Merge pull request 'dev/debug' (#6) from dev/debug into master

Reviewed-on: #6

.gitignore

@@ -1 +1,29 @@
 **build**
+
+# vivado project exclude
+**.hw
+**.ip_user_files
+**.cache
+**.gen
+**.runs
+**.sim
+**.srcs
+*.jou
+*.log
+*.rpt
+*.dcp
+*.xpr
+.Xil
+xvlog.pb
+*vivado_pid*
+
+# some generated files (they annoy me)
+update_config.tcl
+create_project.tcl
+gen_ip.tcl
+defines.v
+run_sim.tcl
+*.bit
+*.xsa
+*.ltx
+*.bin

constraints/ax7a035b.xdc

@@ -0,0 +1,97 @@
+# === iostandard ===
+set_property CFGBVS VCCO [current_design]
+set_property CONFIG_VOLTAGE 3.3 [current_design]
+
+# === SPI flash config ===
+set_property BITSTREAM.CONFIG.SPI_BUSWIDTH 4 [current_design]
+set_property CONFIG_MODE SPIx4 [current_design]
+set_property BITSTREAM.CONFIG.CONFIGRATE 50 [current_design]
+
+# === clock config ===
+create_clock -period 5.000 [get_ports sys_clk_p]
+set_property IOSTANDARD DIFF_SSTL15 [get_ports sys_clk_p]
+set_property PACKAGE_PIN R4 [get_ports sys_clk_p]
+set_property PACKAGE_PIN T4 [get_ports sys_clk_n]
+set_property IOSTANDARD DIFF_SSTL15 [get_ports sys_clk_n]
+
+
+# === reset button ===
+set_property PACKAGE_PIN F15 [get_ports rst_n]
+set_property IOSTANDARD LVCMOS33 [get_ports rst_n]
+
+# === status leds ===
+set_property PACKAGE_PIN L13 [get_ports {led[0]}]
+set_property PACKAGE_PIN M13 [get_ports {led[1]}]
+set_property PACKAGE_PIN K14 [get_ports {led[2]}]
+set_property PACKAGE_PIN K13 [get_ports {led[3]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {led[*]}]
+
+# === 1Gb ethernet PHY ===
+set_property PACKAGE_PIN P15 [get_ports rgmii_txc]
+set_property PACKAGE_PIN N14 [get_ports {rgmii_txd[0]}]
+set_property PACKAGE_PIN P16 [get_ports {rgmii_txd[1]}]
+set_property PACKAGE_PIN R17 [get_ports {rgmii_txd[2]}]
+set_property PACKAGE_PIN R16 [get_ports {rgmii_txd[3]}]
+set_property PACKAGE_PIN N17 [get_ports rgmii_txctl]
+set_property PACKAGE_PIN V18 [get_ports rgmii_rxc]
+set_property PACKAGE_PIN P19 [get_ports {rgmii_rxd[0]}]
+set_property PACKAGE_PIN U18 [get_ports {rgmii_rxd[1]}]
+set_property PACKAGE_PIN U17 [get_ports {rgmii_rxd[2]}]
+set_property PACKAGE_PIN P17 [get_ports {rgmii_rxd[3]}]
+set_property PACKAGE_PIN R19 [get_ports rgmii_rxctl]
+set_property PACKAGE_PIN N13 [get_ports e_mdc]
+set_property PACKAGE_PIN P14 [get_ports e_mdio]
+set_property PACKAGE_PIN R14 [get_ports e_reset]
+
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_txc]
+set_property IOSTANDARD LVCMOS33 [get_ports {rgmii_txd[*]}]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_txctl]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_rxc]
+set_property IOSTANDARD LVCMOS33 [get_ports {rgmii_rxd[*]}]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_rxctl]
+set_property IOSTANDARD LVCMOS33 [get_ports e_mdc]
+set_property IOSTANDARD LVCMOS33 [get_ports e_mdio]
+set_property IOSTANDARD LVCMOS33 [get_ports e_reset]
+
+set_property SLEW FAST [get_ports rgmii_txc]
+set_property SLEW FAST [get_ports rgmii_txctl]
+set_property SLEW FAST [get_ports {rgmii_txd[*]}]
+create_clock -period 8.000 [get_ports rgmii_rxc]
+
+# === DAC (J11 header) ===
+set_property IOSTANDARD LVCMOS33 [get_ports p2_clk]
+set_property IOSTANDARD LVCMOS33 [get_ports p2_wrt]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[13]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[12]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[11]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[10]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[9]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[8]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[7]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[6]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[5]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[4]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[3]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[2]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[1]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {p2_data[0]}]
+
+set_property SLEW FAST [get_ports p2_clk]
+
+set_property PACKAGE_PIN C18 [get_ports p2_clk]
+set_property PACKAGE_PIN C19 [get_ports p2_wrt]
+set_property PACKAGE_PIN B17 [get_ports {p2_data[13]}]
+set_property PACKAGE_PIN B18 [get_ports {p2_data[12]}]
+set_property PACKAGE_PIN D17 [get_ports {p2_data[11]}]
+set_property PACKAGE_PIN C17 [get_ports {p2_data[10]}]
+set_property PACKAGE_PIN A15 [get_ports {p2_data[9]}]
+set_property PACKAGE_PIN A16 [get_ports {p2_data[8]}]
+set_property PACKAGE_PIN B15 [get_ports {p2_data[7]}]
+set_property PACKAGE_PIN B16 [get_ports {p2_data[6]}]
+set_property PACKAGE_PIN A13 [get_ports {p2_data[5]}]
+set_property PACKAGE_PIN A14 [get_ports {p2_data[4]}]
+set_property PACKAGE_PIN E16 [get_ports {p2_data[3]}]
+set_property PACKAGE_PIN D16 [get_ports {p2_data[2]}]
+set_property PACKAGE_PIN C14 [get_ports {p2_data[1]}]
+set_property PACKAGE_PIN C15 [get_ports {p2_data[0]}]
+

designs/README.md

@@ -0,0 +1,5 @@
+# Директория с тестовыми проектами под ПЛИСу
+
+- eth_ctrl_debug: проект с ethernet и контроллером. Позволяет через ILA проверить, что пакет правильно принимается и что значения правильно выставляются.
+
+- eth_generator: проект на базе eth_ctrl_debug, в который включен генератор импульсов. В паре с ЦАП можно через консольку по Ethernet запускать генерацию разных импульсов.

designs/eth_ctrl_debug/Makefile

@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = eth_ctrl_debug_top
+FPGA_ARCH = artix7
+
+RTL_DIR = ../../rtl
+
+
+include ../../scripts/vivado.mk
+
+SYN_FILES += eth_ctrl_debug.sv
+SYN_FILES += $(sort $(shell find ../../rtl -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../../rtl/ethernet-udp/src -type f -name '*.xci'))
+XCI_FILES += $(sort $(shell find ip/ -type f -name '*.xci'))
+
+XDC_FILES += ../../constraints/ax7a035b.xdc
+XDC_FILES += debug.xdc
+
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

designs/eth_ctrl_debug/README.md

@@ -0,0 +1,7 @@
+# Тестовый проект Eth + CTRL
+Проект состоит из AXIS Ethernet и контроллера. Для тестирования сделано три разных частотных домена: ethernet 125MHz, DAC 130MHz, ADC 65MHz для тестирования сихронизации. Есть ILA на все выходы контроллера и на шину AXIS eth -> ctrl. Для отправки пакетов используйте скрипт ```console.py --debug```.
+
+## Сборка
+```make all``` - собрать все до битстрима
+
+```make vivado``` - открыть проект в Vivado

designs/eth_ctrl_debug/debug.xdc

@@ -0,0 +1,147 @@
+set_clock_groups -name ASYNC_UDP_CTRL -asynchronous -group [get_clocks rgmii_rxc] -group [get_clocks clk_out1_clk_wiz_ctrl_inst] -group [get_clocks clk_out2_clk_wiz_ctrl_inst]
+
+
+
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list clk_wiz_ctrl_inst/inst/clk_out2]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 32 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {adc_pulse_period_dbg[0]} {adc_pulse_period_dbg[1]} {adc_pulse_period_dbg[2]} {adc_pulse_period_dbg[3]} {adc_pulse_period_dbg[4]} {adc_pulse_period_dbg[5]} {adc_pulse_period_dbg[6]} {adc_pulse_period_dbg[7]} {adc_pulse_period_dbg[8]} {adc_pulse_period_dbg[9]} {adc_pulse_period_dbg[10]} {adc_pulse_period_dbg[11]} {adc_pulse_period_dbg[12]} {adc_pulse_period_dbg[13]} {adc_pulse_period_dbg[14]} {adc_pulse_period_dbg[15]} {adc_pulse_period_dbg[16]} {adc_pulse_period_dbg[17]} {adc_pulse_period_dbg[18]} {adc_pulse_period_dbg[19]} {adc_pulse_period_dbg[20]} {adc_pulse_period_dbg[21]} {adc_pulse_period_dbg[22]} {adc_pulse_period_dbg[23]} {adc_pulse_period_dbg[24]} {adc_pulse_period_dbg[25]} {adc_pulse_period_dbg[26]} {adc_pulse_period_dbg[27]} {adc_pulse_period_dbg[28]} {adc_pulse_period_dbg[29]} {adc_pulse_period_dbg[30]} {adc_pulse_period_dbg[31]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 8 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {finish_cnt[0]} {finish_cnt[1]} {finish_cnt[2]} {finish_cnt[3]} {finish_cnt[4]} {finish_cnt[5]} {finish_cnt[6]} {finish_cnt[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 16 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {adc_pulse_num_dbg[0]} {adc_pulse_num_dbg[1]} {adc_pulse_num_dbg[2]} {adc_pulse_num_dbg[3]} {adc_pulse_num_dbg[4]} {adc_pulse_num_dbg[5]} {adc_pulse_num_dbg[6]} {adc_pulse_num_dbg[7]} {adc_pulse_num_dbg[8]} {adc_pulse_num_dbg[9]} {adc_pulse_num_dbg[10]} {adc_pulse_num_dbg[11]} {adc_pulse_num_dbg[12]} {adc_pulse_num_dbg[13]} {adc_pulse_num_dbg[14]} {adc_pulse_num_dbg[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 1 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list adc_rst_dbg]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 1 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list adc_start_dbg]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 1 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list finish_dbg]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 1 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list finish_pending]]
+create_debug_core u_ila_1 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_1]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_1]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_1]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_1]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_1]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_1]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_1]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_1]
+set_property port_width 1 [get_debug_ports u_ila_1/clk]
+connect_debug_port u_ila_1/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe0]
+set_property port_width 2 [get_debug_ports u_ila_1/probe0]
+connect_debug_port u_ila_1/probe0 [get_nets [list {axis_mac0/rx_state[0]} {axis_mac0/rx_state[1]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe1]
+set_property port_width 16 [get_debug_ports u_ila_1/probe1]
+connect_debug_port u_ila_1/probe1 [get_nets [list {axis_mac0/udp_rec_data_length[0]} {axis_mac0/udp_rec_data_length[1]} {axis_mac0/udp_rec_data_length[2]} {axis_mac0/udp_rec_data_length[3]} {axis_mac0/udp_rec_data_length[4]} {axis_mac0/udp_rec_data_length[5]} {axis_mac0/udp_rec_data_length[6]} {axis_mac0/udp_rec_data_length[7]} {axis_mac0/udp_rec_data_length[8]} {axis_mac0/udp_rec_data_length[9]} {axis_mac0/udp_rec_data_length[10]} {axis_mac0/udp_rec_data_length[11]} {axis_mac0/udp_rec_data_length[12]} {axis_mac0/udp_rec_data_length[13]} {axis_mac0/udp_rec_data_length[14]} {axis_mac0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe2]
+set_property port_width 96 [get_debug_ports u_ila_1/probe2]
+connect_debug_port u_ila_1/probe2 [get_nets [list {udp_ctrl_inst/cfg_bus_eth[0]} {udp_ctrl_inst/cfg_bus_eth[1]} {udp_ctrl_inst/cfg_bus_eth[2]} {udp_ctrl_inst/cfg_bus_eth[3]} {udp_ctrl_inst/cfg_bus_eth[4]} {udp_ctrl_inst/cfg_bus_eth[5]} {udp_ctrl_inst/cfg_bus_eth[6]} {udp_ctrl_inst/cfg_bus_eth[7]} {udp_ctrl_inst/cfg_bus_eth[8]} {udp_ctrl_inst/cfg_bus_eth[9]} {udp_ctrl_inst/cfg_bus_eth[10]} {udp_ctrl_inst/cfg_bus_eth[11]} {udp_ctrl_inst/cfg_bus_eth[12]} {udp_ctrl_inst/cfg_bus_eth[13]} {udp_ctrl_inst/cfg_bus_eth[14]} {udp_ctrl_inst/cfg_bus_eth[15]} {udp_ctrl_inst/cfg_bus_eth[16]} {udp_ctrl_inst/cfg_bus_eth[17]} {udp_ctrl_inst/cfg_bus_eth[18]} {udp_ctrl_inst/cfg_bus_eth[19]} {udp_ctrl_inst/cfg_bus_eth[20]} {udp_ctrl_inst/cfg_bus_eth[21]} {udp_ctrl_inst/cfg_bus_eth[22]} {udp_ctrl_inst/cfg_bus_eth[23]} {udp_ctrl_inst/cfg_bus_eth[24]} {udp_ctrl_inst/cfg_bus_eth[25]} {udp_ctrl_inst/cfg_bus_eth[26]} {udp_ctrl_inst/cfg_bus_eth[27]} {udp_ctrl_inst/cfg_bus_eth[28]} {udp_ctrl_inst/cfg_bus_eth[29]} {udp_ctrl_inst/cfg_bus_eth[30]} {udp_ctrl_inst/cfg_bus_eth[31]} {udp_ctrl_inst/cfg_bus_eth[32]} {udp_ctrl_inst/cfg_bus_eth[33]} {udp_ctrl_inst/cfg_bus_eth[34]} {udp_ctrl_inst/cfg_bus_eth[35]} {udp_ctrl_inst/cfg_bus_eth[36]} {udp_ctrl_inst/cfg_bus_eth[37]} {udp_ctrl_inst/cfg_bus_eth[38]} {udp_ctrl_inst/cfg_bus_eth[39]} {udp_ctrl_inst/cfg_bus_eth[40]} {udp_ctrl_inst/cfg_bus_eth[41]} {udp_ctrl_inst/cfg_bus_eth[42]} {udp_ctrl_inst/cfg_bus_eth[43]} {udp_ctrl_inst/cfg_bus_eth[44]} {udp_ctrl_inst/cfg_bus_eth[45]} {udp_ctrl_inst/cfg_bus_eth[46]} {udp_ctrl_inst/cfg_bus_eth[47]} {udp_ctrl_inst/cfg_bus_eth[48]} {udp_ctrl_inst/cfg_bus_eth[49]} {udp_ctrl_inst/cfg_bus_eth[50]} {udp_ctrl_inst/cfg_bus_eth[51]} {udp_ctrl_inst/cfg_bus_eth[52]} {udp_ctrl_inst/cfg_bus_eth[53]} {udp_ctrl_inst/cfg_bus_eth[54]} {udp_ctrl_inst/cfg_bus_eth[55]} {udp_ctrl_inst/cfg_bus_eth[56]} {udp_ctrl_inst/cfg_bus_eth[57]} {udp_ctrl_inst/cfg_bus_eth[58]} {udp_ctrl_inst/cfg_bus_eth[59]} {udp_ctrl_inst/cfg_bus_eth[60]} {udp_ctrl_inst/cfg_bus_eth[61]} {udp_ctrl_inst/cfg_bus_eth[62]} {udp_ctrl_inst/cfg_bus_eth[63]} {udp_ctrl_inst/cfg_bus_eth[64]} {udp_ctrl_inst/cfg_bus_eth[65]} {udp_ctrl_inst/cfg_bus_eth[66]} {udp_ctrl_inst/cfg_bus_eth[67]} {udp_ctrl_inst/cfg_bus_eth[68]} {udp_ctrl_inst/cfg_bus_eth[69]} {udp_ctrl_inst/cfg_bus_eth[70]} {udp_ctrl_inst/cfg_bus_eth[71]} {udp_ctrl_inst/cfg_bus_eth[72]} {udp_ctrl_inst/cfg_bus_eth[73]} {udp_ctrl_inst/cfg_bus_eth[74]} {udp_ctrl_inst/cfg_bus_eth[75]} {udp_ctrl_inst/cfg_bus_eth[76]} {udp_ctrl_inst/cfg_bus_eth[77]} {udp_ctrl_inst/cfg_bus_eth[78]} {udp_ctrl_inst/cfg_bus_eth[79]} {udp_ctrl_inst/cfg_bus_eth[80]} {udp_ctrl_inst/cfg_bus_eth[81]} {udp_ctrl_inst/cfg_bus_eth[82]} {udp_ctrl_inst/cfg_bus_eth[83]} {udp_ctrl_inst/cfg_bus_eth[84]} {udp_ctrl_inst/cfg_bus_eth[85]} {udp_ctrl_inst/cfg_bus_eth[86]} {udp_ctrl_inst/cfg_bus_eth[87]} {udp_ctrl_inst/cfg_bus_eth[88]} {udp_ctrl_inst/cfg_bus_eth[89]} {udp_ctrl_inst/cfg_bus_eth[90]} {udp_ctrl_inst/cfg_bus_eth[91]} {udp_ctrl_inst/cfg_bus_eth[92]} {udp_ctrl_inst/cfg_bus_eth[93]} {udp_ctrl_inst/cfg_bus_eth[94]} {udp_ctrl_inst/cfg_bus_eth[95]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe3]
+set_property port_width 16 [get_debug_ports u_ila_1/probe3]
+connect_debug_port u_ila_1/probe3 [get_nets [list {axis_mac0/rx_payload_len[0]} {axis_mac0/rx_payload_len[1]} {axis_mac0/rx_payload_len[2]} {axis_mac0/rx_payload_len[3]} {axis_mac0/rx_payload_len[4]} {axis_mac0/rx_payload_len[5]} {axis_mac0/rx_payload_len[6]} {axis_mac0/rx_payload_len[7]} {axis_mac0/rx_payload_len[8]} {axis_mac0/rx_payload_len[9]} {axis_mac0/rx_payload_len[10]} {axis_mac0/rx_payload_len[11]} {axis_mac0/rx_payload_len[12]} {axis_mac0/rx_payload_len[13]} {axis_mac0/rx_payload_len[14]} {axis_mac0/rx_payload_len[15]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe4]
+set_property port_width 8 [get_debug_ports u_ila_1/probe4]
+connect_debug_port u_ila_1/probe4 [get_nets [list {m_axis_rx_tdata[0]} {m_axis_rx_tdata[1]} {m_axis_rx_tdata[2]} {m_axis_rx_tdata[3]} {m_axis_rx_tdata[4]} {m_axis_rx_tdata[5]} {m_axis_rx_tdata[6]} {m_axis_rx_tdata[7]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe5]
+set_property port_width 3 [get_debug_ports u_ila_1/probe5]
+connect_debug_port u_ila_1/probe5 [get_nets [list {udp_ctrl_inst/eth_state[0]} {udp_ctrl_inst/eth_state[1]} {udp_ctrl_inst/eth_state[2]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe6]
+set_property port_width 1 [get_debug_ports u_ila_1/probe6]
+connect_debug_port u_ila_1/probe6 [get_nets [list axis_mac0/arp_found]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe7]
+set_property port_width 1 [get_debug_ports u_ila_1/probe7]
+connect_debug_port u_ila_1/probe7 [get_nets [list udp_ctrl_inst/axis_hs]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe8]
+set_property port_width 1 [get_debug_ports u_ila_1/probe8]
+connect_debug_port u_ila_1/probe8 [get_nets [list udp_ctrl_inst/busy_flag_eth]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe9]
+set_property port_width 1 [get_debug_ports u_ila_1/probe9]
+connect_debug_port u_ila_1/probe9 [get_nets [list axis_mac0/m_axis_rx_tlast]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe10]
+set_property port_width 1 [get_debug_ports u_ila_1/probe10]
+connect_debug_port u_ila_1/probe10 [get_nets [list m_axis_rx_tlast]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe11]
+set_property port_width 1 [get_debug_ports u_ila_1/probe11]
+connect_debug_port u_ila_1/probe11 [get_nets [list axis_mac0/m_axis_rx_tready]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe12]
+set_property port_width 1 [get_debug_ports u_ila_1/probe12]
+connect_debug_port u_ila_1/probe12 [get_nets [list m_axis_rx_tready]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe13]
+set_property port_width 1 [get_debug_ports u_ila_1/probe13]
+connect_debug_port u_ila_1/probe13 [get_nets [list axis_mac0/req_ready]]
+create_debug_core u_ila_2 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_2]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_2]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_2]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_2]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_2]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_2]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_2]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_2]
+set_property port_width 1 [get_debug_ports u_ila_2/clk]
+connect_debug_port u_ila_2/clk [get_nets [list clk_wiz_ctrl_inst/inst/clk_out1]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe0]
+set_property port_width 12 [get_debug_ports u_ila_2/probe0]
+connect_debug_port u_ila_2/probe0 [get_nets [list {dac_pulse_height_dbg[0]} {dac_pulse_height_dbg[1]} {dac_pulse_height_dbg[2]} {dac_pulse_height_dbg[3]} {dac_pulse_height_dbg[4]} {dac_pulse_height_dbg[5]} {dac_pulse_height_dbg[6]} {dac_pulse_height_dbg[7]} {dac_pulse_height_dbg[8]} {dac_pulse_height_dbg[9]} {dac_pulse_height_dbg[10]} {dac_pulse_height_dbg[11]}]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe1]
+set_property port_width 16 [get_debug_ports u_ila_2/probe1]
+connect_debug_port u_ila_2/probe1 [get_nets [list {dac_pulse_num_dbg[0]} {dac_pulse_num_dbg[1]} {dac_pulse_num_dbg[2]} {dac_pulse_num_dbg[3]} {dac_pulse_num_dbg[4]} {dac_pulse_num_dbg[5]} {dac_pulse_num_dbg[6]} {dac_pulse_num_dbg[7]} {dac_pulse_num_dbg[8]} {dac_pulse_num_dbg[9]} {dac_pulse_num_dbg[10]} {dac_pulse_num_dbg[11]} {dac_pulse_num_dbg[12]} {dac_pulse_num_dbg[13]} {dac_pulse_num_dbg[14]} {dac_pulse_num_dbg[15]}]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe2]
+set_property port_width 32 [get_debug_ports u_ila_2/probe2]
+connect_debug_port u_ila_2/probe2 [get_nets [list {dac_pulse_period_dbg[0]} {dac_pulse_period_dbg[1]} {dac_pulse_period_dbg[2]} {dac_pulse_period_dbg[3]} {dac_pulse_period_dbg[4]} {dac_pulse_period_dbg[5]} {dac_pulse_period_dbg[6]} {dac_pulse_period_dbg[7]} {dac_pulse_period_dbg[8]} {dac_pulse_period_dbg[9]} {dac_pulse_period_dbg[10]} {dac_pulse_period_dbg[11]} {dac_pulse_period_dbg[12]} {dac_pulse_period_dbg[13]} {dac_pulse_period_dbg[14]} {dac_pulse_period_dbg[15]} {dac_pulse_period_dbg[16]} {dac_pulse_period_dbg[17]} {dac_pulse_period_dbg[18]} {dac_pulse_period_dbg[19]} {dac_pulse_period_dbg[20]} {dac_pulse_period_dbg[21]} {dac_pulse_period_dbg[22]} {dac_pulse_period_dbg[23]} {dac_pulse_period_dbg[24]} {dac_pulse_period_dbg[25]} {dac_pulse_period_dbg[26]} {dac_pulse_period_dbg[27]} {dac_pulse_period_dbg[28]} {dac_pulse_period_dbg[29]} {dac_pulse_period_dbg[30]} {dac_pulse_period_dbg[31]}]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe3]
+set_property port_width 32 [get_debug_ports u_ila_2/probe3]
+connect_debug_port u_ila_2/probe3 [get_nets [list {dac_pulse_width_dbg[0]} {dac_pulse_width_dbg[1]} {dac_pulse_width_dbg[2]} {dac_pulse_width_dbg[3]} {dac_pulse_width_dbg[4]} {dac_pulse_width_dbg[5]} {dac_pulse_width_dbg[6]} {dac_pulse_width_dbg[7]} {dac_pulse_width_dbg[8]} {dac_pulse_width_dbg[9]} {dac_pulse_width_dbg[10]} {dac_pulse_width_dbg[11]} {dac_pulse_width_dbg[12]} {dac_pulse_width_dbg[13]} {dac_pulse_width_dbg[14]} {dac_pulse_width_dbg[15]} {dac_pulse_width_dbg[16]} {dac_pulse_width_dbg[17]} {dac_pulse_width_dbg[18]} {dac_pulse_width_dbg[19]} {dac_pulse_width_dbg[20]} {dac_pulse_width_dbg[21]} {dac_pulse_width_dbg[22]} {dac_pulse_width_dbg[23]} {dac_pulse_width_dbg[24]} {dac_pulse_width_dbg[25]} {dac_pulse_width_dbg[26]} {dac_pulse_width_dbg[27]} {dac_pulse_width_dbg[28]} {dac_pulse_width_dbg[29]} {dac_pulse_width_dbg[30]} {dac_pulse_width_dbg[31]}]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe4]
+set_property port_width 1 [get_debug_ports u_ila_2/probe4]
+connect_debug_port u_ila_2/probe4 [get_nets [list dac_rst_dbg]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe5]
+set_property port_width 1 [get_debug_ports u_ila_2/probe5]
+connect_debug_port u_ila_2/probe5 [get_nets [list dac_start_dbg]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets dac_clk]

designs/eth_ctrl_debug/eth_ctrl_debug.sv

@@ -0,0 +1,298 @@
+`timescale 1 ns / 1 ns
+
+module eth_ctrl_debug_top #(
+    parameter int unsigned DAC_DATA_WIDTH = 12
+)(
+    input               sys_clk_p,
+    input               sys_clk_n,
+    input               rst_n,
+
+    output [3:0]        led,
+
+    output              e_reset,
+    output              e_mdc,
+    inout               e_mdio,
+
+    output [3:0]        rgmii_txd,
+    output              rgmii_txctl,
+    output              rgmii_txc,
+    input  [3:0]        rgmii_rxd,
+    input               rgmii_rxctl,
+    input               rgmii_rxc
+);
+
+    // -------------------------------------------------------------------------
+    // Internal GMII-side signals
+    // -------------------------------------------------------------------------
+    wire  [7:0] gmii_txd;
+    wire        gmii_tx_en;
+    wire        gmii_tx_er;
+    wire        gmii_tx_clk;
+    wire        gmii_crs;
+    wire        gmii_col;
+    wire  [7:0] gmii_rxd_i;
+    wire        gmii_rx_dv;
+    wire        gmii_rx_er;
+    wire        gmii_rx_clk;
+
+    wire [31:0] pack_total_len;
+
+    wire        e_rx_dv;
+    wire [7:0]  e_rxd;
+    wire        e_tx_en;
+    wire [7:0]  e_txd;
+    wire        e_rst_n;
+    wire        sys_clk;
+
+    wire        duplex_mode;
+
+    assign duplex_mode = 1'b1;
+
+    // -------------------------------------------------------------------------
+    // System clock buffer (200 MHz differential input)
+    // -------------------------------------------------------------------------
+    IBUFDS sys_clk_ibufgds (
+        .O  (sys_clk),
+        .I  (sys_clk_p),
+        .IB (sys_clk_n)
+    );
+
+    // -------------------------------------------------------------------------
+    // IDELAYCTRL
+    // -------------------------------------------------------------------------
+    (* IODELAY_GROUP = "rgmii_idelay_group" *)
+    IDELAYCTRL IDELAYCTRL_inst (
+        .RDY    (),
+        .REFCLK (sys_clk),
+        .RST    (1'b0)
+    );
+
+    // -------------------------------------------------------------------------
+    // Generated clocks for controller
+    // Need to create this IP in Vivado:
+    //  input : 200 MHz
+    //  output0: 130 MHz
+    //  output1: 65 MHz
+    // -------------------------------------------------------------------------
+    wire dac_clk;
+    wire adc_clk;
+    wire clk_wiz_locked;
+
+    clk_wiz_ctrl_inst clk_wiz_ctrl_inst (
+        .clk_in1   (sys_clk),
+        .reset    (~rst_n),
+        .clk_out1  (dac_clk),   // 130 MHz
+        .clk_out2  (adc_clk),   // 65 MHz
+        .locked    (clk_wiz_locked)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII <-> RGMII conversion
+    // -------------------------------------------------------------------------
+    util_gmii_to_rgmii util_gmii_to_rgmii_m0 (
+        .reset           (1'b0),
+        .rgmii_td        (rgmii_txd),
+        .rgmii_tx_ctl    (rgmii_txctl),
+        .rgmii_txc       (rgmii_txc),
+        .rgmii_rd        (rgmii_rxd),
+        .rgmii_rx_ctl    (rgmii_rxctl),
+        .gmii_rx_clk     (gmii_rx_clk),
+        .gmii_txd        (e_txd),
+        .gmii_tx_en      (e_tx_en),
+        .gmii_tx_er      (1'b0),
+        .gmii_tx_clk     (gmii_tx_clk),
+        .gmii_crs        (gmii_crs),
+        .gmii_col        (gmii_col),
+        .gmii_rxd        (gmii_rxd_i),
+        .rgmii_rxc       (rgmii_rxc),
+        .gmii_rx_dv      (gmii_rx_dv),
+        .gmii_rx_er      (gmii_rx_er),
+        .speed_selection (2'b10),
+        .duplex_mode     (duplex_mode)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII arbitration / adaptation
+    // -------------------------------------------------------------------------
+    gmii_arbi arbi_inst (
+        .clk            (gmii_tx_clk),
+        .rst_n          (rst_n),
+        .speed          (2'b10),
+        .link           (1'b1),
+        .pack_total_len (pack_total_len),
+        .e_rst_n        (e_rst_n),
+        .gmii_rx_dv     (gmii_rx_dv),
+        .gmii_rxd       (gmii_rxd_i),
+        .gmii_tx_en     (gmii_tx_en),
+        .gmii_txd       (gmii_txd),
+        .e_rx_dv        (e_rx_dv),
+        .e_rxd          (e_rxd),
+        .e_tx_en        (e_tx_en),
+        .e_txd          (e_txd)
+    );
+
+    // -------------------------------------------------------------------------
+    // axis_mac interface
+    // RX stream from Ethernet goes into controller
+    // TX stream is unused for now
+    // -------------------------------------------------------------------------
+    wire        req_ready;
+
+    reg         send_req;
+    reg  [15:0] data_length;
+
+    reg  [7:0]  s_axis_tx_tdata;
+    reg         s_axis_tx_tvalid;
+    wire        s_axis_tx_tready;
+    reg         s_axis_tx_tlast;
+
+    (* MARK_DEBUG="true" *) wire [7:0]  m_axis_rx_tdata;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tvalid;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tlast;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tready;
+
+    // Always ready to accept RX payload bytes
+    assign m_axis_rx_tready = 1'b1;
+
+    // TX disabled
+    always @(*) begin
+        send_req        = 1'b0;
+        data_length     = 16'd0;
+        s_axis_tx_tdata = 8'd0;
+        s_axis_tx_tvalid= 1'b0;
+        s_axis_tx_tlast = 1'b0;
+    end
+
+    axis_mac axis_mac0 (
+        .gmii_tx_clk       (gmii_tx_clk),
+        .gmii_rx_clk       (gmii_rx_clk),
+        .rst_n             (e_rst_n),
+
+        .gmii_rx_dv        (e_rx_dv),
+        .gmii_rxd          (e_rxd),
+        .gmii_tx_en        (gmii_tx_en),
+        .gmii_txd          (gmii_txd),
+
+        .send_req          (send_req),
+        .data_length       (data_length),
+        .req_ready         (req_ready),
+
+        .s_axis_tx_tdata   (s_axis_tx_tdata),
+        .s_axis_tx_tvalid  (s_axis_tx_tvalid),
+        .s_axis_tx_tready  (s_axis_tx_tready),
+        .s_axis_tx_tlast   (s_axis_tx_tlast),
+
+        .m_axis_rx_tdata   (m_axis_rx_tdata),
+        .m_axis_rx_tvalid  (m_axis_rx_tvalid),
+        .m_axis_rx_tready  (m_axis_rx_tready),
+        .m_axis_rx_tlast   (m_axis_rx_tlast)
+    );
+
+    // PHY reset helper from your original example
+    reset reset_m0 (
+        .clk   (sys_clk),
+        .key1  (rst_n),
+        .rst_n (e_reset)
+    );
+
+    // MDIO lines are not driven here yet
+    assign e_mdc  = 1'b0;
+    assign e_mdio = 1'bz;
+
+    // -------------------------------------------------------------------------
+    // Controller reset
+    // Use both external reset and clk_wiz lock
+    // -------------------------------------------------------------------------
+    wire ctrl_rst_n = rst_n & clk_wiz_locked;
+
+    // -------------------------------------------------------------------------
+    // Debug finish generator
+    //
+    // After each adc_start pulse generates one finish pulse after some delay.
+    // This is just for first bring-up so the controller can leave busy state
+    // If you don't want this, replace with:
+    // wire finish_dbg = 1'b0;
+    // -------------------------------------------------------------------------
+    (* MARK_DEBUG="true" *) logic        finish_dbg;
+    (* MARK_DEBUG="true" *) logic [7:0]  finish_cnt;
+    (* MARK_DEBUG="true" *) logic        finish_pending;
+
+    // Controller outputs to debug
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_width_dbg;
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_period_dbg;
+    (* MARK_DEBUG="true" *) wire [DAC_DATA_WIDTH-1:0] dac_pulse_height_dbg;
+    (* MARK_DEBUG="true" *) wire [15:0]               dac_pulse_num_dbg;
+
+    (* MARK_DEBUG="true" *) wire [31:0]               adc_pulse_period_dbg;
+    (* MARK_DEBUG="true" *) wire [15:0]               adc_pulse_num_dbg;
+
+    (* MARK_DEBUG="true" *) wire                      dac_start_dbg;
+    (* MARK_DEBUG="true" *) wire                      adc_start_dbg;
+    (* MARK_DEBUG="true" *) wire                      dac_rst_dbg;
+    (* MARK_DEBUG="true" *) wire                      adc_rst_dbg;
+
+    always_ff @(posedge adc_clk or negedge ctrl_rst_n) begin
+        if (!ctrl_rst_n) begin
+            finish_dbg     <= 1'b0;
+            finish_cnt     <= 8'd0;
+            finish_pending <= 1'b0;
+        end else begin
+            finish_dbg <= 1'b0;
+
+            if (adc_start_dbg) begin
+                finish_pending <= 1'b1;
+                finish_cnt     <= 8'd80;
+            end else if (finish_pending) begin
+                if (finish_cnt == 8'd0) begin
+                    finish_dbg     <= 1'b1;
+                    finish_pending <= 1'b0;
+                end else begin
+                    finish_cnt <= finish_cnt - 8'd1;
+                end
+            end
+        end
+    end
+
+    // -------------------------------------------------------------------------
+    // Controller
+    // ETH domain = gmii_rx_clk, because RX AXI master comes from axis_mac RX side
+    // -------------------------------------------------------------------------
+    control #(
+        .DAC_DATA_WIDTH(DAC_DATA_WIDTH)
+    ) udp_ctrl_inst (
+        .eth_clk_in        (gmii_rx_clk),
+        .dac_clk_in        (dac_clk),
+        .adc_clk_in        (adc_clk),
+        .rst_n             (ctrl_rst_n),
+
+        .s_axis_tdata      (m_axis_rx_tdata),
+        .s_axis_tvalid     (m_axis_rx_tvalid),
+        .s_axis_tready     (), // controller internally always ready in current version
+        .s_axis_tlast      (m_axis_rx_tlast),
+
+        .finish            (finish_dbg),
+
+        .dac_pulse_width   (dac_pulse_width_dbg),
+        .dac_pulse_period  (dac_pulse_period_dbg),
+        .dac_pulse_height  (dac_pulse_height_dbg),
+        .dac_pulse_num     (dac_pulse_num_dbg),
+
+        .adc_pulse_period  (adc_pulse_period_dbg),
+        .adc_pulse_num     (adc_pulse_num_dbg),
+
+        .dac_start         (dac_start_dbg),
+        .adc_start         (adc_start_dbg),
+
+        .dac_rst           (dac_rst_dbg),
+        .adc_rst           (adc_rst_dbg)
+    );
+
+    // -------------------------------------------------------------------------
+    // Simple LED status
+    // -------------------------------------------------------------------------
+    assign led[0] = clk_wiz_locked;
+    assign led[1] = m_axis_rx_tvalid;
+    assign led[2] = dac_start_dbg;
+    assign led[3] = adc_rst_dbg;
+
+endmodule

designs/eth_ctrl_debug/ip/clk_wiz_ctrl_inst.xci

@@ -0,0 +1,689 @@
+{
+  "schema": "xilinx.com:schema:json_instance:1.0",
+  "ip_inst": {
+    "xci_name": "clk_wiz_ctrl_inst",
+    "component_reference": "xilinx.com:ip:clk_wiz:6.0",
+    "ip_revision": "16",
+    "gen_directory": "../../../../eth_ctrl_debug_top.gen/sources_1/ip/clk_wiz_ctrl_inst",
+    "parameters": {
+      "component_parameters": {
+        "Component_Name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "user", "usage": "all" } ],
+        "USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "ENABLE_CLOCK_MONITOR": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK2": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK3": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRECISION": [ { "value": "1", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "PRIMTYPE_SEL": [ { "value": "mmcm_adv", "resolve_type": "user", "usage": "all" } ],
+        "CLOCK_MGR_TYPE": [ { "value": "auto", "resolve_type": "user", "usage": "all" } ],
+        "USE_FREQ_SYNTH": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_SPREAD_SPECTRUM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_PHASE_ALIGNMENT": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_POWER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_PHASE_SHIFT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_RECONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "user", "usage": "all" } ],
+        "PRIM_IN_FREQ": [ { "value": "200.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "user", "usage": "all" } ],
+        "PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "user", "usage": "all" } ],
+        "IN_JITTER_UNITS": [ { "value": "Units_UI", "resolve_type": "user", "usage": "all" } ],
+        "RELATIVE_INCLK": [ { "value": "REL_PRIMARY", "resolve_type": "user", "usage": "all" } ],
+        "USE_INCLK_SWITCHOVER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "user", "usage": "all" } ],
+        "SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "JITTER_OPTIONS": [ { "value": "UI", "resolve_type": "user", "usage": "all" } ],
+        "CLKIN1_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN1_JITTER_PS": [ { "value": "50.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_USED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_USED": [ { "value": "true", "value_src": "user", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "NUM_OUT_CLKS": [ { "value": "2", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLK_OUT1_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT2_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT3_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT4_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT5_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT6_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT7_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "user", "usage": "all" } ],
+        "DADDR_PORT": [ { "value": "daddr", "resolve_type": "user", "usage": "all" } ],
+        "DCLK_PORT": [ { "value": "dclk", "resolve_type": "user", "usage": "all" } ],
+        "DRDY_PORT": [ { "value": "drdy", "resolve_type": "user", "usage": "all" } ],
+        "DWE_PORT": [ { "value": "dwe", "resolve_type": "user", "usage": "all" } ],
+        "DIN_PORT": [ { "value": "din", "resolve_type": "user", "usage": "all" } ],
+        "DOUT_PORT": [ { "value": "dout", "resolve_type": "user", "usage": "all" } ],
+        "DEN_PORT": [ { "value": "den", "resolve_type": "user", "usage": "all" } ],
+        "PSCLK_PORT": [ { "value": "psclk", "resolve_type": "user", "usage": "all" } ],
+        "PSEN_PORT": [ { "value": "psen", "resolve_type": "user", "usage": "all" } ],
+        "PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "user", "usage": "all" } ],
+        "PSDONE_PORT": [ { "value": "psdone", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "130.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USE_MAX_I_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_O_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "user", "usage": "all" } ],
+        "PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "user", "usage": "all" } ],
+        "SUMMARY_STRINGS": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_LOCKED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CALC_DONE": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_RESET": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_POWER_DOWN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_STATUS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_FREEZE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLK_VALID": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_INCLK_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLKFB_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "RESET_PORT": [ { "value": "reset", "resolve_type": "user", "usage": "all" } ],
+        "LOCKED_PORT": [ { "value": "locked", "resolve_type": "user", "usage": "all" } ],
+        "POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "user", "usage": "all" } ],
+        "CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "user", "usage": "all" } ],
+        "STATUS_PORT": [ { "value": "STATUS", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "user", "usage": "all" } ],
+        "INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "user", "usage": "all" } ],
+        "SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "SS_MOD_FREQ": [ { "value": "250", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "OVERRIDE_MMCM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_DIVCLK_DIVIDE": [ { "value": "1", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_CLKFBOUT_MULT_F": [ { "value": "4.875", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_CASCADE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLOCK_HOLD": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_STARTUP_WAIT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT0_DIVIDE_F": [ { "value": "7.500", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT1_DIVIDE": [ { "value": "15", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OVERRIDE_PLL": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PLL_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "PLL_CLKFBOUT_MULT": [ { "value": "4", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "user", "usage": "all" } ],
+        "PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKIN_PERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "user", "usage": "all" } ],
+        "PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "RESET_TYPE": [ { "value": "ACTIVE_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "USE_SAFE_CLOCK_STARTUP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLOCK_SEQUENCING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "USE_BOARD_FLOW": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "RESET_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CDDC": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "user", "usage": "all" } ],
+        "CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CLKOUTPHY": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUTPHY_REQUESTED_FREQ": [ { "value": "600.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_JITTER": [ { "value": "102.676", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_PHASE_ERROR": [ { "value": "87.159", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_JITTER": [ { "value": "117.878", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_PHASE_ERROR": [ { "value": "87.159", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "INPUT_MODE": [ { "value": "frequency", "resolve_type": "user", "usage": "all" } ],
+        "INTERFACE_SELECTION": [ { "value": "Enable_AXI", "resolve_type": "user", "usage": "all" } ],
+        "AXI_DRP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PHASE_DUTY_CONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ]
+      },
+      "model_parameters": {
+        "C_CLKOUT2_USED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_ENABLE_CLOCK_MONITOR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK2": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK3": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRECISION": [ { "value": "1", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT1_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT2_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT3_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT4_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "c_component_name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_FREQ_SYNTH": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_PHASE_ALIGNMENT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_MIN_POWER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MIN_O_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MAX_I_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_PHASE_SHIFT": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_SWITCHOVER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_RECONFIG": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_SPREAD_SPECTRUM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FAST_SIMULATION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMTYPE_SEL": [ { "value": "AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_CLK_VALID": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_FREQ": [ { "value": "200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_RESET": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_RESET_LOW": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_LOCKED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKFB_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_POWER_DOWN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_STATUS": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FREEZE": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_NUM_OUT_CLKS": [ { "value": "2", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW0": [ { "value": "Input Clock   Freq (MHz)    Input Jitter (UI)", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW1": [ { "value": "__primary_________200.000____________0.010", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW2": [ { "value": "no_secondary_input_clock ", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0A": [ { "value": " Output     Output      Phase    Duty Cycle   Pk-to-Pk     Phase", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0B": [ { "value": "  Clock     Freq (MHz)  (degrees)    (%)     Jitter (ps)  Error (ps)", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW1": [ { "value": "clk_out1__130.00000______0.000______50.0______102.676_____87.159", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW2": [ { "value": "clk_out2__65.00000______0.000______50.0______117.878_____87.159", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW3": [ { "value": "no_CLK_OUT3_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW4": [ { "value": "no_CLK_OUT4_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW5": [ { "value": "no_CLK_OUT5_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW6": [ { "value": "no_CLK_OUT6_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW7": [ { "value": "no_CLK_OUT7_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "130.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_OUT_FREQ": [ { "value": "130.00000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_OUT_FREQ": [ { "value": "65.00000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USE_SAFE_CLOCK_STARTUP": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLOCK_SEQUENCING": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_NOTES": [ { "value": "None", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_MULT_F": [ { "value": "4.875", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_CASCADE": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_CLOCK_HOLD": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_STARTUP_WAIT": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DIVIDE_F": [ { "value": "7.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DIVIDE": [ { "value": "15", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_NOTES": [ { "value": "No notes", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_MULT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKIN_PERIOD": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLOCK_MGR_TYPE": [ { "value": "NA", "resolve_type": "generated", "usage": "all" } ],
+        "C_OVERRIDE_MMCM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OVERRIDE_PLL": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "generated", "usage": "all" } ],
+        "C_RESET_PORT": [ { "value": "reset", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCKED_PORT": [ { "value": "locked", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "generated", "usage": "all" } ],
+        "C_DADDR_PORT": [ { "value": "daddr", "resolve_type": "generated", "usage": "all" } ],
+        "C_DCLK_PORT": [ { "value": "dclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_DRDY_PORT": [ { "value": "drdy", "resolve_type": "generated", "usage": "all" } ],
+        "C_DWE_PORT": [ { "value": "dwe", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIN_PORT": [ { "value": "din", "resolve_type": "generated", "usage": "all" } ],
+        "C_DOUT_PORT": [ { "value": "dout", "resolve_type": "generated", "usage": "all" } ],
+        "C_DEN_PORT": [ { "value": "den", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSCLK_PORT": [ { "value": "psclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSEN_PORT": [ { "value": "psen", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSDONE_PORT": [ { "value": "psdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "generated", "usage": "all" } ],
+        "C_STATUS_PORT": [ { "value": "STATUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "generated", "usage": "all" } ],
+        "C_INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKIN1_JITTER_PS": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MOD_PERIOD": [ { "value": "4000", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_HAS_CDDC": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUTPHY_MODE": [ { "value": "VCO", "resolve_type": "generated", "usage": "all" } ],
+        "C_ENABLE_CLKOUTPHY": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_INTERFACE_SELECTION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_ADDR_WIDTH": [ { "value": "11", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_DATA_WIDTH": [ { "value": "32", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_POWER_REG": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVCLK": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_3": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE1_AUTO": [ { "value": "1", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE2_AUTO": [ { "value": "2.0", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE3_AUTO": [ { "value": "0.13333333333333333", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE4_AUTO": [ { "value": "0.13333333333333333", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE5_AUTO": [ { "value": "0.13333333333333333", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE6_AUTO": [ { "value": "0.13333333333333333", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE7_AUTO": [ { "value": "0.13333333333333333", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV5": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV6": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV7": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_ACTUAL_FREQ": [ { "value": "130.00000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_ACTUAL_FREQ": [ { "value": "65.00000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_M_MAX": [ { "value": "64.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_M_MIN": [ { "value": "2.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MAX": [ { "value": "80.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MAX": [ { "value": "128.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MIN": [ { "value": "600.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MAX": [ { "value": "1200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ]
+      },
+      "project_parameters": {
+        "ARCHITECTURE": [ { "value": "artix7" } ],
+        "BASE_BOARD_PART": [ { "value": "" } ],
+        "BOARD_CONNECTIONS": [ { "value": "" } ],
+        "DEVICE": [ { "value": "xc7a35t" } ],
+        "PACKAGE": [ { "value": "fgg484" } ],
+        "PREFHDL": [ { "value": "VERILOG" } ],
+        "SILICON_REVISION": [ { "value": "" } ],
+        "SIMULATOR_LANGUAGE": [ { "value": "MIXED" } ],
+        "SPEEDGRADE": [ { "value": "-1" } ],
+        "STATIC_POWER": [ { "value": "" } ],
+        "TEMPERATURE_GRADE": [ { "value": "" } ]
+      },
+      "runtime_parameters": {
+        "IPCONTEXT": [ { "value": "IP_Flow" } ],
+        "IPREVISION": [ { "value": "16" } ],
+        "MANAGED": [ { "value": "TRUE" } ],
+        "OUTPUTDIR": [ { "value": "../../../../eth_ctrl_debug_top.gen/sources_1/ip/clk_wiz_ctrl_inst" } ],
+        "SELECTEDSIMMODEL": [ { "value": "" } ],
+        "SHAREDDIR": [ { "value": "." } ],
+        "SWVERSION": [ { "value": "2025.1" } ],
+        "SYNTHESISFLOW": [ { "value": "OUT_OF_CONTEXT" } ]
+      }
+    },
+    "boundary": {
+      "ports": {
+        "reset": [ { "direction": "in", "driver_value": "0" } ],
+        "clk_in1": [ { "direction": "in" } ],
+        "clk_out1": [ { "direction": "out" } ],
+        "clk_out2": [ { "direction": "out" } ],
+        "locked": [ { "direction": "out" } ]
+      },
+      "interfaces": {
+        "reset": {
+          "vlnv": "xilinx.com:signal:reset:1.0",
+          "abstraction_type": "xilinx.com:signal:reset_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "POLARITY": [ { "value": "ACTIVE_HIGH", "value_src": "constant", "usage": "all" } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "RESET_BOARD_INTERFACE", "value_src": "constant", "usage": "all" } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "RST": [ { "physical_name": "reset" } ]
+          }
+        },
+        "clock_CLK_IN1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "CLK_IN1_BOARD_INTERFACE", "usage": "all", "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_IN1": [ { "physical_name": "clk_in1" } ]
+          }
+        },
+        "clock_CLK_OUT1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT1": [ { "physical_name": "clk_out1" } ]
+          }
+        },
+        "clock_CLK_OUT2": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT2": [ { "physical_name": "clk_out2" } ]
+          }
+        }
+      }
+    }
+  }
+}

designs/eth_generator/Makefile

@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = eth_generator_top
+FPGA_ARCH = artix7
+
+RTL_DIR = ../../rtl
+
+
+include ../../scripts/vivado.mk
+
+SYN_FILES += eth_generator.sv
+SYN_FILES += $(sort $(shell find ../../rtl -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../../rtl/ethernet-udp/src -type f -name '*.xci'))
+XCI_FILES += $(sort $(shell find ip/ -type f -name '*.xci'))
+
+XDC_FILES += ../../constraints/ax7a035b.xdc
+XDC_FILES += debug.xdc
+
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

designs/eth_generator/README.md

@@ -0,0 +1,11 @@
+# Тестовый проект Generator + ETH + CTRL
+Проект состоит из AXIS Ethernet, контроллера и генератора. Позволяет генерировать сигналы, задав параметры через Ethernet.
+## Сборка
+```make all``` - собрать все до битстрима
+
+```make vivado``` - открыть проект в Vivado
+
+## Управление
+Используйте software/console.py. Пример:
+
+```python3 console.py --pulse_width 3_500_000 --pulse_period 20_000_000 --pulse_height 10000 --pulse_num 5500 --dac-bits 14```

designs/eth_generator/debug.xdc

@@ -0,0 +1,117 @@
+set_clock_groups -name ASYNC_UDP_CTRL -asynchronous -group [get_clocks rgmii_rxc] -group [get_clocks clk_out1_clk_wiz_ctrl_inst] -group [get_clocks clk_out2_clk_wiz_ctrl_inst]
+
+
+
+
+connect_debug_port u_ila_2/probe0 [get_nets [list {dac_pulse_height_dbg[0]} {dac_pulse_height_dbg[1]} {dac_pulse_height_dbg[2]} {dac_pulse_height_dbg[3]} {dac_pulse_height_dbg[4]} {dac_pulse_height_dbg[5]} {dac_pulse_height_dbg[6]} {dac_pulse_height_dbg[7]} {dac_pulse_height_dbg[8]} {dac_pulse_height_dbg[9]} {dac_pulse_height_dbg[10]} {dac_pulse_height_dbg[11]}]]
+connect_debug_port u_ila_2/probe1 [get_nets [list {dac_pulse_num_dbg[0]} {dac_pulse_num_dbg[1]} {dac_pulse_num_dbg[2]} {dac_pulse_num_dbg[3]} {dac_pulse_num_dbg[4]} {dac_pulse_num_dbg[5]} {dac_pulse_num_dbg[6]} {dac_pulse_num_dbg[7]} {dac_pulse_num_dbg[8]} {dac_pulse_num_dbg[9]} {dac_pulse_num_dbg[10]} {dac_pulse_num_dbg[11]} {dac_pulse_num_dbg[12]} {dac_pulse_num_dbg[13]} {dac_pulse_num_dbg[14]} {dac_pulse_num_dbg[15]}]]
+connect_debug_port u_ila_2/probe2 [get_nets [list {dac_pulse_period_dbg[0]} {dac_pulse_period_dbg[1]} {dac_pulse_period_dbg[2]} {dac_pulse_period_dbg[3]} {dac_pulse_period_dbg[4]} {dac_pulse_period_dbg[5]} {dac_pulse_period_dbg[6]} {dac_pulse_period_dbg[7]} {dac_pulse_period_dbg[8]} {dac_pulse_period_dbg[9]} {dac_pulse_period_dbg[10]} {dac_pulse_period_dbg[11]} {dac_pulse_period_dbg[12]} {dac_pulse_period_dbg[13]} {dac_pulse_period_dbg[14]} {dac_pulse_period_dbg[15]} {dac_pulse_period_dbg[16]} {dac_pulse_period_dbg[17]} {dac_pulse_period_dbg[18]} {dac_pulse_period_dbg[19]} {dac_pulse_period_dbg[20]} {dac_pulse_period_dbg[21]} {dac_pulse_period_dbg[22]} {dac_pulse_period_dbg[23]} {dac_pulse_period_dbg[24]} {dac_pulse_period_dbg[25]} {dac_pulse_period_dbg[26]} {dac_pulse_period_dbg[27]} {dac_pulse_period_dbg[28]} {dac_pulse_period_dbg[29]} {dac_pulse_period_dbg[30]} {dac_pulse_period_dbg[31]}]]
+connect_debug_port u_ila_2/probe3 [get_nets [list {dac_pulse_width_dbg[0]} {dac_pulse_width_dbg[1]} {dac_pulse_width_dbg[2]} {dac_pulse_width_dbg[3]} {dac_pulse_width_dbg[4]} {dac_pulse_width_dbg[5]} {dac_pulse_width_dbg[6]} {dac_pulse_width_dbg[7]} {dac_pulse_width_dbg[8]} {dac_pulse_width_dbg[9]} {dac_pulse_width_dbg[10]} {dac_pulse_width_dbg[11]} {dac_pulse_width_dbg[12]} {dac_pulse_width_dbg[13]} {dac_pulse_width_dbg[14]} {dac_pulse_width_dbg[15]} {dac_pulse_width_dbg[16]} {dac_pulse_width_dbg[17]} {dac_pulse_width_dbg[18]} {dac_pulse_width_dbg[19]} {dac_pulse_width_dbg[20]} {dac_pulse_width_dbg[21]} {dac_pulse_width_dbg[22]} {dac_pulse_width_dbg[23]} {dac_pulse_width_dbg[24]} {dac_pulse_width_dbg[25]} {dac_pulse_width_dbg[26]} {dac_pulse_width_dbg[27]} {dac_pulse_width_dbg[28]} {dac_pulse_width_dbg[29]} {dac_pulse_width_dbg[30]} {dac_pulse_width_dbg[31]}]]
+connect_debug_port u_ila_2/probe4 [get_nets [list dac_rst_dbg]]
+connect_debug_port u_ila_2/probe5 [get_nets [list dac_start_dbg]]
+
+
+connect_debug_port u_ila_1/probe7 [get_nets [list p2_wrt_OBUF]]
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 3 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {udp_ctrl_inst/eth_state[0]} {udp_ctrl_inst/eth_state[1]} {udp_ctrl_inst/eth_state[2]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 96 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {udp_ctrl_inst/cfg_bus_eth[0]} {udp_ctrl_inst/cfg_bus_eth[1]} {udp_ctrl_inst/cfg_bus_eth[2]} {udp_ctrl_inst/cfg_bus_eth[3]} {udp_ctrl_inst/cfg_bus_eth[4]} {udp_ctrl_inst/cfg_bus_eth[5]} {udp_ctrl_inst/cfg_bus_eth[6]} {udp_ctrl_inst/cfg_bus_eth[7]} {udp_ctrl_inst/cfg_bus_eth[8]} {udp_ctrl_inst/cfg_bus_eth[9]} {udp_ctrl_inst/cfg_bus_eth[10]} {udp_ctrl_inst/cfg_bus_eth[11]} {udp_ctrl_inst/cfg_bus_eth[12]} {udp_ctrl_inst/cfg_bus_eth[13]} {udp_ctrl_inst/cfg_bus_eth[14]} {udp_ctrl_inst/cfg_bus_eth[15]} {udp_ctrl_inst/cfg_bus_eth[16]} {udp_ctrl_inst/cfg_bus_eth[17]} {udp_ctrl_inst/cfg_bus_eth[18]} {udp_ctrl_inst/cfg_bus_eth[19]} {udp_ctrl_inst/cfg_bus_eth[20]} {udp_ctrl_inst/cfg_bus_eth[21]} {udp_ctrl_inst/cfg_bus_eth[22]} {udp_ctrl_inst/cfg_bus_eth[23]} {udp_ctrl_inst/cfg_bus_eth[24]} {udp_ctrl_inst/cfg_bus_eth[25]} {udp_ctrl_inst/cfg_bus_eth[26]} {udp_ctrl_inst/cfg_bus_eth[27]} {udp_ctrl_inst/cfg_bus_eth[28]} {udp_ctrl_inst/cfg_bus_eth[29]} {udp_ctrl_inst/cfg_bus_eth[30]} {udp_ctrl_inst/cfg_bus_eth[31]} {udp_ctrl_inst/cfg_bus_eth[32]} {udp_ctrl_inst/cfg_bus_eth[33]} {udp_ctrl_inst/cfg_bus_eth[34]} {udp_ctrl_inst/cfg_bus_eth[35]} {udp_ctrl_inst/cfg_bus_eth[36]} {udp_ctrl_inst/cfg_bus_eth[37]} {udp_ctrl_inst/cfg_bus_eth[38]} {udp_ctrl_inst/cfg_bus_eth[39]} {udp_ctrl_inst/cfg_bus_eth[40]} {udp_ctrl_inst/cfg_bus_eth[41]} {udp_ctrl_inst/cfg_bus_eth[42]} {udp_ctrl_inst/cfg_bus_eth[43]} {udp_ctrl_inst/cfg_bus_eth[44]} {udp_ctrl_inst/cfg_bus_eth[45]} {udp_ctrl_inst/cfg_bus_eth[46]} {udp_ctrl_inst/cfg_bus_eth[47]} {udp_ctrl_inst/cfg_bus_eth[48]} {udp_ctrl_inst/cfg_bus_eth[49]} {udp_ctrl_inst/cfg_bus_eth[50]} {udp_ctrl_inst/cfg_bus_eth[51]} {udp_ctrl_inst/cfg_bus_eth[52]} {udp_ctrl_inst/cfg_bus_eth[53]} {udp_ctrl_inst/cfg_bus_eth[54]} {udp_ctrl_inst/cfg_bus_eth[55]} {udp_ctrl_inst/cfg_bus_eth[56]} {udp_ctrl_inst/cfg_bus_eth[57]} {udp_ctrl_inst/cfg_bus_eth[58]} {udp_ctrl_inst/cfg_bus_eth[59]} {udp_ctrl_inst/cfg_bus_eth[60]} {udp_ctrl_inst/cfg_bus_eth[61]} {udp_ctrl_inst/cfg_bus_eth[62]} {udp_ctrl_inst/cfg_bus_eth[63]} {udp_ctrl_inst/cfg_bus_eth[64]} {udp_ctrl_inst/cfg_bus_eth[65]} {udp_ctrl_inst/cfg_bus_eth[66]} {udp_ctrl_inst/cfg_bus_eth[67]} {udp_ctrl_inst/cfg_bus_eth[68]} {udp_ctrl_inst/cfg_bus_eth[69]} {udp_ctrl_inst/cfg_bus_eth[70]} {udp_ctrl_inst/cfg_bus_eth[71]} {udp_ctrl_inst/cfg_bus_eth[72]} {udp_ctrl_inst/cfg_bus_eth[73]} {udp_ctrl_inst/cfg_bus_eth[74]} {udp_ctrl_inst/cfg_bus_eth[75]} {udp_ctrl_inst/cfg_bus_eth[76]} {udp_ctrl_inst/cfg_bus_eth[77]} {udp_ctrl_inst/cfg_bus_eth[78]} {udp_ctrl_inst/cfg_bus_eth[79]} {udp_ctrl_inst/cfg_bus_eth[80]} {udp_ctrl_inst/cfg_bus_eth[81]} {udp_ctrl_inst/cfg_bus_eth[82]} {udp_ctrl_inst/cfg_bus_eth[83]} {udp_ctrl_inst/cfg_bus_eth[84]} {udp_ctrl_inst/cfg_bus_eth[85]} {udp_ctrl_inst/cfg_bus_eth[86]} {udp_ctrl_inst/cfg_bus_eth[87]} {udp_ctrl_inst/cfg_bus_eth[88]} {udp_ctrl_inst/cfg_bus_eth[89]} {udp_ctrl_inst/cfg_bus_eth[90]} {udp_ctrl_inst/cfg_bus_eth[91]} {udp_ctrl_inst/cfg_bus_eth[92]} {udp_ctrl_inst/cfg_bus_eth[93]} {udp_ctrl_inst/cfg_bus_eth[94]} {udp_ctrl_inst/cfg_bus_eth[95]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 8 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {m_axis_rx_tdata[0]} {m_axis_rx_tdata[1]} {m_axis_rx_tdata[2]} {m_axis_rx_tdata[3]} {m_axis_rx_tdata[4]} {m_axis_rx_tdata[5]} {m_axis_rx_tdata[6]} {m_axis_rx_tdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 1 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list udp_ctrl_inst/axis_hs]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 1 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list udp_ctrl_inst/busy_flag_eth]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 1 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list m_axis_rx_tlast]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 1 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list m_axis_rx_tready]]
+create_debug_core u_ila_1 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_1]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_1]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_1]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_1]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_1]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_1]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_1]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_1]
+set_property port_width 1 [get_debug_ports u_ila_1/clk]
+connect_debug_port u_ila_1/clk [get_nets [list clk_wiz_ctrl_inst/inst/clk_out1]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe0]
+set_property port_width 14 [get_debug_ports u_ila_1/probe0]
+connect_debug_port u_ila_1/probe0 [get_nets [list {p2_data_OBUF[0]} {p2_data_OBUF[1]} {p2_data_OBUF[2]} {p2_data_OBUF[3]} {p2_data_OBUF[4]} {p2_data_OBUF[5]} {p2_data_OBUF[6]} {p2_data_OBUF[7]} {p2_data_OBUF[8]} {p2_data_OBUF[9]} {p2_data_OBUF[10]} {p2_data_OBUF[11]} {p2_data_OBUF[12]} {p2_data_OBUF[13]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe1]
+set_property port_width 16 [get_debug_ports u_ila_1/probe1]
+connect_debug_port u_ila_1/probe1 [get_nets [list {dac_pulse_num[0]} {dac_pulse_num[1]} {dac_pulse_num[2]} {dac_pulse_num[3]} {dac_pulse_num[4]} {dac_pulse_num[5]} {dac_pulse_num[6]} {dac_pulse_num[7]} {dac_pulse_num[8]} {dac_pulse_num[9]} {dac_pulse_num[10]} {dac_pulse_num[11]} {dac_pulse_num[12]} {dac_pulse_num[13]} {dac_pulse_num[14]} {dac_pulse_num[15]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe2]
+set_property port_width 14 [get_debug_ports u_ila_1/probe2]
+connect_debug_port u_ila_1/probe2 [get_nets [list {dac_pulse_height[0]} {dac_pulse_height[1]} {dac_pulse_height[2]} {dac_pulse_height[3]} {dac_pulse_height[4]} {dac_pulse_height[5]} {dac_pulse_height[6]} {dac_pulse_height[7]} {dac_pulse_height[8]} {dac_pulse_height[9]} {dac_pulse_height[10]} {dac_pulse_height[11]} {dac_pulse_height[12]} {dac_pulse_height[13]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe3]
+set_property port_width 32 [get_debug_ports u_ila_1/probe3]
+connect_debug_port u_ila_1/probe3 [get_nets [list {dac_pulse_period[0]} {dac_pulse_period[1]} {dac_pulse_period[2]} {dac_pulse_period[3]} {dac_pulse_period[4]} {dac_pulse_period[5]} {dac_pulse_period[6]} {dac_pulse_period[7]} {dac_pulse_period[8]} {dac_pulse_period[9]} {dac_pulse_period[10]} {dac_pulse_period[11]} {dac_pulse_period[12]} {dac_pulse_period[13]} {dac_pulse_period[14]} {dac_pulse_period[15]} {dac_pulse_period[16]} {dac_pulse_period[17]} {dac_pulse_period[18]} {dac_pulse_period[19]} {dac_pulse_period[20]} {dac_pulse_period[21]} {dac_pulse_period[22]} {dac_pulse_period[23]} {dac_pulse_period[24]} {dac_pulse_period[25]} {dac_pulse_period[26]} {dac_pulse_period[27]} {dac_pulse_period[28]} {dac_pulse_period[29]} {dac_pulse_period[30]} {dac_pulse_period[31]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe4]
+set_property port_width 32 [get_debug_ports u_ila_1/probe4]
+connect_debug_port u_ila_1/probe4 [get_nets [list {dac_pulse_width[0]} {dac_pulse_width[1]} {dac_pulse_width[2]} {dac_pulse_width[3]} {dac_pulse_width[4]} {dac_pulse_width[5]} {dac_pulse_width[6]} {dac_pulse_width[7]} {dac_pulse_width[8]} {dac_pulse_width[9]} {dac_pulse_width[10]} {dac_pulse_width[11]} {dac_pulse_width[12]} {dac_pulse_width[13]} {dac_pulse_width[14]} {dac_pulse_width[15]} {dac_pulse_width[16]} {dac_pulse_width[17]} {dac_pulse_width[18]} {dac_pulse_width[19]} {dac_pulse_width[20]} {dac_pulse_width[21]} {dac_pulse_width[22]} {dac_pulse_width[23]} {dac_pulse_width[24]} {dac_pulse_width[25]} {dac_pulse_width[26]} {dac_pulse_width[27]} {dac_pulse_width[28]} {dac_pulse_width[29]} {dac_pulse_width[30]} {dac_pulse_width[31]}]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe5]
+set_property port_width 1 [get_debug_ports u_ila_1/probe5]
+connect_debug_port u_ila_1/probe5 [get_nets [list dac_rst]]
+create_debug_port u_ila_1 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_1/probe6]
+set_property port_width 1 [get_debug_ports u_ila_1/probe6]
+connect_debug_port u_ila_1/probe6 [get_nets [list dac_start]]
+create_debug_core u_ila_2 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_2]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_2]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_2]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_2]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_2]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_2]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_2]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_2]
+set_property port_width 1 [get_debug_ports u_ila_2/clk]
+connect_debug_port u_ila_2/clk [get_nets [list clk_wiz_ctrl_inst/inst/clk_out2]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe0]
+set_property port_width 8 [get_debug_ports u_ila_2/probe0]
+connect_debug_port u_ila_2/probe0 [get_nets [list {finish_cnt[0]} {finish_cnt[1]} {finish_cnt[2]} {finish_cnt[3]} {finish_cnt[4]} {finish_cnt[5]} {finish_cnt[6]} {finish_cnt[7]}]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe1]
+set_property port_width 1 [get_debug_ports u_ila_2/probe1]
+connect_debug_port u_ila_2/probe1 [get_nets [list finish_dbg]]
+create_debug_port u_ila_2 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_2/probe2]
+set_property port_width 1 [get_debug_ports u_ila_2/probe2]
+connect_debug_port u_ila_2/probe2 [get_nets [list finish_pending]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets adc_clk]

designs/eth_generator/eth_generator.sv

@@ -0,0 +1,345 @@
+`timescale 1 ns / 1 ns
+
+module eth_generator_top #(
+    parameter int unsigned DAC_DATA_WIDTH = 14
+)(
+    input               sys_clk_p,
+    input               sys_clk_n,
+    input               rst_n,
+
+    output [3:0]        led,
+
+    output              e_reset,
+    output              e_mdc,
+    inout               e_mdio,
+
+    output [3:0]        rgmii_txd,
+    output              rgmii_txctl,
+    output              rgmii_txc,
+    input  [3:0]        rgmii_rxd,
+    input               rgmii_rxctl,
+    input               rgmii_rxc,
+
+    // DAC
+    output              p2_clk,
+    output              p2_wrt,
+    (* MARK_DEBUG="true" *) output [13:0]       p2_data
+);
+
+    // -------------------------------------------------------------------------
+    // Internal GMII-side signals
+    // -------------------------------------------------------------------------
+    wire  [7:0] gmii_txd;
+    wire        gmii_tx_en;
+    wire        gmii_tx_er;
+    wire        gmii_tx_clk;
+    wire        gmii_crs;
+    wire        gmii_col;
+    wire  [7:0] gmii_rxd_i;
+    wire        gmii_rx_dv;
+    wire        gmii_rx_er;
+    wire        gmii_rx_clk;
+
+    wire [31:0] pack_total_len;
+
+    wire        e_rx_dv;
+    wire [7:0]  e_rxd;
+    wire        e_tx_en;
+    wire [7:0]  e_txd;
+    wire        e_rst_n;
+    wire        sys_clk;
+
+    wire        duplex_mode;
+    
+
+    assign duplex_mode = 1'b1;
+
+    // -------------------------------------------------------------------------
+    // System clock buffer (200 MHz differential input)
+    // -------------------------------------------------------------------------
+    IBUFDS sys_clk_ibufgds (
+        .O  (sys_clk),
+        .I  (sys_clk_p),
+        .IB (sys_clk_n)
+    );
+
+    // -------------------------------------------------------------------------
+    // IDELAYCTRL
+    // -------------------------------------------------------------------------
+    (* IODELAY_GROUP = "rgmii_idelay_group" *)
+    IDELAYCTRL IDELAYCTRL_inst (
+        .RDY    (),
+        .REFCLK (sys_clk),
+        .RST    (1'b0)
+    );
+
+    // -------------------------------------------------------------------------
+    // Generated clocks for controller
+    // Need to create this IP in Vivado:
+    //  input : 200 MHz
+    //  output0: 130 MHz
+    //  output1: 65 MHz
+    // -------------------------------------------------------------------------
+    wire dac_clk;
+    wire adc_clk;
+    wire clk_wiz_locked;
+
+    clk_wiz_ctrl_inst clk_wiz_ctrl_inst (
+        .clk_in1   (sys_clk),
+        .reset    (~rst_n),
+        .clk_out1  (dac_clk),   // 130 MHz
+        .clk_out2  (adc_clk),   // 65 MHz
+        .locked    (clk_wiz_locked)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII <-> RGMII conversion
+    // -------------------------------------------------------------------------
+    util_gmii_to_rgmii util_gmii_to_rgmii_m0 (
+        .reset           (1'b0),
+        .rgmii_td        (rgmii_txd),
+        .rgmii_tx_ctl    (rgmii_txctl),
+        .rgmii_txc       (rgmii_txc),
+        .rgmii_rd        (rgmii_rxd),
+        .rgmii_rx_ctl    (rgmii_rxctl),
+        .gmii_rx_clk     (gmii_rx_clk),
+        .gmii_txd        (e_txd),
+        .gmii_tx_en      (e_tx_en),
+        .gmii_tx_er      (1'b0),
+        .gmii_tx_clk     (gmii_tx_clk),
+        .gmii_crs        (gmii_crs),
+        .gmii_col        (gmii_col),
+        .gmii_rxd        (gmii_rxd_i),
+        .rgmii_rxc       (rgmii_rxc),
+        .gmii_rx_dv      (gmii_rx_dv),
+        .gmii_rx_er      (gmii_rx_er),
+        .speed_selection (2'b10),
+        .duplex_mode     (duplex_mode)
+    );
+
+    // -------------------------------------------------------------------------
+    // GMII arbitration / adaptation
+    // -------------------------------------------------------------------------
+    gmii_arbi arbi_inst (
+        .clk            (gmii_tx_clk),
+        .rst_n          (rst_n),
+        .speed          (2'b10),
+        .link           (1'b1),
+        .pack_total_len (pack_total_len),
+        .e_rst_n        (e_rst_n),
+        .gmii_rx_dv     (gmii_rx_dv),
+        .gmii_rxd       (gmii_rxd_i),
+        .gmii_tx_en     (gmii_tx_en),
+        .gmii_txd       (gmii_txd),
+        .e_rx_dv        (e_rx_dv),
+        .e_rxd          (e_rxd),
+        .e_tx_en        (e_tx_en),
+        .e_txd          (e_txd)
+    );
+
+    // -------------------------------------------------------------------------
+    // axis_mac interface
+    // RX stream from Ethernet goes into controller
+    // TX stream is unused for now
+    // -------------------------------------------------------------------------
+    wire        req_ready;
+
+    reg         send_req;
+    reg  [15:0] data_length;
+
+    reg  [7:0]  s_axis_tx_tdata;
+    reg         s_axis_tx_tvalid;
+    wire        s_axis_tx_tready;
+    reg         s_axis_tx_tlast;
+
+    (* MARK_DEBUG="true" *) wire [7:0]  m_axis_rx_tdata;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tvalid;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tlast;
+    (* MARK_DEBUG="true" *) wire        m_axis_rx_tready;
+
+    // Always ready to accept RX payload bytes
+    assign m_axis_rx_tready = 1'b1;
+
+    // TX disabled
+    always @(*) begin
+        send_req        = 1'b0;
+        data_length     = 16'd0;
+        s_axis_tx_tdata = 8'd0;
+        s_axis_tx_tvalid= 1'b0;
+        s_axis_tx_tlast = 1'b0;
+    end
+
+    axis_mac axis_mac0 (
+        .gmii_tx_clk       (gmii_tx_clk),
+        .gmii_rx_clk       (gmii_rx_clk),
+        .rst_n             (e_rst_n),
+
+        .gmii_rx_dv        (e_rx_dv),
+        .gmii_rxd          (e_rxd),
+        .gmii_tx_en        (gmii_tx_en),
+        .gmii_txd          (gmii_txd),
+
+        .send_req          (send_req),
+        .data_length       (data_length),
+        .req_ready         (req_ready),
+
+        .s_axis_tx_tdata   (s_axis_tx_tdata),
+        .s_axis_tx_tvalid  (s_axis_tx_tvalid),
+        .s_axis_tx_tready  (s_axis_tx_tready),
+        .s_axis_tx_tlast   (s_axis_tx_tlast),
+
+        .m_axis_rx_tdata   (m_axis_rx_tdata),
+        .m_axis_rx_tvalid  (m_axis_rx_tvalid),
+        .m_axis_rx_tready  (m_axis_rx_tready),
+        .m_axis_rx_tlast   (m_axis_rx_tlast)
+    );
+
+    // PHY reset helper from your original example
+    reset reset_m0 (
+        .clk   (sys_clk),
+        .key1  (rst_n),
+        .rst_n (e_reset)
+    );
+
+    // MDIO lines are not driven here yet
+    assign e_mdc  = 1'b0;
+    assign e_mdio = 1'bz;
+
+    // -------------------------------------------------------------------------
+    // Controller reset
+    // Use both external reset and clk_wiz lock
+    // -------------------------------------------------------------------------
+    wire ctrl_rst_n = rst_n & clk_wiz_locked;
+
+    // -------------------------------------------------------------------------
+    // Debug finish generator (still used here, since generator doesn't have finish signal)
+    //
+    // After each adc_start pulse generates one finish pulse after some delay.
+    // This is just for first bring-up so the controller can leave busy state
+    // If you don't want this, replace with:
+    // wire finish_dbg = 1'b0;
+    // -------------------------------------------------------------------------
+    (* MARK_DEBUG="true" *) logic        finish_dbg;
+    (* MARK_DEBUG="true" *) logic [7:0]  finish_cnt;
+    (* MARK_DEBUG="true" *) logic        finish_pending;
+
+    // Controller outputs to debug
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_width;
+    (* MARK_DEBUG="true" *) wire [31:0]               dac_pulse_period;
+    (* MARK_DEBUG="true" *) wire [DAC_DATA_WIDTH-1:0] dac_pulse_height;
+    (* MARK_DEBUG="true" *) wire [15:0]               dac_pulse_num;
+
+    (* MARK_DEBUG="true" *) wire [31:0]               adc_pulse_period_dbg;
+    (* MARK_DEBUG="true" *) wire [15:0]               adc_pulse_num_dbg;
+
+    (* MARK_DEBUG="true" *) wire                      dac_start;
+    (* MARK_DEBUG="true" *) wire                      adc_start_dbg;
+    (* MARK_DEBUG="true" *) wire                      dac_rst;
+    (* MARK_DEBUG="true" *) wire                      adc_rst_dbg;
+
+    always_ff @(posedge adc_clk or negedge ctrl_rst_n) begin
+        if (!ctrl_rst_n) begin
+            finish_dbg     <= 1'b0;
+            finish_cnt     <= 8'd0;
+            finish_pending <= 1'b0;
+        end else begin
+            finish_dbg <= 1'b0;
+
+            if (adc_start_dbg) begin
+                finish_pending <= 1'b1;
+                finish_cnt     <= 8'd80;
+            end else if (finish_pending) begin
+                if (finish_cnt == 8'd0) begin
+                    finish_dbg     <= 1'b1;
+                    finish_pending <= 1'b0;
+                end else begin
+                    finish_cnt <= finish_cnt - 8'd1;
+                end
+            end
+        end
+    end
+
+    // -------------------------------------------------------------------------
+    // Controller
+    // ETH domain = gmii_rx_clk, because RX AXI master comes from axis_mac RX side
+    // -------------------------------------------------------------------------
+    control #(
+        .DAC_DATA_WIDTH(DAC_DATA_WIDTH)
+    ) udp_ctrl_inst (
+        .eth_clk_in        (gmii_rx_clk),
+        .dac_clk_in        (dac_clk),
+        .adc_clk_in        (adc_clk),
+        .rst_n             (ctrl_rst_n),
+
+        .s_axis_tdata      (m_axis_rx_tdata),
+        .s_axis_tvalid     (m_axis_rx_tvalid),
+        .s_axis_tready     (), // controller internally always ready in current version
+        .s_axis_tlast      (m_axis_rx_tlast),
+
+        .finish            (finish_dbg),
+
+        .dac_pulse_width   (dac_pulse_width),
+        .dac_pulse_period  (dac_pulse_period),
+        .dac_pulse_height  (dac_pulse_height),
+        .dac_pulse_num     (dac_pulse_num),
+
+        .adc_pulse_period  (adc_pulse_period_dbg),
+        .adc_pulse_num     (adc_pulse_num_dbg),
+
+        .dac_start         (dac_start),
+        .adc_start         (adc_start_dbg),
+
+        .dac_rst           (dac_rst),
+        .adc_rst           (adc_rst_dbg)
+    );
+
+    // -------------------------------------------------------------------------
+    // DAC
+    // -------------------------------------------------------------------------
+    generator #(
+        .DATA_WIDTH(DAC_DATA_WIDTH)
+    ) generator_inst (
+        .clk_in(dac_clk),
+        .rst(dac_rst),
+        .start(dac_start),
+        .pulse_width(dac_pulse_width),
+        .pulse_period(dac_pulse_period),
+        .pulse_height(dac_pulse_height),
+        .pulse_num(dac_pulse_num),
+        .pulse(p2_wrt ),
+        .pulse_height_out(p2_data)
+    );
+
+    // dac clk mgt
+    wire p2_clk_oddr;
+
+    ODDR #(
+        .DDR_CLK_EDGE("SAME_EDGE"),
+        .INIT(1'b0),
+        .SRTYPE("SYNC")
+    ) ODDR_p2_clk (
+        .Q (p2_clk_oddr),
+        .C (dac_clk),
+        .CE(1'b1),
+        .D1(1'b1),
+        .D2(1'b0),
+        .R (1'b0),
+        .S (1'b0)
+    );
+
+    OBUF OBUF_p2_clk (
+        .I(p2_clk_oddr),
+        .O(p2_clk)
+    );
+    
+    //assign p2_wrt = p2_clk;
+
+    // -------------------------------------------------------------------------
+    // Simple LED status
+    // -------------------------------------------------------------------------
+    assign led[0] = clk_wiz_locked;
+    assign led[1] = m_axis_rx_tvalid;
+    assign led[2] = dac_start;
+    assign led[3] = adc_rst_dbg;
+
+endmodule

designs/eth_generator/ip/clk_wiz_ctrl_inst.xci

@@ -0,0 +1,689 @@
+{
+  "schema": "xilinx.com:schema:json_instance:1.0",
+  "ip_inst": {
+    "xci_name": "clk_wiz_ctrl_inst",
+    "component_reference": "xilinx.com:ip:clk_wiz:6.0",
+    "ip_revision": "16",
+    "gen_directory": "../../../../eth_generator_top.gen/sources_1/ip/clk_wiz_ctrl_inst",
+    "parameters": {
+      "component_parameters": {
+        "Component_Name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "user", "usage": "all" } ],
+        "USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "ENABLE_CLOCK_MONITOR": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK2": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "ENABLE_USER_CLOCK3": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL0": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "Enable_PLL1": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRECISION": [ { "value": "1", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "PRIMTYPE_SEL": [ { "value": "mmcm_adv", "resolve_type": "user", "usage": "all" } ],
+        "CLOCK_MGR_TYPE": [ { "value": "auto", "resolve_type": "user", "usage": "all" } ],
+        "USE_FREQ_SYNTH": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_SPREAD_SPECTRUM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_PHASE_ALIGNMENT": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_POWER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_PHASE_SHIFT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_DYN_RECONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "user", "usage": "all" } ],
+        "PRIM_IN_FREQ": [ { "value": "200.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "user", "usage": "all" } ],
+        "PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "user", "usage": "all" } ],
+        "IN_JITTER_UNITS": [ { "value": "Units_UI", "resolve_type": "user", "usage": "all" } ],
+        "RELATIVE_INCLK": [ { "value": "REL_PRIMARY", "resolve_type": "user", "usage": "all" } ],
+        "USE_INCLK_SWITCHOVER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "user", "usage": "all" } ],
+        "SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "JITTER_OPTIONS": [ { "value": "UI", "resolve_type": "user", "usage": "all" } ],
+        "CLKIN1_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_UI_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN1_JITTER_PS": [ { "value": "50.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_USED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_USED": [ { "value": "true", "value_src": "user", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_USED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "NUM_OUT_CLKS": [ { "value": "2", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLK_OUT1_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT2_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT3_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT4_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT5_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT6_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_OUT7_USE_FINE_PS_GUI": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "user", "usage": "all" } ],
+        "CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "user", "usage": "all" } ],
+        "DADDR_PORT": [ { "value": "daddr", "resolve_type": "user", "usage": "all" } ],
+        "DCLK_PORT": [ { "value": "dclk", "resolve_type": "user", "usage": "all" } ],
+        "DRDY_PORT": [ { "value": "drdy", "resolve_type": "user", "usage": "all" } ],
+        "DWE_PORT": [ { "value": "dwe", "resolve_type": "user", "usage": "all" } ],
+        "DIN_PORT": [ { "value": "din", "resolve_type": "user", "usage": "all" } ],
+        "DOUT_PORT": [ { "value": "dout", "resolve_type": "user", "usage": "all" } ],
+        "DEN_PORT": [ { "value": "den", "resolve_type": "user", "usage": "all" } ],
+        "PSCLK_PORT": [ { "value": "psclk", "resolve_type": "user", "usage": "all" } ],
+        "PSEN_PORT": [ { "value": "psen", "resolve_type": "user", "usage": "all" } ],
+        "PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "user", "usage": "all" } ],
+        "PSDONE_PORT": [ { "value": "psdone", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "125", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "USE_MAX_I_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_MIN_O_JITTER": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "user", "usage": "all" } ],
+        "FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "user", "usage": "all" } ],
+        "PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "user", "usage": "all" } ],
+        "SUMMARY_STRINGS": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_LOCKED": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CALC_DONE": [ { "value": "empty", "resolve_type": "user", "usage": "all" } ],
+        "USE_RESET": [ { "value": "true", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_POWER_DOWN": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_STATUS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_FREEZE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLK_VALID": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_INCLK_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLKFB_STOPPED": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "RESET_PORT": [ { "value": "reset", "resolve_type": "user", "usage": "all" } ],
+        "LOCKED_PORT": [ { "value": "locked", "resolve_type": "user", "usage": "all" } ],
+        "POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "user", "usage": "all" } ],
+        "CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "user", "usage": "all" } ],
+        "STATUS_PORT": [ { "value": "STATUS", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "user", "usage": "all" } ],
+        "INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "user", "usage": "all" } ],
+        "CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "user", "usage": "all" } ],
+        "SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "SS_MOD_FREQ": [ { "value": "250", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "OVERRIDE_MMCM": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_DIVCLK_DIVIDE": [ { "value": "4", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_CLKFBOUT_MULT_F": [ { "value": "16.875", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_CASCADE": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLOCK_HOLD": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "user", "usage": "all" } ],
+        "MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_STARTUP_WAIT": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT0_DIVIDE_F": [ { "value": "6.750", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT1_DIVIDE": [ { "value": "13", "value_src": "user", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "OVERRIDE_PLL": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PLL_NOTES": [ { "value": "None", "resolve_type": "user", "usage": "all" } ],
+        "PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "user", "usage": "all" } ],
+        "PLL_CLKFBOUT_MULT": [ { "value": "4", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "user", "usage": "all" } ],
+        "PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKIN_PERIOD": [ { "value": "10.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "user", "usage": "all" } ],
+        "PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "RESET_TYPE": [ { "value": "ACTIVE_HIGH", "resolve_type": "user", "usage": "all" } ],
+        "USE_SAFE_CLOCK_STARTUP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "USE_CLOCK_SEQUENCING": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "user", "format": "long", "usage": "all" } ],
+        "USE_BOARD_FLOW": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN1_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "DIFF_CLK_IN2_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "user", "usage": "all" } ],
+        "RESET_BOARD_INTERFACE": [ { "value": "Custom", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CDDC": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "user", "usage": "all" } ],
+        "CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "user", "usage": "all" } ],
+        "ENABLE_CLKOUTPHY": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "CLKOUTPHY_REQUESTED_FREQ": [ { "value": "600.000", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_JITTER": [ { "value": "162.582", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT1_PHASE_ERROR": [ { "value": "137.238", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_JITTER": [ { "value": "185.296", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT2_PHASE_ERROR": [ { "value": "137.238", "value_src": "user", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT3_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT4_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT5_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT6_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_JITTER": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "CLKOUT7_PHASE_ERROR": [ { "value": "0.0", "resolve_type": "user", "format": "float", "usage": "all" } ],
+        "INPUT_MODE": [ { "value": "frequency", "resolve_type": "user", "usage": "all" } ],
+        "INTERFACE_SELECTION": [ { "value": "Enable_AXI", "resolve_type": "user", "usage": "all" } ],
+        "AXI_DRP": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ],
+        "PHASE_DUTY_CONFIG": [ { "value": "false", "resolve_type": "user", "format": "bool", "usage": "all" } ]
+      },
+      "model_parameters": {
+        "C_CLKOUT2_USED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USER_CLK_FREQ0": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_AUTO_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_USER_CLK_FREQ1": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ2": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USER_CLK_FREQ3": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_ENABLE_CLOCK_MONITOR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK2": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_ENABLE_USER_CLOCK3": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL0": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_Enable_PLL1": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_REF_CLK_FREQ": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRECISION": [ { "value": "1", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_USED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT1_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT2_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT3_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKOUT4_BAR": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "c_component_name": [ { "value": "clk_wiz_ctrl_inst", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLATFORM": [ { "value": "UNKNOWN", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_FREQ_SYNTH": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_PHASE_ALIGNMENT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_JITTER_SEL": [ { "value": "No_Jitter", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_MIN_POWER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MIN_O_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_MAX_I_JITTER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_PHASE_SHIFT": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OPTIMIZE_CLOCKING_STRUCTURE_EN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_SWITCHOVER": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_DYN_RECONFIG": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_SPREAD_SPECTRUM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FAST_SIMULATION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMTYPE_SEL": [ { "value": "AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_CLK_VALID": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIM_IN_FREQ": [ { "value": "200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIM_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_IN_FREQ_UNITS": [ { "value": "Units_MHz", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_IN_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_SECONDARY_IN_TIMEPERIOD": [ { "value": "10.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_FEEDBACK_SOURCE": [ { "value": "FDBK_AUTO", "resolve_type": "generated", "usage": "all" } ],
+        "C_PRIM_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_PHASESHIFT_MODE": [ { "value": "WAVEFORM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_SOURCE": [ { "value": "Single_ended_clock_capable_pin", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_SIGNALING": [ { "value": "SINGLE", "resolve_type": "generated", "usage": "all" } ],
+        "C_USE_RESET": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_RESET_LOW": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_LOCKED": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_INCLK_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLKFB_STOPPED": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_POWER_DOWN": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_STATUS": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_FREEZE": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_NUM_OUT_CLKS": [ { "value": "2", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_DRIVES": [ { "value": "BUFG", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW0": [ { "value": "Input Clock   Freq (MHz)    Input Jitter (UI)", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW1": [ { "value": "__primary_________200.000____________0.010", "resolve_type": "generated", "usage": "all" } ],
+        "C_INCLK_SUM_ROW2": [ { "value": "no_secondary_input_clock ", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0A": [ { "value": " Output     Output      Phase    Duty Cycle   Pk-to-Pk     Phase", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW0B": [ { "value": "  Clock     Freq (MHz)  (degrees)    (%)     Jitter (ps)  Error (ps)", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW1": [ { "value": "clk_out1__125.00000______0.000______50.0______162.582____137.238", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW2": [ { "value": "clk_out2__64.90385______0.000______50.0______185.296____137.238", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW3": [ { "value": "no_CLK_OUT3_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW4": [ { "value": "no_CLK_OUT4_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW5": [ { "value": "no_CLK_OUT5_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW6": [ { "value": "no_CLK_OUT6_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_OUTCLK_SUM_ROW7": [ { "value": "no_CLK_OUT7_output", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_OUT_FREQ": [ { "value": "125", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_OUT_FREQ": [ { "value": "65.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_REQUESTED_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_OUT_FREQ": [ { "value": "125.00000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_OUT_FREQ": [ { "value": "64.90385", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_OUT_FREQ": [ { "value": "100.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT1_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT2_DUTY_CYCLE": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT3_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT4_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT5_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT6_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKOUT7_DUTY_CYCLE": [ { "value": "50.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_USE_SAFE_CLOCK_STARTUP": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_USE_CLOCK_SEQUENCING": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT1_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT2_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT3_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT4_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT5_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT6_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CLKOUT7_SEQUENCE_NUMBER": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_NOTES": [ { "value": "None", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_MULT_F": [ { "value": "16.875", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN1_PERIOD": [ { "value": "5.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKIN2_PERIOD": [ { "value": "10.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_CASCADE": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_CLOCK_HOLD": [ { "value": "FALSE", "resolve_type": "generated", "format": "bool", "usage": "all" } ],
+        "C_MMCM_COMPENSATION": [ { "value": "ZHOLD", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_DIVCLK_DIVIDE": [ { "value": "4", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_REF_JITTER1": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_REF_JITTER2": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_STARTUP_WAIT": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DIVIDE_F": [ { "value": "6.750", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DIVIDE": [ { "value": "13", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_MMCM_CLKFBOUT_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT0_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT1_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT2_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT3_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT4_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT5_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCM_CLKOUT6_USE_FINE_PS": [ { "value": "FALSE", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_NOTES": [ { "value": "No notes", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_BANDWIDTH": [ { "value": "OPTIMIZED", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLK_FEEDBACK": [ { "value": "CLKFBOUT", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_MULT": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKIN_PERIOD": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_COMPENSATION": [ { "value": "SYSTEM_SYNCHRONOUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLL_DIVCLK_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_REF_JITTER": [ { "value": "0.010", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DIVIDE": [ { "value": "1", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PLL_CLKOUT0_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_DUTY_CYCLE": [ { "value": "0.500", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKFBOUT_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT0_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT1_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT2_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT3_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT4_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PLL_CLKOUT5_PHASE": [ { "value": "0.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLOCK_MGR_TYPE": [ { "value": "NA", "resolve_type": "generated", "usage": "all" } ],
+        "C_OVERRIDE_MMCM": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_OVERRIDE_PLL": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_PRIMARY_PORT": [ { "value": "clk_in1", "resolve_type": "generated", "usage": "all" } ],
+        "C_SECONDARY_PORT": [ { "value": "clk_in2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT1_PORT": [ { "value": "clk_out1", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT2_PORT": [ { "value": "clk_out2", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT3_PORT": [ { "value": "clk_out3", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT4_PORT": [ { "value": "clk_out4", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT5_PORT": [ { "value": "clk_out5", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT6_PORT": [ { "value": "clk_out6", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_OUT7_PORT": [ { "value": "clk_out7", "resolve_type": "generated", "usage": "all" } ],
+        "C_RESET_PORT": [ { "value": "reset", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCKED_PORT": [ { "value": "locked", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_PORT": [ { "value": "clkfb_in", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_P_PORT": [ { "value": "clkfb_in_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_IN_N_PORT": [ { "value": "clkfb_in_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_PORT": [ { "value": "clkfb_out", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_P_PORT": [ { "value": "clkfb_out_p", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_OUT_N_PORT": [ { "value": "clkfb_out_n", "resolve_type": "generated", "usage": "all" } ],
+        "C_POWER_DOWN_PORT": [ { "value": "power_down", "resolve_type": "generated", "usage": "all" } ],
+        "C_DADDR_PORT": [ { "value": "daddr", "resolve_type": "generated", "usage": "all" } ],
+        "C_DCLK_PORT": [ { "value": "dclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_DRDY_PORT": [ { "value": "drdy", "resolve_type": "generated", "usage": "all" } ],
+        "C_DWE_PORT": [ { "value": "dwe", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIN_PORT": [ { "value": "din", "resolve_type": "generated", "usage": "all" } ],
+        "C_DOUT_PORT": [ { "value": "dout", "resolve_type": "generated", "usage": "all" } ],
+        "C_DEN_PORT": [ { "value": "den", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSCLK_PORT": [ { "value": "psclk", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSEN_PORT": [ { "value": "psen", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSINCDEC_PORT": [ { "value": "psincdec", "resolve_type": "generated", "usage": "all" } ],
+        "C_PSDONE_PORT": [ { "value": "psdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_VALID_PORT": [ { "value": "CLK_VALID", "resolve_type": "generated", "usage": "all" } ],
+        "C_STATUS_PORT": [ { "value": "STATUS", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLK_IN_SEL_PORT": [ { "value": "clk_in_sel", "resolve_type": "generated", "usage": "all" } ],
+        "C_INPUT_CLK_STOPPED_PORT": [ { "value": "input_clk_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFB_STOPPED_PORT": [ { "value": "clkfb_stopped", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKIN1_JITTER_PS": [ { "value": "50.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_CLKIN2_JITTER_PS": [ { "value": "100.0", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_PRIMITIVE": [ { "value": "MMCM", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MODE": [ { "value": "CENTER_HIGH", "resolve_type": "generated", "usage": "all" } ],
+        "C_SS_MOD_PERIOD": [ { "value": "4000", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_SS_MOD_TIME": [ { "value": "0.004", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_HAS_CDDC": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_CDDCDONE_PORT": [ { "value": "cddcdone", "resolve_type": "generated", "usage": "all" } ],
+        "C_CDDCREQ_PORT": [ { "value": "cddcreq", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUTPHY_MODE": [ { "value": "VCO", "resolve_type": "generated", "usage": "all" } ],
+        "C_ENABLE_CLKOUTPHY": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_INTERFACE_SELECTION": [ { "value": "0", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_ADDR_WIDTH": [ { "value": "11", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_S_AXI_DATA_WIDTH": [ { "value": "32", "resolve_type": "generated", "format": "long", "usage": "all" } ],
+        "C_POWER_REG": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKFBOUT_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVCLK": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_LOCK_3": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_1": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_FILTER_2": [ { "value": "0000", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE1_AUTO": [ { "value": "1", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE2_AUTO": [ { "value": "1.9259259259259258", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE3_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE4_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE5_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE6_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_DIVIDE7_AUTO": [ { "value": "0.14814814814814814", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_PLLBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV1": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV2": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV3": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV4": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV5": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV6": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_MMCMBUFGCEDIV7": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT7_MATCHED_ROUTING": [ { "value": "false", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT0_ACTUAL_FREQ": [ { "value": "125.00000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT1_ACTUAL_FREQ": [ { "value": "64.90385", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT2_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT3_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT4_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT5_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_CLKOUT6_ACTUAL_FREQ": [ { "value": "100.000", "resolve_type": "generated", "usage": "all" } ],
+        "C_M_MAX": [ { "value": "64.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_M_MIN": [ { "value": "2.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MAX": [ { "value": "80.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_D_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MAX": [ { "value": "128.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_O_MIN": [ { "value": "1.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MIN": [ { "value": "600.000", "resolve_type": "generated", "format": "float", "usage": "all" } ],
+        "C_VCO_MAX": [ { "value": "1200.000", "resolve_type": "generated", "format": "float", "usage": "all" } ]
+      },
+      "project_parameters": {
+        "ARCHITECTURE": [ { "value": "artix7" } ],
+        "BASE_BOARD_PART": [ { "value": "" } ],
+        "BOARD_CONNECTIONS": [ { "value": "" } ],
+        "DEVICE": [ { "value": "xc7a35t" } ],
+        "PACKAGE": [ { "value": "fgg484" } ],
+        "PREFHDL": [ { "value": "VERILOG" } ],
+        "SILICON_REVISION": [ { "value": "" } ],
+        "SIMULATOR_LANGUAGE": [ { "value": "MIXED" } ],
+        "SPEEDGRADE": [ { "value": "-1" } ],
+        "STATIC_POWER": [ { "value": "" } ],
+        "TEMPERATURE_GRADE": [ { "value": "" } ]
+      },
+      "runtime_parameters": {
+        "IPCONTEXT": [ { "value": "IP_Flow" } ],
+        "IPREVISION": [ { "value": "16" } ],
+        "MANAGED": [ { "value": "TRUE" } ],
+        "OUTPUTDIR": [ { "value": "../../../../eth_generator_top.gen/sources_1/ip/clk_wiz_ctrl_inst" } ],
+        "SELECTEDSIMMODEL": [ { "value": "" } ],
+        "SHAREDDIR": [ { "value": "." } ],
+        "SWVERSION": [ { "value": "2025.1" } ],
+        "SYNTHESISFLOW": [ { "value": "OUT_OF_CONTEXT" } ]
+      }
+    },
+    "boundary": {
+      "ports": {
+        "reset": [ { "direction": "in", "driver_value": "0" } ],
+        "clk_in1": [ { "direction": "in" } ],
+        "clk_out1": [ { "direction": "out" } ],
+        "clk_out2": [ { "direction": "out" } ],
+        "locked": [ { "direction": "out" } ]
+      },
+      "interfaces": {
+        "reset": {
+          "vlnv": "xilinx.com:signal:reset:1.0",
+          "abstraction_type": "xilinx.com:signal:reset_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "POLARITY": [ { "value": "ACTIVE_HIGH", "value_src": "constant", "usage": "all" } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "RESET_BOARD_INTERFACE", "value_src": "constant", "usage": "all" } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "RST": [ { "physical_name": "reset" } ]
+          }
+        },
+        "clock_CLK_IN1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "slave",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ],
+            "BOARD.ASSOCIATED_PARAM": [ { "value": "CLK_IN1_BOARD_INTERFACE", "usage": "all", "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_IN1": [ { "physical_name": "clk_in1" } ]
+          }
+        },
+        "clock_CLK_OUT1": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT1": [ { "physical_name": "clk_out1" } ]
+          }
+        },
+        "clock_CLK_OUT2": {
+          "vlnv": "xilinx.com:signal:clock:1.0",
+          "abstraction_type": "xilinx.com:signal:clock_rtl:1.0",
+          "mode": "master",
+          "parameters": {
+            "FREQ_HZ": [ { "value": "100000000", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "FREQ_TOLERANCE_HZ": [ { "value": "0", "resolve_type": "generated", "format": "long", "is_ips_inferred": true, "is_static_object": false } ],
+            "PHASE": [ { "value": "0.0", "resolve_type": "generated", "format": "float", "is_ips_inferred": true, "is_static_object": false } ],
+            "CLK_DOMAIN": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_BUSIF": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_PORT": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "ASSOCIATED_RESET": [ { "value": "", "resolve_type": "generated", "is_ips_inferred": true, "is_static_object": false } ],
+            "INSERT_VIP": [ { "value": "0", "resolve_type": "user", "format": "long", "usage": "simulation.rtl", "is_ips_inferred": true, "is_static_object": false } ]
+          },
+          "port_maps": {
+            "CLK_OUT2": [ { "physical_name": "clk_out2" } ]
+          }
+        }
+      }
+    }
+  }
+}

rtl/controller/README.md

@@ -0,0 +1,62 @@
+# Системный контроллер
+
+Контроллер принимает входные пакеты udp с ethernet, передаваемые по axi stream, и выполняет настройку выходных регистров в соотвествии с содержимым этого пакета, а также синхронизирует сигналы между тремя clock domains - есть clk от ethernet, clk для ЦАП и clk для АЦП
+
+## Список параметров:
+- dac_data_width - битность данных ЦАП, <= 16bit
+
+## Список входных портов:
+- eth_clk_in - базовая входная частота
+- dac_clk_in - входная частота ЦАП
+- adc_clk_in - входная частота АЦП
+- rst_n - общий reset 
+- s_axis [8 bit] - AXI stream slave для приема данных от ethernet udp (уже разобранный payload по байтам) - домен eth_clk
+- finish - сигнал окончания приема данных с АЦП, домен adc_clk !
+
+## Список выходных портов:
+- dac_pulse_width[31:0] - выход pulse_width в домене dac_clk
+- dac_pulse_period[31:0] - выход pulse_period в домене dac_clk
+- dac_pulse_height[dac_data_width-1:0] - выход pulse_height в домене dac_clk
+- dac_pulse_num[15:0] - выход pulse_num в домене dac_clk
+---
+- adc_pulse_period[31:0] - выход pulse_period в домене adc_clk
+- adc_pulse_num[15:0] - выход pulse_num в домене adc_clk
+---
+- dac_start - start в домене dac_clk
+- adc_start - start в домене adc_clk
+---
+- dac_rst - rst в домене dac_clk
+- adc_rst - rst в домене adc_clk
+
+## Логика работы:
+по умолчанию после инициализации блок встает в состояние ожидания (*idle*), и становится *ready* для приема данных по axis.
+далее ждет контрольный пакет. всего есть 3 вариации контрольных пакетов (в любом порядке), получаемых по axi stream:
+```
+8'b00001111 - soft reset
+8'b11110000 - start
+8'b10001000 - set_data
+```
+
+*soft reset* отправляет пульс rst на dac_rst и adc_rst, синхронизировав пульсы в их доменах. при этом сброс самого контроллера не происходит, значения остаются как и были
+
+*start* отправляет пульс start на dac_start и adc_start в их доменах. при этом после этого блок перестает быть ready и ждет, пока не придет пульс finish, после этого он возвращается снова в *idle* состояние
+
+*set_data* значит, что следующие 96 бит = 12*8 байт, пришедшии по axis - это конфигурационная информация и ее нужно записать в внутренний регистр на 96 бит.
+
+конфигурационный регистр на 96 бит делится так:
+```
+reg[31:0] - pulse_width
+reg[63:32] - pulse_period
+reg[79:64] - pulse_num
+reg[79+dac_data_width:80] - pulse_height
+```
+
+соотвественно эти записанные значения выставляются на соотвествующие выходные сигналы в доменах dac_clk и adc_clk. выходы обновляются каждый раз, когда происходит set_data, и сигналы сохраняют своё значение до следующего set_data.
+
+## Симуляция
+Тесты запускаются автоматически через make.
+```
+cd tests
+make sim
+```
+Должно выдать "All tests done" в конце симуляции.

rtl/controller/src/controller.sv

@@ -0,0 +1,462 @@
+module control #(
+    parameter int unsigned DAC_DATA_WIDTH = 12
+) (
+    input  logic                       eth_clk_in,
+    input  logic                       dac_clk_in,
+    input  logic                       adc_clk_in,
+    input  logic                       rst_n,
+
+    // AXI stream slave, eth_clk_in domain
+    input  logic [7:0]                 s_axis_tdata,
+    input  logic                       s_axis_tvalid,
+    output logic                       s_axis_tready,
+    input  logic                       s_axis_tlast,
+
+    // adc_clk_in domain
+    input  logic                       finish,
+
+    // dac_clk_in domain outputs
+    output logic [31:0]                dac_pulse_width,
+    output logic [31:0]                dac_pulse_period,
+    output logic [DAC_DATA_WIDTH-1:0]  dac_pulse_height,
+    output logic [15:0]                dac_pulse_num,
+
+    // adc_clk_in domain outputs
+    output logic [31:0]                adc_pulse_period,
+    output logic [15:0]                adc_pulse_num,
+
+    // pulse outputs
+    output logic                       dac_start,
+    output logic                       adc_start,
+    output logic                       dac_rst,
+    output logic                       adc_rst
+);
+
+    // static checks
+    initial begin
+        if (DAC_DATA_WIDTH > 16) begin
+            $error("DAC_DATA_WIDTH must be <= 16");
+        end
+        if (DAC_DATA_WIDTH == 0) begin
+            $error("DAC_DATA_WIDTH must be > 0");
+        end
+    end
+
+    // command constants
+    localparam logic [7:0] CMD_SOFT_RESET = 8'h0F;
+    localparam logic [7:0] CMD_START      = 8'hF0;
+    localparam logic [7:0] CMD_SET_DATA   = 8'h88;
+
+    // reset synchronizers: async assert, sync deassert in each domain
+    logic eth_rst_ff1, eth_rst_ff2;
+    logic dac_rst_ff1, dac_rst_ff2;
+    logic adc_rst_ff1, adc_rst_ff2;
+
+    logic eth_rst;
+    logic dac_rst_int;
+    logic adc_rst_int;
+
+    always_ff @(posedge eth_clk_in or negedge rst_n) begin
+        if (!rst_n) begin
+            eth_rst_ff1 <= 1'b1;
+            eth_rst_ff2 <= 1'b1;
+        end else begin
+            eth_rst_ff1 <= 1'b0;
+            eth_rst_ff2 <= eth_rst_ff1;
+        end
+    end
+
+    always_ff @(posedge dac_clk_in or negedge rst_n) begin
+        if (!rst_n) begin
+            dac_rst_ff1 <= 1'b1;
+            dac_rst_ff2 <= 1'b1;
+        end else begin
+            dac_rst_ff1 <= 1'b0;
+            dac_rst_ff2 <= dac_rst_ff1;
+        end
+    end
+
+    always_ff @(posedge adc_clk_in or negedge rst_n) begin
+        if (!rst_n) begin
+            adc_rst_ff1 <= 1'b1;
+            adc_rst_ff2 <= 1'b1;
+        end else begin
+            adc_rst_ff1 <= 1'b0;
+            adc_rst_ff2 <= adc_rst_ff1;
+        end
+    end
+
+    assign eth_rst     = eth_rst_ff2;
+    assign dac_rst_int = dac_rst_ff2;
+    assign adc_rst_int = adc_rst_ff2;
+
+    // axi stream is always accepted. If packet is not needed, it is discarded.
+    assign s_axis_tready = 1'b1;
+
+    (* MARK_DEBUG="true" *) wire axis_hs = s_axis_tvalid & s_axis_tready;
+
+    // -------------------------------------------------------------------------
+    // Shared 96-bit config bus in ETH domain
+    //
+    // Byte order for SET_DATA payload, little-endian:
+    // payload byte 0  -> cfg_bus_eth[7:0]
+    // payload byte 1  -> cfg_bus_eth[15:8]
+    // ...etc...
+    // payload byte 11 -> cfg_bus_eth[95:88]
+    //
+    // Field layout inside cfg_bus_eth:
+    // [31:0]   pulse_width
+    // [63:32]  pulse_period
+    // [79:64]  pulse_num
+    // [95:80]  pulse_height_raw[15:0]
+    // -------------------------------------------------------------------------
+    (* MARK_DEBUG="true" *) logic [95:0] cfg_bus_eth;
+    logic [95:0] cfg_shift_eth;
+
+    // ETH-domain parser and control
+    typedef enum logic [2:0] {
+        ST_IDLE         = 3'd0,
+        ST_RECV_CFG     = 3'd1,
+        ST_WAIT_CFG_ACK = 3'd2,
+        ST_DISCARD      = 3'd3
+    } eth_state_t;
+
+    (* MARK_DEBUG="true" *) eth_state_t eth_state;
+
+    logic [3:0] cfg_byte_cnt;
+
+    // Busy flag: set by START command, cleared by finish event from ADC domain
+    (* MARK_DEBUG="true" *) logic busy_flag_eth;
+
+    // Pending ACKs for config delivery
+    logic cfg_wait_dac_ack;
+    logic cfg_wait_adc_ack;
+
+    // Event toggles ETH -> DAC/ADC
+    logic start_toggle_eth;
+    logic rst_toggle_eth;
+
+    // Config request toggles ETH -> DAC/ADC
+    logic cfg_req_toggle_dac_eth;
+    logic cfg_req_toggle_adc_eth;
+
+    // ACK toggles DAC/ADC -> ETH
+    logic cfg_ack_toggle_dac;
+    logic cfg_ack_toggle_adc;
+
+    (* ASYNC_REG = "TRUE" *) logic cfg_ack_toggle_dac_meta, cfg_ack_toggle_dac_sync, cfg_ack_toggle_dac_sync_d;
+    (* ASYNC_REG = "TRUE" *) logic cfg_ack_toggle_adc_meta, cfg_ack_toggle_adc_sync, cfg_ack_toggle_adc_sync_d;
+
+    wire cfg_ack_pulse_dac_eth = cfg_ack_toggle_dac_sync ^ cfg_ack_toggle_dac_sync_d;
+    wire cfg_ack_pulse_adc_eth = cfg_ack_toggle_adc_sync ^ cfg_ack_toggle_adc_sync_d;
+
+    always_ff @(posedge eth_clk_in or posedge eth_rst) begin
+        if (eth_rst) begin
+            cfg_ack_toggle_dac_meta   <= 1'b0;
+            cfg_ack_toggle_dac_sync   <= 1'b0;
+            cfg_ack_toggle_dac_sync_d <= 1'b0;
+
+            cfg_ack_toggle_adc_meta   <= 1'b0;
+            cfg_ack_toggle_adc_sync   <= 1'b0;
+            cfg_ack_toggle_adc_sync_d <= 1'b0;
+        end else begin
+            cfg_ack_toggle_dac_meta   <= cfg_ack_toggle_dac;
+            cfg_ack_toggle_dac_sync   <= cfg_ack_toggle_dac_meta;
+            cfg_ack_toggle_dac_sync_d <= cfg_ack_toggle_dac_sync;
+
+            cfg_ack_toggle_adc_meta   <= cfg_ack_toggle_adc;
+            cfg_ack_toggle_adc_sync   <= cfg_ack_toggle_adc_meta;
+            cfg_ack_toggle_adc_sync_d <= cfg_ack_toggle_adc_sync;
+        end
+    end
+
+    // finish event: ADC -> ETH via toggle CDC
+    logic finish_toggle_adc;
+    logic finish_meta_eth, finish_sync_eth, finish_sync_eth_d;
+
+    wire finish_pulse_eth = finish_sync_eth ^ finish_sync_eth_d;
+
+    always_ff @(posedge adc_clk_in or posedge adc_rst_int) begin
+        if (adc_rst_int) begin
+            finish_toggle_adc <= 1'b0;
+        end else if (finish) begin
+            finish_toggle_adc <= ~finish_toggle_adc;
+        end
+    end
+
+    always_ff @(posedge eth_clk_in or posedge eth_rst) begin
+        if (eth_rst) begin
+            finish_meta_eth   <= 1'b0;
+            finish_sync_eth   <= 1'b0;
+            finish_sync_eth_d <= 1'b0;
+        end else begin
+            finish_meta_eth   <= finish_toggle_adc;
+            finish_sync_eth   <= finish_meta_eth;
+            finish_sync_eth_d <= finish_sync_eth;
+        end
+    end
+
+    // ETH FSM
+    always_ff @(posedge eth_clk_in or posedge eth_rst) begin
+        if (eth_rst) begin
+            eth_state              <= ST_IDLE;
+            cfg_byte_cnt           <= '0;
+            cfg_shift_eth          <= '0;
+            cfg_bus_eth            <= '0;
+
+            busy_flag_eth          <= 1'b0;
+
+            start_toggle_eth       <= 1'b0;
+            rst_toggle_eth         <= 1'b0;
+
+            cfg_req_toggle_dac_eth <= 1'b0;
+            cfg_req_toggle_adc_eth <= 1'b0;
+
+            cfg_wait_dac_ack       <= 1'b0;
+            cfg_wait_adc_ack       <= 1'b0;
+        end else begin
+            // finish always clears busy
+            if (finish_pulse_eth) begin
+                busy_flag_eth <= 1'b0;
+            end
+
+            // config acks
+            if (cfg_ack_pulse_dac_eth) begin
+                cfg_wait_dac_ack <= 1'b0;
+            end
+            if (cfg_ack_pulse_adc_eth) begin
+                cfg_wait_adc_ack <= 1'b0;
+            end
+
+            case (eth_state)
+                ST_IDLE: begin
+                    cfg_byte_cnt  <= '0;
+                    cfg_shift_eth <= cfg_shift_eth;
+
+                    if (axis_hs) begin
+                        // if busy, drop the whole packet
+                        if (busy_flag_eth) begin
+                            if (!s_axis_tlast) begin
+                                eth_state <= ST_DISCARD;
+                            end
+                        end else begin
+                            unique case (s_axis_tdata)
+                                CMD_SOFT_RESET: begin
+                                    rst_toggle_eth <= ~rst_toggle_eth;
+                                end
+
+                                CMD_START: begin
+                                    start_toggle_eth <= ~start_toggle_eth;
+                                    busy_flag_eth    <= 1'b1;
+                                end
+
+                                CMD_SET_DATA: begin
+                                    // expect exactly 12 bytes after command
+                                    if (s_axis_tlast) begin
+                                        // no payload, invalid packet
+                                        eth_state <= ST_IDLE;
+                                    end else begin
+                                        cfg_byte_cnt  <= 4'd0;
+                                        cfg_shift_eth <= '0;
+                                        eth_state     <= ST_RECV_CFG;
+                                    end
+                                end
+
+                                default: begin
+                                    // unknown command: discard packet remainder if any
+                                    if (!s_axis_tlast) begin
+                                        eth_state <= ST_DISCARD;
+                                    end
+                                end
+                            endcase
+                        end
+                    end
+                end
+
+                ST_RECV_CFG: begin
+                    if (axis_hs) begin
+                        // little endian packing
+                        cfg_shift_eth[cfg_byte_cnt*8 +: 8] <= s_axis_tdata;
+
+                        if (cfg_byte_cnt == 4'd11) begin
+                            // this must be the final payload byte
+                            if (s_axis_tlast) begin
+                                cfg_bus_eth            <= {s_axis_tdata, cfg_shift_eth[87:0]};
+                                cfg_req_toggle_dac_eth <= ~cfg_req_toggle_dac_eth;
+                                cfg_req_toggle_adc_eth <= ~cfg_req_toggle_adc_eth;
+                                cfg_wait_dac_ack       <= 1'b1;
+                                cfg_wait_adc_ack       <= 1'b1;
+                                eth_state              <= ST_WAIT_CFG_ACK;
+                            end else begin
+                                // too many bytes in packet
+                                eth_state <= ST_DISCARD;
+                            end
+                        end else begin
+                            // early tlast means packet too short!!
+                            if (s_axis_tlast) begin
+                                eth_state <= ST_IDLE;
+                            end else begin
+                                cfg_byte_cnt <= cfg_byte_cnt + 4'd1;
+                            end
+                        end
+                    end
+                end
+
+                ST_WAIT_CFG_ACK: begin
+                    // any incoming packet while waiting ack is discarded
+                    if (cfg_ack_pulse_dac_eth || cfg_ack_pulse_adc_eth) begin
+                        if ((~cfg_wait_dac_ack || cfg_ack_pulse_dac_eth) &&
+                            (~cfg_wait_adc_ack || cfg_ack_pulse_adc_eth)) begin
+                            eth_state <= ST_IDLE;
+                        end
+                    end
+
+                    if (axis_hs && !s_axis_tlast) begin
+                        eth_state <= ST_DISCARD;
+                    end
+                end
+
+                ST_DISCARD: begin
+                    if (axis_hs && s_axis_tlast) begin
+                        eth_state <= ST_IDLE;
+                    end
+                end
+
+                default: begin
+                    eth_state <= ST_IDLE;
+                end
+            endcase
+        end
+    end
+
+    // ETH -> DAC: start/reset event sync
+    (* ASYNC_REG = "TRUE" *) logic start_meta_dac, start_sync_dac;
+    logic start_sync_dac_d;
+    (* ASYNC_REG = "TRUE" *) logic rst_meta_dac,   rst_sync_dac;
+    logic rst_sync_dac_d;
+
+    wire dac_start_pulse = start_sync_dac ^ start_sync_dac_d;
+    wire dac_rst_pulse   = rst_sync_dac   ^ rst_sync_dac_d;
+
+    always_ff @(posedge dac_clk_in or posedge dac_rst_int) begin
+        if (dac_rst_int) begin
+            start_meta_dac   <= 1'b0;
+            start_sync_dac   <= 1'b0;
+            start_sync_dac_d <= 1'b0;
+
+            rst_meta_dac     <= 1'b0;
+            rst_sync_dac     <= 1'b0;
+            rst_sync_dac_d   <= 1'b0;
+
+            dac_start        <= 1'b0;
+            dac_rst          <= 1'b0;
+        end else begin
+            start_meta_dac   <= start_toggle_eth;
+            start_sync_dac   <= start_meta_dac;
+            start_sync_dac_d <= start_sync_dac;
+
+            rst_meta_dac     <= rst_toggle_eth;
+            rst_sync_dac     <= rst_meta_dac;
+            rst_sync_dac_d   <= rst_sync_dac;
+
+            dac_start        <= dac_start_pulse;
+            dac_rst          <= dac_rst_pulse;
+        end
+    end
+
+    // ETH -> ADC: start/reset event sync
+    (* ASYNC_REG = "TRUE" *) logic start_meta_adc, start_sync_adc;
+    logic start_sync_adc_d;
+    (* ASYNC_REG = "TRUE" *) logic rst_meta_adc,   rst_sync_adc;
+    logic rst_sync_adc_d;
+
+    wire adc_start_pulse = start_sync_adc ^ start_sync_adc_d;
+    wire adc_rst_pulse   = rst_sync_adc   ^ rst_sync_adc_d;
+
+    always_ff @(posedge adc_clk_in or posedge adc_rst_int) begin
+        if (adc_rst_int) begin
+            start_meta_adc   <= 1'b0;
+            start_sync_adc   <= 1'b0;
+            start_sync_adc_d <= 1'b0;
+
+            rst_meta_adc     <= 1'b0;
+            rst_sync_adc     <= 1'b0;
+            rst_sync_adc_d   <= 1'b0;
+
+            adc_start        <= 1'b0;
+            adc_rst          <= 1'b0;
+        end else begin
+            start_meta_adc   <= start_toggle_eth;
+            start_sync_adc   <= start_meta_adc;
+            start_sync_adc_d <= start_sync_adc;
+
+            rst_meta_adc     <= rst_toggle_eth;
+            rst_sync_adc     <= rst_meta_adc;
+            rst_sync_adc_d   <= rst_sync_adc;
+
+            adc_start        <= adc_start_pulse;
+            adc_rst          <= adc_rst_pulse;
+        end
+    end
+
+    // ETH -> DAC config CDC
+    // cfg_bus_eth is kept stable in ETH domain until DAC and ADC both ACK.
+    (* ASYNC_REG = "TRUE" *) logic cfg_req_meta_dac, cfg_req_sync_dac;
+    logic cfg_req_sync_dac_d;
+    wire  cfg_req_pulse_dac = cfg_req_sync_dac ^ cfg_req_sync_dac_d;
+
+    always_ff @(posedge dac_clk_in or posedge dac_rst_int) begin
+        if (dac_rst_int) begin
+            cfg_req_meta_dac  <= 1'b0;
+            cfg_req_sync_dac  <= 1'b0;
+            cfg_req_sync_dac_d<= 1'b0;
+            cfg_ack_toggle_dac<= 1'b0;
+
+            dac_pulse_width   <= '0;
+            dac_pulse_period  <= '0;
+            dac_pulse_num     <= '0;
+            dac_pulse_height  <= '0;
+        end else begin
+            cfg_req_meta_dac   <= cfg_req_toggle_dac_eth;
+            cfg_req_sync_dac   <= cfg_req_meta_dac;
+            cfg_req_sync_dac_d <= cfg_req_sync_dac;
+
+            if (cfg_req_pulse_dac) begin
+                dac_pulse_width  <= cfg_bus_eth[31:0];
+                dac_pulse_period <= cfg_bus_eth[63:32];
+                dac_pulse_num    <= cfg_bus_eth[79:64];
+                dac_pulse_height <= cfg_bus_eth[80 +: DAC_DATA_WIDTH];
+
+                cfg_ack_toggle_dac <= ~cfg_ack_toggle_dac;
+            end
+        end
+    end
+
+    // ETH -> ADC config CDC
+    logic cfg_req_meta_adc, cfg_req_sync_adc, cfg_req_sync_adc_d;
+    wire  cfg_req_pulse_adc = cfg_req_sync_adc ^ cfg_req_sync_adc_d;
+
+    always_ff @(posedge adc_clk_in or posedge adc_rst_int) begin
+        if (adc_rst_int) begin
+            cfg_req_meta_adc   <= 1'b0;
+            cfg_req_sync_adc   <= 1'b0;
+            cfg_req_sync_adc_d <= 1'b0;
+            cfg_ack_toggle_adc <= 1'b0;
+
+            adc_pulse_period   <= '0;
+            adc_pulse_num      <= '0;
+        end else begin
+            cfg_req_meta_adc   <= cfg_req_toggle_adc_eth;
+            cfg_req_sync_adc   <= cfg_req_meta_adc;
+            cfg_req_sync_adc_d <= cfg_req_sync_adc;
+
+            if (cfg_req_pulse_adc) begin
+                adc_pulse_period <= cfg_bus_eth[63:32];
+                adc_pulse_num    <= cfg_bus_eth[79:64];
+
+                cfg_ack_toggle_adc <= ~cfg_ack_toggle_adc;
+            end
+        end
+    end
+
+endmodule

rtl/controller/tests/Makefile

@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: MIT
+#
+# Copyright (c) 2025 FPGA Ninja, LLC
+#
+# Authors:
+# - Alex Forencich
+#
+
+# FPGA settings
+FPGA_PART = xc7a35tfgg484-1
+FPGA_TOP = control
+FPGA_ARCH = artix7
+
+RTL_DIR = ../src
+
+
+include ../../../scripts/vivado.mk
+
+SYN_FILES += $(sort $(shell find ../src -type f \( -name '*.v' -o -name '*.sv' \)))
+
+XCI_FILES = $(sort $(shell find ../src -type f -name '*.xci'))
+
+XDC_FILES += ../../../constraints/ax7a035b.xdc
+XDC_FILES += test_timing.xdc
+
+SYN_FILES += controller_tb.sv
+SIM_TOP = control_tb
+
+
+program: $(PROJECT).bit
+	echo "open_hw_manager" > program.tcl
+	echo "connect_hw_server" >> program.tcl
+	echo "open_hw_target" >> program.tcl
+	echo "current_hw_device [lindex [get_hw_devices] 0]" >> program.tcl
+	echo "refresh_hw_device -update_hw_probes false [current_hw_device]" >> program.tcl
+	echo "set_property PROGRAM.FILE {$(PROJECT).bit} [current_hw_device]" >> program.tcl
+	echo "program_hw_devices [current_hw_device]" >> program.tcl
+	echo "exit" >> program.tcl
+	vivado -nojournal -nolog -mode batch -source program.tcl
+
+$(PROJECT).mcs $(PROJECT).prm: $(PROJECT).bit
+	echo "write_cfgmem -force -format mcs -size 16 -interface SPIx4 -loadbit {up 0x0000000 $*.bit} -checksum -file $*.mcs" > generate_mcs.tcl
+	echo "exit" >> generate_mcs.tcl
+	vivado -nojournal -nolog -mode batch -source generate_mcs.tcl
+	mkdir -p rev
+	COUNT=100; \
+	while [ -e rev/$*_rev$$COUNT.bit ]; \
+	do COUNT=$$((COUNT+1)); done; \
+	COUNT=$$((COUNT-1)); \
+	for x in .mcs .prm; \
+	do cp $*$$x rev/$*_rev$$COUNT$$x; \
+	echo "Output: rev/$*_rev$$COUNT$$x"; done;

rtl/controller/tests/controller_tb.sv

@@ -0,0 +1,377 @@
+`timescale 1ns/1ps
+
+module tb_control;
+
+    localparam int unsigned DAC_DATA_WIDTH = 12;
+
+    
+    // Clocks / reset
+    logic eth_clk_in;
+    logic dac_clk_in;
+    logic adc_clk_in;
+    logic rst_n;
+
+    // axi stream (input)
+    logic [7:0] s_axis_tdata;
+    logic       s_axis_tvalid;
+    logic       s_axis_tready;
+    logic       s_axis_tlast;
+
+    // ADC side input
+    logic finish;
+
+    // DUT outputs
+    logic [31:0]                dac_pulse_width;
+    logic [31:0]                dac_pulse_period;
+    logic [DAC_DATA_WIDTH-1:0]  dac_pulse_height;
+    logic [15:0]                dac_pulse_num;
+
+    logic [31:0]                adc_pulse_period;
+    logic [15:0]                adc_pulse_num;
+
+    logic dac_start;
+    logic adc_start;
+    logic dac_rst;
+    logic adc_rst;
+
+    
+    // DUT
+    control #(
+        .DAC_DATA_WIDTH(DAC_DATA_WIDTH)
+    ) dut (
+        .eth_clk_in        (eth_clk_in),
+        .dac_clk_in        (dac_clk_in),
+        .adc_clk_in        (adc_clk_in),
+        .rst_n             (rst_n),
+
+        .s_axis_tdata      (s_axis_tdata),
+        .s_axis_tvalid     (s_axis_tvalid),
+        .s_axis_tready     (s_axis_tready),
+        .s_axis_tlast      (s_axis_tlast),
+
+        .finish            (finish),
+
+        .dac_pulse_width   (dac_pulse_width),
+        .dac_pulse_period  (dac_pulse_period),
+        .dac_pulse_height  (dac_pulse_height),
+        .dac_pulse_num     (dac_pulse_num),
+
+        .adc_pulse_period  (adc_pulse_period),
+        .adc_pulse_num     (adc_pulse_num),
+
+        .dac_start         (dac_start),
+        .adc_start         (adc_start),
+        .dac_rst           (dac_rst),
+        .adc_rst           (adc_rst)
+    );
+
+    
+    // Clock generation
+    initial begin
+        eth_clk_in = 1'b0;
+        forever #(1 * 4.000) eth_clk_in = ~eth_clk_in;   // 125 MHz
+    end
+
+    initial begin
+        dac_clk_in = 1'b0;
+        forever #(1 * 3.846153846) dac_clk_in = ~dac_clk_in; // ~130 MHz
+    end
+
+    initial begin
+        adc_clk_in = 1'b0;
+        forever #(1 * 7.692307692) adc_clk_in = ~adc_clk_in; // ~65 MHz
+    end
+
+    
+    // pulse counters and monitors for testing
+    int dac_rst_count;
+    int adc_rst_count;
+    int dac_start_count;
+    int adc_start_count;
+
+    always_ff @(posedge dac_clk_in) begin
+        if (!rst_n) begin
+            dac_rst_count   <= 0;
+            dac_start_count <= 0;
+        end else begin
+            if (dac_rst)   dac_rst_count   <= dac_rst_count + 1;
+            if (dac_start) dac_start_count <= dac_start_count + 1;
+        end
+    end
+
+    always_ff @(posedge adc_clk_in) begin
+        if (!rst_n) begin
+            adc_rst_count   <= 0;
+            adc_start_count <= 0;
+        end else begin
+            if (adc_rst)   adc_rst_count   <= adc_rst_count + 1;
+            if (adc_start) adc_start_count <= adc_start_count + 1;
+        end
+    end
+
+    
+    // some helpers for axi
+    task automatic axis_send_byte(input logic [7:0] data, input logic last);
+        begin
+            @(negedge eth_clk_in);
+            s_axis_tdata  <= data;
+            s_axis_tvalid <= 1'b1;
+            s_axis_tlast  <= last;
+
+            @(posedge eth_clk_in);
+            while (!s_axis_tready) begin
+                @(posedge eth_clk_in);
+            end
+
+            s_axis_tvalid <= 1'b0;
+            s_axis_tlast  <= 1'b0;
+            s_axis_tdata  <= '0;
+        end
+    endtask
+
+    task automatic send_cmd(input logic [7:0] cmd);
+        begin
+            axis_send_byte(cmd, 1'b1);
+        end
+    endtask
+
+    task automatic send_set_data(
+        input logic [31:0] pulse_width,
+        input logic [31:0] pulse_period,
+        input logic [15:0] pulse_num,
+        input logic [15:0] pulse_height_raw
+    );
+        logic [95:0] payload;
+        int i;
+        begin
+            // little-endian payload layout:
+            // [31:0]   pulse_width
+            // [63:32]  pulse_period
+            // [79:64]  pulse_num
+            // [95:80]  pulse_height_raw
+            payload = {pulse_height_raw, pulse_num, pulse_period, pulse_width};
+
+            axis_send_byte(8'h88, 1'b0); // CMD_SET_DATA
+
+            for (i = 0; i < 12; i++) begin
+                axis_send_byte(payload[i*8 +: 8], (i == 11));
+            end
+        end
+    endtask
+
+    task automatic pulse_finish;
+        begin
+            @(posedge adc_clk_in);
+            finish <= 1'b1;
+            @(posedge adc_clk_in);
+            finish <= 1'b0;
+        end
+    endtask
+
+    
+    // waiters
+    task automatic wait_dac_rst_count(input int expected, input int max_cycles = 100);
+        int i;
+        begin
+            for (i = 0; i < max_cycles; i++) begin
+                @(posedge dac_clk_in);
+                if (dac_rst_count >= expected) return;
+            end
+            $fatal(1, "Timeout waiting for dac_rst_count >= %0d, current=%0d", expected, dac_rst_count);
+        end
+    endtask
+
+    task automatic wait_adc_rst_count(input int expected, input int max_cycles = 100);
+        int i;
+        begin
+            for (i = 0; i < max_cycles; i++) begin
+                @(posedge adc_clk_in);
+                if (adc_rst_count >= expected) return;
+            end
+            $fatal(1, "Timeout waiting for adc_rst_count >= %0d, current=%0d", expected, adc_rst_count);
+        end
+    endtask
+
+    task automatic wait_dac_start_count(input int expected, input int max_cycles = 100);
+        int i;
+        begin
+            for (i = 0; i < max_cycles; i++) begin
+                @(posedge dac_clk_in);
+                if (dac_start_count >= expected) return;
+            end
+            $fatal(1, "Timeout waiting for dac_start_count >= %0d, current=%0d", expected, dac_start_count);
+        end
+    endtask
+
+    task automatic wait_adc_start_count(input int expected, input int max_cycles = 100);
+        int i;
+        begin
+            for (i = 0; i < max_cycles; i++) begin
+                @(posedge adc_clk_in);
+                if (adc_start_count >= expected) return;
+            end
+            $fatal(1, "Timeout waiting for adc_start_count >= %0d, current=%0d", expected, adc_start_count);
+        end
+    endtask
+
+    task automatic wait_cfg_applied(
+        input logic [31:0] exp_pulse_width,
+        input logic [31:0] exp_pulse_period,
+        input logic [15:0] exp_pulse_num,
+        input logic [15:0] exp_pulse_height_raw,
+        input int max_cycles = 200
+    );
+        logic [DAC_DATA_WIDTH-1:0] exp_dac_height;
+        int i;
+        begin
+            exp_dac_height = exp_pulse_height_raw[DAC_DATA_WIDTH-1:0];
+
+            for (i = 0; i < max_cycles; i++) begin
+                @(posedge eth_clk_in);
+                if ((dac_pulse_width  === exp_pulse_width ) &&
+                    (dac_pulse_period === exp_pulse_period) &&
+                    (dac_pulse_num    === exp_pulse_num   ) &&
+                    (dac_pulse_height === exp_dac_height  ) &&
+                    (adc_pulse_period === exp_pulse_period) &&
+                    (adc_pulse_num    === exp_pulse_num   )) begin
+                    return;
+                end
+            end
+
+            $fatal(1,
+                "Timeout waiting config outputs. Got: dac_width=%h dac_period=%h dac_num=%h dac_height=%h adc_period=%h adc_num=%h",
+                dac_pulse_width, dac_pulse_period, dac_pulse_num, dac_pulse_height,
+                adc_pulse_period, adc_pulse_num
+            );
+        end
+    endtask
+
+    
+    // Test sequence
+    logic [31:0] test_pulse_width;
+    logic [31:0] test_pulse_period;
+    logic [15:0] test_pulse_num;
+    logic [15:0] test_pulse_height_raw;
+
+    initial begin
+        // defaults
+        rst_n         = 1'b0;
+        s_axis_tdata  = '0;
+        s_axis_tvalid = 1'b0;
+        s_axis_tlast  = 1'b0;
+        finish        = 1'b0;
+
+        test_pulse_width      = 32'h11223344;
+        test_pulse_period     = 32'h55667788;
+        test_pulse_num        = 16'hA1B2;
+        test_pulse_height_raw = 16'h0CDE; // for DAC_DATA_WIDTH=12 => 12'hCDE
+
+        repeat (10) @(posedge eth_clk_in);
+        rst_n = 1'b1;
+
+        repeat (10) @(posedge eth_clk_in);
+
+        $display("[%0t] TEST 1: soft_reset", $time);
+        send_cmd(8'h0F);
+
+        wait_dac_rst_count(1);
+        wait_adc_rst_count(1);
+
+        if (dac_rst_count != 1) begin
+            $fatal(1, "Expected exactly one dac_rst pulse after first soft_reset, got %0d", dac_rst_count);
+        end
+        if (adc_rst_count != 1) begin
+            $fatal(1, "Expected exactly one adc_rst pulse after first soft_reset, got %0d", adc_rst_count);
+        end
+
+        $display("[%0t] TEST 1 passed", $time);
+
+        $display("[%0t] TEST 2: set_data", $time);
+        send_set_data(
+            test_pulse_width,
+            test_pulse_period,
+            test_pulse_num,
+            test_pulse_height_raw
+        );
+
+        wait_cfg_applied(
+            test_pulse_width,
+            test_pulse_period,
+            test_pulse_num,
+            test_pulse_height_raw
+        );
+
+        if (dac_pulse_width !== 32'h11223344) begin
+            $fatal(1, "dac_pulse_width mismatch: got %h expected %h", dac_pulse_width, 32'h11223344);
+        end
+        if (dac_pulse_period !== 32'h55667788) begin
+            $fatal(1, "dac_pulse_period mismatch: got %h expected %h", dac_pulse_period, 32'h55667788);
+        end
+        if (dac_pulse_num !== 16'hA1B2) begin
+            $fatal(1, "dac_pulse_num mismatch: got %h expected %h", dac_pulse_num, 16'hA1B2);
+        end
+        if (dac_pulse_height !== 12'hCDE) begin
+            $fatal(1, "dac_pulse_height mismatch: got %h expected %h", dac_pulse_height, 12'hCDE);
+        end
+        if (adc_pulse_period !== 32'h55667788) begin
+            $fatal(1, "adc_pulse_period mismatch: got %h expected %h", adc_pulse_period, 32'h55667788);
+        end
+        if (adc_pulse_num !== 16'hA1B2) begin
+            $fatal(1, "adc_pulse_num mismatch: got %h expected %h", adc_pulse_num, 16'hA1B2);
+        end
+
+        $display("[%0t] TEST 2 passed", $time);
+        
+        repeat (20) @(posedge eth_clk_in);
+
+        $display("[%0t] TEST 3: start", $time);
+        send_cmd(8'hF0);
+
+        wait_dac_start_count(1);
+        wait_adc_start_count(1);
+
+        if (dac_start_count != 1) begin
+            $fatal(1, "Expected exactly one dac_start pulse after first start, got %0d", dac_start_count);
+        end
+        if (adc_start_count != 1) begin
+            $fatal(1, "Expected exactly one adc_start pulse after first start, got %0d", adc_start_count);
+        end
+
+        $display("[%0t] TEST 3 start pulses passed", $time);
+
+        // release busy by finish pulse from ADC domain
+        $display("[%0t] Sending finish pulse", $time);
+        pulse_finish();
+
+        // a bit of wait for finish CDC back to ETH
+        repeat (20) @(posedge eth_clk_in);
+
+        // sanity check that commands are accepted again after finish
+        $display("[%0t] TEST 4: soft_reset after finish", $time);
+        send_cmd(8'h0F);
+
+        wait_dac_rst_count(2);
+        wait_adc_rst_count(2);
+
+        if (dac_rst_count != 2) begin
+            $fatal(1, "Expected exactly two dac_rst pulses total, got %0d", dac_rst_count);
+        end
+        if (adc_rst_count != 2) begin
+            $fatal(1, "Expected exactly two adc_rst pulses total, got %0d", adc_rst_count);
+        end
+
+        $display("[%0t] TEST 4 passed", $time);
+
+        $display("==============================================");
+        $display("ALL BASIC TESTS PASSED");
+        $display("dac_rst_count   = %0d", dac_rst_count);
+        $display("adc_rst_count   = %0d", adc_rst_count);
+        $display("dac_start_count = %0d", dac_start_count);
+        $display("adc_start_count = %0d", adc_start_count);
+        $display("==============================================");
+
+        #100;
+        $finish;
+    end
+
+endmodule

rtl/controller/tests/test_timing.xdc

@@ -0,0 +1,13 @@
+# Primary clocks
+create_clock -name eth_clk -period 8.000  [get_ports eth_clk_in]
+create_clock -name dac_clk -period 7.692  [get_ports dac_clk_in]
+create_clock -name adc_clk -period 15.385 [get_ports adc_clk_in]
+
+
+# Asynchronous clock groups
+# eth, dac, adc are independent domains
+
+set_clock_groups -name ASYNC_ETH_DAC_ADC -asynchronous \
+    -group [get_clocks eth_clk] \
+    -group [get_clocks dac_clk] \
+    -group [get_clocks adc_clk]

rtl/ethernet-udp/README.md

@@ -0,0 +1,54 @@
+# Ethernet UDP Stack
+
+Полный стек для Ethernet. Имеется поддержка ARP, ICMP (ping), и UDP. 
+- Рассчитан на скорость 1 ГБит/с
+- IP адреса устанавливаются заранее в axis_mac.sv
+- ARP и ICMP работают автоматически после инициализации модуля
+- Получаемые пейлоады по UDP выводятся через AXIS Master, когда получатель будет ready
+- Для отправки пейлоада по UDP используется сигнал-импульс send_req, который можно подать, когда модуль req_ready, после этого по готовности AXIS Slave можно начинать передавать данные пакета. Отправка следующего пакета будет доступна, когда данные предыдущего начнут отправляться (тоже сигнал req_ready).
+- Для прием имеется небольшая память на 2Кб. Пакет сначала помещается в нее и может быть отправлен по AXIS как только получатель готов. Если получатель не успевает принять полученный UDP пакет, то он может быть перезатерт новым.
+- Для отправки есть FIFO глубиной 2Кб. После запроса на отправку (send_req), при наполнении этого FIFO считается checksum пакета. Когда все data_length байт записаны - начинается отправка пакетов. Когда первые байты ушли - можно начинать передачу байт следующего пакета.
+## Структура src
+```
+├── eth - исходный код ethernet модуля
+│   ├── arbi - арбитер RGMII <-> GMII
+│   │   ├── gmii_arbi.v
+│   │   ├── gmii_rx_buffer.v
+│   │   └── gmii_tx_buffer.v
+│   ├── axis_mac.sv - обертка для AXIS
+│   ├── mac - основные файлы MAC части
+│   │   ├── arp_cache.v
+│   │   ├── crc.v
+│   │   ├── icmp_reply.v
+│   │   ├── mac_test.v
+│   │   ├── mac_top.v
+│   │   ├── rx - прием
+│   │   │   ├── arp_rx.v
+│   │   │   ├── ip_rx.v
+│   │   │   ├── mac_rx_top.v
+│   │   │   ├── mac_rx.v
+│   │   │   └── udp_rx.v
+│   │   └── tx - отправка
+│   │       ├── arp_tx.v
+│   │       ├── ip_tx_mode.v
+│   │       ├── ip_tx.v
+│   │       ├── mac_tx_mode.v
+│   │       ├── mac_tx_top.v
+│   │       ├── mac_tx.v
+│   │       └── udp_tx.v
+│   ├── reset.v
+│   └── util_gmii_to_rgmii.v
+└── ip: XCI файлы ip блоков 
+```
+
+## Тесты
+В tests есть Testbench, эмулирующий прием и отправку пакетов (test_axis_mac_rx.sv), а также имеются следующие тестовые проекты для отладки на ПЛИС AX7A035B:
+- Симуляция запускается в eth_axis через ```make sim```
+- eth_minimal - минимальный проект для теста PHY части. По умолчанию просто отправляет UDP пакет с фиксированным содержимым Hello ALINX на заданный IP. Если отправить UDP - то начнется трансляция пейлоада из принятого пакета.
+- eth_axis - проект с axis_mac и своеобразным echo-loopback. Начинает с ARP запроса, если получает ответ - то готов к работе. Можно отправлять UDP и получать эхо в ответ.
+
+## Сборка
+- Для сборки используется make
+- Собрать все вплоть до битстрима: ```make all```
+- Создать (если нету) и открыть вивадовский проект: ```make vivado```
+- По умолчанию в проектах используются IP 192.168.0.2 для платы и 192.168.0.3 для хоста, порт 8080 и на отправку, и на получение

rtl/ethernet-udp/src/eth/axis_mac.sv

@@ -1,3 +1,5 @@
+// ethernet MAC with axi stream IO with UDP
+
 `timescale 1 ns / 1 ns
 
 module axis_mac
@@ -14,8 +16,19 @@ module axis_mac
     // AXI-stream RX output (clock domain = gmii_rx_clk)
     (* MARK_DEBUG="true" *)output reg  [7:0]    m_axis_rx_tdata,
     (* MARK_DEBUG="true" *)output reg           m_axis_rx_tvalid,
-    input  wire          m_axis_rx_tready,
-    (* MARK_DEBUG="true" *)output reg           m_axis_rx_tlast
+    (* MARK_DEBUG="true" *)input  wire          m_axis_rx_tready,
+    (* MARK_DEBUG="true" *)output reg           m_axis_rx_tlast,
+    (* MARK_DEBUG="true" *)output wire [15:0]   udp_rec_data_length,
+
+    // tx part
+    (* MARK_DEBUG="true" *)input  wire        send_req,
+    input  wire [15:0] data_length,
+    (* MARK_DEBUG="true" *)output reg         req_ready,
+
+    (* MARK_DEBUG="true" *)input  wire [7:0]  s_axis_tx_tdata,
+    (* MARK_DEBUG="true" *)input  wire        s_axis_tx_tvalid,
+    (* MARK_DEBUG="true" *)output reg         s_axis_tx_tready,
+    (* MARK_DEBUG="true" *)input  wire        s_axis_tