">
+      <obj_property name="ElementShortName">rst</obj_property>
+      <obj_property name="ObjectShortName">rst</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_accumulator_top/s_axis_tdata">
+      <obj_property name="ElementShortName">s_axis_tdata[11:0]</obj_property>
+      <obj_property name="ObjectShortName">s_axis_tdata[11:0]</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/s_axis_tvalid">
+      <obj_property name="ElementShortName">s_axis_tvalid</obj_property>
+      <obj_property name="ObjectShortName">s_axis_tvalid</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/start">
+      <obj_property name="ElementShortName">start</obj_property>
+      <obj_property name="ObjectShortName">start</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_accumulator_top/smp_num">
+      <obj_property name="ElementShortName">smp_num[31:0]</obj_property>
+      <obj_property name="ObjectShortName">smp_num[31:0]</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_accumulator_top/seq_num">
+      <obj_property name="ElementShortName">seq_num[15:0]</obj_property>
+      <obj_property name="ObjectShortName">seq_num[15:0]</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/req_ready">
+      <obj_property name="ElementShortName">req_ready</obj_property>
+      <obj_property name="ObjectShortName">req_ready</obj_property>
+      <obj_property name="CustomSignalColor">#E0FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/send_req">
+      <obj_property name="ElementShortName">send_req</obj_property>
+      <obj_property name="ObjectShortName">send_req</obj_property>
+      <obj_property name="CustomSignalColor">#E0FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_accumulator_top/m_axis_tdata">
+      <obj_property name="ElementShortName">m_axis_tdata[7:0]</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tdata[7:0]</obj_property>
+      <obj_property name="CustomSignalColor">#008080</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/m_axis_tready">
+      <obj_property name="ElementShortName">m_axis_tready</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tready</obj_property>
+      <obj_property name="CustomSignalColor">#00FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/m_axis_tlast">
+      <obj_property name="ElementShortName">m_axis_tlast</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tlast</obj_property>
+      <obj_property name="CustomSignalColor">#008080</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/finish">
+      <obj_property name="ElementShortName">finish</obj_property>
+      <obj_property name="ObjectShortName">finish</obj_property>
+      <obj_property name="CustomSignalColor">#FAAFBE</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/dut/batch_req">
+      <obj_property name="ElementShortName">batch_req</obj_property>
+      <obj_property name="ObjectShortName">batch_req</obj_property>
+      <obj_property name="CustomSignalColor">#00FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_accumulator_top/dut/readout_begin">
+      <obj_property name="ElementShortName">readout_begin</obj_property>
+      <obj_property name="ObjectShortName">readout_begin</obj_property>
+      <obj_property name="CustomSignalColor">#00FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="group" fp_name="group25">
+      <obj_property name="label">acc</obj_property>
+      <obj_property name="DisplayName">label</obj_property>
+      <obj_property name="isExpanded"></obj_property>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/accum_main/PACKET_SIZE">
+         <obj_property name="ElementShortName">PACKET_SIZE[31:0]</obj_property>
+         <obj_property name="ObjectShortName">PACKET_SIZE[31:0]</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/accum_main/READ_BATCH_SIZE">
+         <obj_property name="ElementShortName">READ_BATCH_SIZE[31:0]</obj_property>
+         <obj_property name="ObjectShortName">READ_BATCH_SIZE[31:0]</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/accum_main/addrb">
+         <obj_property name="ElementShortName">addrb[15:0]</obj_property>
+         <obj_property name="ObjectShortName">addrb[15:0]</obj_property>
+      </wvobject>
+   </wvobject>
+   <wvobject type="group" fp_name="group27">
+      <obj_property name="label">fifo</obj_property>
+      <obj_property name="DisplayName">label</obj_property>
+      <obj_property name="isExpanded"></obj_property>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/acc_din">
+         <obj_property name="ElementShortName">acc_din[31:0]</obj_property>
+         <obj_property name="ObjectShortName">acc_din[31:0]</obj_property>
+         <obj_property name="CustomSignalColor">#FF0080</obj_property>
+         <obj_property name="UseCustomSignalColor">true</obj_property>
+      </wvobject>
+      <wvobject type="logic" fp_name="/tb_accumulator_top/dut/output_async_fifo/din_valid">
+         <obj_property name="ElementShortName">din_valid</obj_property>
+         <obj_property name="ObjectShortName">din_valid</obj_property>
+         <obj_property name="CustomSignalColor">#FF0080</obj_property>
+         <obj_property name="UseCustomSignalColor">true</obj_property>
+      </wvobject>
+      <wvobject type="logic" fp_name="/tb_accumulator_top/dut/output_async_fifo/batch_req">
+         <obj_property name="ElementShortName">batch_req</obj_property>
+         <obj_property name="ObjectShortName">batch_req</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/wr_state">
+         <obj_property name="ElementShortName">wr_state[2:0]</obj_property>
+         <obj_property name="ObjectShortName">wr_state[2:0]</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/rd_state">
+         <obj_property name="ElementShortName">rd_state[2:0]</obj_property>
+         <obj_property name="ObjectShortName">rd_state[2:0]</obj_property>
+      </wvobject>
+      <wvobject type="logic" fp_name="/tb_accumulator_top/dut/output_async_fifo/wr_unavail">
+         <obj_property name="ElementShortName">wr_unavail</obj_property>
+         <obj_property name="ObjectShortName">wr_unavail</obj_property>
+         <obj_property name="CustomSignalColor">#FFFF00</obj_property>
+         <obj_property name="UseCustomSignalColor">true</obj_property>
+      </wvobject>
+      <wvobject type="logic" fp_name="/tb_accumulator_top/dut/output_async_fifo/wr_rst_busy">
+         <obj_property name="ElementShortName">wr_rst_busy</obj_property>
+         <obj_property name="ObjectShortName">wr_rst_busy</obj_property>
+         <obj_property name="CustomSignalColor">#FFFF00</obj_property>
+         <obj_property name="UseCustomSignalColor">true</obj_property>
+      </wvobject>
+      <wvobject type="logic" fp_name="/tb_accumulator_top/dut/output_async_fifo/xpm_fifo_async_inst/empty">
+         <obj_property name="ElementShortName">empty</obj_property>
+         <obj_property name="ObjectShortName">empty</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/xpm_fifo_async_inst/PROG_FULL_THRESH">
+         <obj_property name="ElementShortName">PROG_FULL_THRESH[31:0]</obj_property>
+         <obj_property name="ObjectShortName">PROG_FULL_THRESH[31:0]</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/xpm_fifo_async_inst/wr_data_count">
+         <obj_property name="ElementShortName">wr_data_count[4:0]</obj_property>
+         <obj_property name="ObjectShortName">wr_data_count[4:0]</obj_property>
+         <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+      </wvobject>
+      <wvobject type="array" fp_name="/tb_accumulator_top/dut/output_async_fifo/xpm_fifo_async_inst/rd_data_count">
+         <obj_property name="ElementShortName">rd_data_count[6:0]</obj_property>
+         <obj_property name="ObjectShortName">rd_data_count[6:0]</obj_property>
+         <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+      </wvobject>
+   </wvobject>
+</wave_config>

rtl/accum/tests/tb_out_axis_fifo_behav.wcfg

@@ -0,0 +1,196 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<wave_config>
+   <wave_state>
+   </wave_state>
+   <db_ref_list>
+      <db_ref path="tb_out_axis_fifo_behav.wdb" id="1">
+         <top_modules>
+            <top_module name="glbl" />
+            <top_module name="tb_out_axis_fifo" />
+         </top_modules>
+      </db_ref>
+   </db_ref_list>
+   <zoom_setting>
+      <ZoomStartTime time="18,433.000 ns"></ZoomStartTime>
+      <ZoomEndTime time="24,238.001 ns"></ZoomEndTime>
+      <Cursor1Time time="21,618.000 ns"></Cursor1Time>
+   </zoom_setting>
+   <column_width_setting>
+      <NameColumnWidth column_width="196"></NameColumnWidth>
+      <ValueColumnWidth column_width="147"></ValueColumnWidth>
+   </column_width_setting>
+   <WVObjectSize size="37" />
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/eth_clk_in">
+      <obj_property name="ElementShortName">eth_clk_in</obj_property>
+      <obj_property name="ObjectShortName">eth_clk_in</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/acc_clk_in">
+      <obj_property name="ElementShortName">acc_clk_in</obj_property>
+      <obj_property name="ObjectShortName">acc_clk_in</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/rst">
+      <obj_property name="ElementShortName">rst</obj_property>
+      <obj_property name="ObjectShortName">rst</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/smp_num">
+      <obj_property name="ElementShortName">smp_num[31:0]</obj_property>
+      <obj_property name="ObjectShortName">smp_num[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/acc_din">
+      <obj_property name="ElementShortName">acc_din[31:0]</obj_property>
+      <obj_property name="ObjectShortName">acc_din[31:0]</obj_property>
+      <obj_property name="CustomSignalColor">#FF0080</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/din_valid">
+      <obj_property name="ElementShortName">din_valid</obj_property>
+      <obj_property name="ObjectShortName">din_valid</obj_property>
+      <obj_property name="CustomSignalColor">#FF0080</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/fifo_din_r">
+      <obj_property name="ElementShortName">fifo_din_r[31:0]</obj_property>
+      <obj_property name="ObjectShortName">fifo_din_r[31:0]</obj_property>
+      <obj_property name="CustomSignalColor">#FFA500</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/fifo_wr_en_r">
+      <obj_property name="ElementShortName">fifo_wr_en_r</obj_property>
+      <obj_property name="ObjectShortName">fifo_wr_en_r</obj_property>
+      <obj_property name="CustomSignalColor">#FFA500</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/readout_begin">
+      <obj_property name="ElementShortName">readout_begin</obj_property>
+      <obj_property name="ObjectShortName">readout_begin</obj_property>
+      <obj_property name="CustomSignalColor">#FFFF00</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/batch_req">
+      <obj_property name="ElementShortName">batch_req</obj_property>
+      <obj_property name="ObjectShortName">batch_req</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/finish">
+      <obj_property name="ElementShortName">finish</obj_property>
+      <obj_property name="ObjectShortName">finish</obj_property>
+      <obj_property name="CustomSignalColor">#00FFFF</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/m_axis_tdata">
+      <obj_property name="ElementShortName">m_axis_tdata[7:0]</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tdata[7:0]</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/m_axis_tvalid">
+      <obj_property name="ElementShortName">m_axis_tvalid</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tvalid</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/m_axis_tready">
+      <obj_property name="ElementShortName">m_axis_tready</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tready</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/m_axis_tlast">
+      <obj_property name="ElementShortName">m_axis_tlast</obj_property>
+      <obj_property name="ObjectShortName">m_axis_tlast</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/axis_byte_count">
+      <obj_property name="ElementShortName">axis_byte_count[31:0]</obj_property>
+      <obj_property name="ObjectShortName">axis_byte_count[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+      <obj_property name="CustomSignalColor">#F0E68C</obj_property>
+      <obj_property name="UseCustomSignalColor">true</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/ACCUM_WIDTH">
+      <obj_property name="ElementShortName">ACCUM_WIDTH[31:0]</obj_property>
+      <obj_property name="ObjectShortName">ACCUM_WIDTH[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/WINDOW_SIZE">
+      <obj_property name="ElementShortName">WINDOW_SIZE[31:0]</obj_property>
+      <obj_property name="ObjectShortName">WINDOW_SIZE[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/PACKET_SIZE">
+      <obj_property name="ElementShortName">PACKET_SIZE[31:0]</obj_property>
+      <obj_property name="ObjectShortName">PACKET_SIZE[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/wr_state">
+      <obj_property name="ElementShortName">wr_state[2:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_state[2:0]</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/wr_cnt">
+      <obj_property name="ElementShortName">wr_cnt[31:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_cnt[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/wr_batch_tgt">
+      <obj_property name="ElementShortName">wr_batch_tgt[31:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_batch_tgt[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/wr_total">
+      <obj_property name="ElementShortName">wr_total[31:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_total[31:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/prog_empty">
+      <obj_property name="ElementShortName">prog_empty</obj_property>
+      <obj_property name="ObjectShortName">prog_empty</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/prog_full">
+      <obj_property name="ElementShortName">prog_full</obj_property>
+      <obj_property name="ObjectShortName">prog_full</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/wr_ack">
+      <obj_property name="ElementShortName">wr_ack</obj_property>
+      <obj_property name="ObjectShortName">wr_ack</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/wr_data_count">
+      <obj_property name="ElementShortName">wr_data_count[2:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_data_count[2:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/wr_data_count">
+      <obj_property name="ElementShortName">wr_data_count[2:0]</obj_property>
+      <obj_property name="ObjectShortName">wr_data_count[2:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/rd_data_count">
+      <obj_property name="ElementShortName">rd_data_count[4:0]</obj_property>
+      <obj_property name="ObjectShortName">rd_data_count[4:0]</obj_property>
+      <obj_property name="Radix">UNSIGNEDDECRADIX</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/rst_sync_ff">
+      <obj_property name="ElementShortName">rst_sync_ff[1:0]</obj_property>
+      <obj_property name="ObjectShortName">rst_sync_ff[1:0]</obj_property>
+   </wvobject>
+   <wvobject type="array" fp_name="/tb_out_axis_fifo/dut/rd_state">
+      <obj_property name="ElementShortName">rd_state[2:0]</obj_property>
+      <obj_property name="ObjectShortName">rd_state[2:0]</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/rd_en">
+      <obj_property name="ElementShortName">rd_en</obj_property>
+      <obj_property name="ObjectShortName">rd_en</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/rd_valid">
+      <obj_property name="ElementShortName">rd_valid</obj_property>
+      <obj_property name="ObjectShortName">rd_valid</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/overflow">
+      <obj_property name="ElementShortName">overflow</obj_property>
+      <obj_property name="ObjectShortName">overflow</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/dut/xpm_fifo_async_inst/wr_rst_busy">
+      <obj_property name="ElementShortName">wr_rst_busy</obj_property>
+      <obj_property name="ObjectShortName">wr_rst_busy</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/send_req">
+      <obj_property name="ElementShortName">send_req</obj_property>
+      <obj_property name="ObjectShortName">send_req</obj_property>
+   </wvobject>
+   <wvobject type="logic" fp_name="/tb_out_axis_fifo/req_ready">
+      <obj_property name="ElementShortName">req_ready</obj_property>
+      <obj_property name="ObjectShortName">req_ready</obj_property>
+   </wvobject>
+</wave_config>

rtl/accum/tests/test_timing.xdc

@@ -0,0 +1,10 @@
+# Primary clocks
+create_clock -name eth_clk -period 8.000  [get_ports eth_clk_in]
+create_clock -name acc_clk -period 15.385  [get_ports clk_in]
+
+
+# Asynchronous clock groups
+
+set_clock_groups -name ASYNC_ETH_ACC -asynchronous \
+    -group [get_clocks eth_clk] \
+    -group [get_clocks acc_clk]

rtl/sampler/README.md

@@ -0,0 +1,28 @@
+# Сэмплер
+Модуль выполняет задачу сбора данных с выхода АЦП, их обработку, упаковку, и передачу дальше с помощью AXI Stream интерфейса.
+
+## Cписок параметров
+DATA_WIDTH - ширина входных данных, получаемых с АЦП.
+PACK_FACTOR - количество отсчетов, собираемых в один выходной пакет.
+PROCESS_MODE - режим интерпретации входного кода. 0 - прямой код, 1 - дополнительный код.
+
+## Список входных портов
+clk_in - сигнал тактирования выходного интерфейса.
+rst - сброс модуля и остановка подачи импульсов.
+[DATA_WIDTH-1:0] data_in - входной сигнал с АЦП.
+out_of_range - флаг выхода значений данных за допустимый диапазон. 0 - валидны, 1 - не валидны.
+
+## Список выходных портов
+[DATA_WIDTH*PACK_FACTOR-1:0]  m_axis_tdata - урезанный axis формат, выходные данные. Ширина шины считается исходя из битности данных и фактора упаковки.
+m_axis_tvalid - урезанный axis формат, валидность выходных данных.
+
+## Логика работы
+На каждом такте принимаются data_in (значение АЦП) и out_of_range (флаг выхода значений данных за допустимый диапазон). Если out_of_range = 1, то данные игнорируются и не попадают во внутренний буффер. В противном случае, модуль накапливает данные во внутреннем буффере, идет его заполнение до количества данных, равное PACK_FACTOR. Когда буффер оказывается заполненным, он выдает пакет упакованных данных, сопровождая их импульсом m_axis_tvalid (готовность пакета). Если PROCESS_MODE = 1, данные выдаются в дополнительном коде, если PROCESS_MODE = 0 - в прямом.
+
+## Симуляция
+Тесты запускаются автоматически через make.
+```
+cd tests
+make sim
+```
+При успешном завершении теста высвечивается "ALL PASSED".

rtl/sampler/src/sampler.sv

@@ -5,8 +5,8 @@
 module sampler
 #(
     parameter DATA_WIDTH = 12,
-    parameter PACK_FACTOR = 3,
+    parameter PACK_FACTOR = 1,
-    parameter PROCESS_MODE = 1
+    parameter PROCESS_MODE = 0
     )
 (
     input clk_in,
@@ -19,52 +19,103 @@ module sampler
     );
     logic [DATA_WIDTH-1:0] data_converted;
     logic out_of_range_reg;
+    
+    generate
+       if (PROCESS_MODE) begin 
 
-    always @( posedge clk_in) begin
+        always @(posedge clk_in) begin
-        if (rst) begin
+            if (rst) begin
-            data_converted <= '0;
+                data_converted   <= '0;
-        end else begin
+                out_of_range_reg <= 0;
-            out_of_range_reg <= out_of_range;
+            end
-            if (PROCESS_MODE) begin
+            else begin
-                if (data_in == 12'b100000000000) begin
+                out_of_range_reg <= out_of_range;
+                if (data_in == {1'b1, {(DATA_WIDTH-1){1'b0}}})
                     data_converted <= data_in;
-                end else begin
+                else
-                    data_converted <= data_in[DATA_WIDTH-1]  ? {1'b1, (~data_in[DATA_WIDTH-2:0] + 1'b1)} : data_in; 
+                    data_converted <= data_in[DATA_WIDTH-1] ?{1'b1, (~data_in[DATA_WIDTH-2:0] + 1'b1)}:data_in;
-                    
-                end
-            end else begin
-                data_converted <= data_in; 
             end
         end
-    end 
+     end else begin
-    
+        always @(posedge clk_in) begin
+            if (rst) begin
+                data_converted   <= '0;
+                out_of_range_reg <= 0;
+            end
+            else begin
+                out_of_range_reg <= out_of_range;
+                data_converted   <= data_in;
+            end
+        end
+     end
+    endgenerate
          
     logic [DATA_WIDTH*PACK_FACTOR-1:0] buffer;
     logic buffer_ready;
 
     logic [$clog2(PACK_FACTOR):0] cnt;
     
-    always @(posedge clk_in) begin
+    generate
-        if (rst) begin
+      if (PACK_FACTOR == 1) begin
-            buffer <= '0;
+        always @(posedge clk_in) begin
-            cnt <= -1; //
+            if (rst) begin
-            buffer_ready <= 0;
+                buffer       <= '0;
-        end
+                buffer_ready <= 0;
-        else begin
+            end
-            buffer_ready <= 0;
+            else begin
-            if (!out_of_range_reg) begin
+                buffer_ready <= 0;
-                buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+                if (!out_of_range_reg) begin
-                if (cnt == PACK_FACTOR-1) begin
+                    buffer       <= data_converted;
-                    cnt <= 0;
                     buffer_ready <= 1;
-                    buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
-                end
-                else begin
-                    cnt <= cnt + 1;
                 end
             end
         end
-    end
+      end  else begin
+        always @(posedge clk_in) begin
+            if (rst) begin
+                buffer <= '0;
+                cnt <= '0; //
+                buffer_ready <= 0;
+            end
+            else begin
+                buffer_ready <= 0;
+                if (!out_of_range_reg) begin
+                    buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+                    if (cnt == PACK_FACTOR-1) begin
+                        cnt <= 0;
+                        buffer_ready <= 1;
+                        buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+                    end
+                    else begin
+                        cnt <= cnt + 1;
+                    end
+                end
+            end
+        end
+      end
+    endgenerate
+    
+//    always @(posedge clk_in) begin
+//        if (rst) begin
+//            buffer <= '0;
+//            cnt <= '0; //
+//            buffer_ready <= 0;
+//        end
+//        else begin
+//            buffer_ready <= 0;
+//            if (!out_of_range_reg) begin
+//                buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+//                if (cnt == PACK_FACTOR-1) begin
+//                    cnt <= 0;
+//                    buffer_ready <= 1;
+//                    buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+//                end
+//                else begin
+//                    cnt <= cnt + 1;
+//                end
+//            end
+//        end
+//    end
     
     assign m_axis_tdata = buffer;
     assign m_axis_tvalid = buffer_ready;

rtl/sampler/tests/Makefile

@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = sampler
+FPGA_ARCH = artix7
+
+RTL_DIR = ../src
+
+
+include ../../../scripts/vivado.mk
+
+SYN_FILES += $(sort $(shell find ../src -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../src -type f -name '*.xci'))
+
+XDC_FILES += ../../../constraints/ax7a035b.xdc
+
+SYN_FILES += sampler_main_tb.sv
+SIM_TOP = sampler_tb
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

rtl/sampler/tests/sampler_main_tb.sv

@@ -0,0 +1,132 @@
+`timescale 1ns / 1ps
+
+module sampler_tb;
+
+    parameter DATA_WIDTH   = 12;
+    parameter PROCESS_MODE = 0;
+    parameter CLK_PERIOD   = 15.3846;
+    parameter TEST_NUM     = 1000;
+
+    logic clk;
+    logic rst;
+
+    logic [DATA_WIDTH-1:0] data_in;
+    logic out_of_range;
+
+    logic [DATA_WIDTH-1:0] m_axis_tdata;
+    logic m_axis_tvalid;
+
+    integer errors = 0;
+
+    sampler #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .PROCESS_MODE(PROCESS_MODE)
+    ) dut (
+        .clk_in(clk),
+        .rst(rst),
+        .data_in(data_in),
+        .out_of_range(out_of_range),
+        .m_axis_tdata(m_axis_tdata),
+        .m_axis_tvalid(m_axis_tvalid)
+    );
+
+    initial begin
+        clk = 0;
+        forever #(CLK_PERIOD/2) clk = ~clk;
+    end
+
+    function automatic [DATA_WIDTH-1:0] ref_convert(input [DATA_WIDTH-1:0] din);
+        if (PROCESS_MODE == 0)
+            return din;
+        else if (din == {1'b1, {(DATA_WIDTH-1){1'b0}}})
+            return din;
+        else
+            return din[DATA_WIDTH-1] ?
+                   {1'b1, (~din[DATA_WIDTH-2:0] + 1'b1)} :
+                   din;
+    endfunction
+
+    task send(input [DATA_WIDTH-1:0] word, input bit oor);
+        @(posedge clk);
+        data_in      <= word;
+        out_of_range <= oor;
+    endtask
+
+    logic [DATA_WIDTH-1:0] exp_d0, exp_d1, exp_d2;
+    logic oor_d0, oor_d1, oor_d2;
+
+    initial begin
+        $display("\n=== RANDOM SAMPLER TEST===\n");
+
+        rst = 1;
+        data_in = 0;
+        out_of_range = 0;
+
+        exp_d0 = 0;
+        exp_d1 = 0;
+        exp_d2 = 0;
+
+        oor_d0 = 1;
+        oor_d1 = 1;
+        oor_d2 = 1;
+
+        repeat(5) @(posedge clk);
+        rst = 0;
+        repeat(2) @(posedge clk);
+
+        repeat (TEST_NUM) begin
+            logic [DATA_WIDTH-1:0] rand_data;
+            bit rand_oor;
+
+            rand_data = $urandom_range(0, (1 << DATA_WIDTH) - 1);
+            rand_oor  = ($urandom_range(0, 99) < 20);
+
+            @(negedge clk);
+
+            if (!oor_d2) begin
+                if (m_axis_tvalid !== 1) begin
+                    $display("ERROR: valid=0");
+                    errors++;
+                end
+
+                if (m_axis_tdata !== exp_d2) begin
+                    $display("ERROR: data mismatch");
+                    $display(" expected = %h", exp_d2);
+                    $display(" got      = %h", m_axis_tdata);
+                    errors++;
+                end
+            end
+
+            send(rand_data, rand_oor);
+
+            exp_d2 = exp_d1;
+            exp_d1 = exp_d0;
+            exp_d0 = ref_convert(rand_data);
+
+            oor_d2 = oor_d1;
+            oor_d1 = oor_d0;
+            oor_d0 = rand_oor;
+        end
+
+        @(posedge clk);
+
+
+        if (!oor_d2) begin
+        
+            if (m_axis_tdata !== exp_d2) begin
+                $display("ERROR: final mismatch");
+                $display(" expected = %h", exp_d2);
+                $display(" got      = %h", m_axis_tdata);
+                errors++;
+            end
+        end
+
+        if (errors == 0)
+            $display("\n========== ALL PASSED ==========\n");
+        else
+            $display("\n========== FAILED: %0d errors ==========\n", errors);
+
+        $finish;
+    end
+
+endmodule

rtl/sampler/tests/sampler_tb_advanced.sv

@@ -1,120 +0,0 @@
-`timescale 1ns / 1ps
-
-module sampler_tb;
-
-    parameter DATA_WIDTH = 12;
-    parameter PACK_FACTOR = 3;
-    parameter PROCESS_MODE = 1;
-    parameter CLK_PERIOD = 15.3846;  // 65 MHz
-
-    logic clk;
-    logic rst;
-    logic [DATA_WIDTH-1:0] data_in;
-    logic out_of_range;
-    logic [DATA_WIDTH*PACK_FACTOR-1:0] m_axis_tdata;
-    logic m_axis_tvalid;
-
-    sampler #(
-        .DATA_WIDTH(DATA_WIDTH),
-        .PACK_FACTOR(PACK_FACTOR),
-        .PROCESS_MODE(PROCESS_MODE)
-    ) dut (
-        .clk_in(clk),
-        .rst(rst),
-        .data_in(data_in),
-        .out_of_range(out_of_range),
-        .m_axis_tdata(m_axis_tdata),
-        .m_axis_tvalid(m_axis_tvalid)
-    );
-
-    initial begin
-        clk = 0;
-        forever #(CLK_PERIOD/2) clk = ~clk;
-    end
-
-    task send(input [DATA_WIDTH-1:0] word, input bit oor);
-        @(posedge clk);
-        data_in <= word;
-        out_of_range <= oor;
-        $display("Send: %h (%0d) OOR=%b", word, word, oor);
-    endtask
-
-    initial begin
-        $display("\n=== SAMPLER TEST (MODE=%0d) ===\n", PROCESS_MODE);
-        
-        // Reset
-        rst = 1;
-        out_of_range = 0;
-        data_in = 0;
-//        send(12'h001, 0);
-        repeat(5) @(posedge clk);
-        rst = 0;
-        send(12'h001, 0);
-        repeat(1) @(posedge clk);
-        
-        // 1. Positive
-        $display("\n--- Positive numbers ---");
-//        send(12'h001, 0);
-        send(12'h002, 0);
-        send(12'h003, 0);
-        
-        send(12'h004, 0);
-        send(12'h005, 0);
-        send(12'h806, 0);
-        
-        // 2. Negative
-        $display("\n--- Negative numbers ---");
-        send(12'hFFF, 0);  // -1
-        send(12'hFFE, 0);  // -2
-        send(12'hFFD, 0);  // -3
-        
-        send(12'h800, 0);  // -2048
-        send(12'h801, 0);  // -2047
-        send(12'h802, 0);  // -2046
-        
-        // 3. Boundary
-        $display("\n--- Boundary values ---");
-        send(12'h000, 0);  // 0
-        send(12'h001, 0);  // 1
-        send(12'h7FF, 0);  // 2047 (max positive)
-        
-        send(12'h7FE, 0);  // 2046
-        send(12'h800, 0);  // -2048 (min negative)
-        send(12'hFFF, 0);  // -1
-        
-        // 4. Out of range tests
-        $display("\n--- Out of range tests ---");
-        
-
-        send(12'h00A, 0);
-        send(12'h00B, 1);  // 
-        send(12'h00C, 0);
-        send(12'h00D, 0);
-        send(12'h00E, 0);
-        send(12'h00F, 0);  
-        
-        send(12'h010, 0);
-        send(12'h011, 0);
-        send(12'h012, 1);  // 
-        
-        send(12'h013, 0);
-        send(12'h014, 0);
-        send(12'h015, 0); 
-        
-        repeat(10) @(posedge clk);
-        $display("\n=== TEST FINISHED ===");
-        $finish;
-    end
-
-    // Results
-    always @(posedge clk) begin
-        if (m_axis_tvalid) begin
-            $display("\n>>> PACKET RECEIVED at %0t ns:", $time);
-            $display("    Full: %h", m_axis_tdata);
-            $display("    Word0: %h", m_axis_tdata[11:0]);
-            $display("    Word1: %h", m_axis_tdata[23:12]);
-            $display("    Word2: %h\n", m_axis_tdata[35:24]);
-        end
-    end
-
-endmodule

rtl/sampler/tests/sampler_tb_basic.sv

@@ -1,67 +0,0 @@
-`timescale 1ns / 1ps
-
-module sampler_tb;
-
-    parameter DATA_WIDTH = 12;
-    parameter PACK_FACTOR = 3;
-    parameter PROCESS_MODE = 0;
-    
-    parameter CLK_PERIOD = 15.3846; 
-
-    logic clk;
-    logic rst;
-    logic [DATA_WIDTH-1:0] data_in;
-    logic out_of_range;
-
-    logic [DATA_WIDTH*PACK_FACTOR-1:0] m_axis_tdata;
-    logic m_axis_tvalid;
-
-    // DUT
-    sampler #(
-        .DATA_WIDTH(DATA_WIDTH),
-        .PACK_FACTOR(PACK_FACTOR),
-        .PROCESS_MODE(PROCESS_MODE)
-    ) dut (
-        .clk_in(clk),
-        .rst(rst),
-        .data_in(data_in),
-        .out_of_range(out_of_range),
-        .m_axis_tdata(m_axis_tdata),
-        .m_axis_tvalid(m_axis_tvalid)
-    );
-
-    // clock
-     initial begin
-        clk = 0;
-        forever #(CLK_PERIOD/2) clk = ~clk;
-    end
-
-    integer i;
-
-    initial begin
-        clk = 0;
-        rst = 1;
-        data_in = 0;
-        out_of_range = 0;
-
-        #20;
-        rst = 0;
-        repeat(5) @(posedge clk);
-
-        for (i = 1; i < 20; i++) begin
-            @(posedge clk);
-
-            data_in <= i;
-        end
-
-        #50;
-        $finish;
-    end
-
-    always @(posedge clk) begin
-        if (m_axis_tvalid) begin
-            $display("TIME=%0t PACKED DATA = %h", $time, m_axis_tdata);
-        end
-    end
-
-endmodule

scripts/vivado.mk

@@ -180,6 +180,8 @@ sim: $(PROJECT).xpr gen_ip
 	echo "update_compile_order -fileset sources_1" >> run_sim.tcl
 	echo "update_compile_order -fileset sim_1" >> run_sim.tcl
 	echo "launch_simulation" >> run_sim.tcl
+	echo "run 10000 us" >> run_sim.tcl
+	echo "quit" >> run_sim.tcl
 	vivado -mode batch -source run_sim.tcl
 
 simclean: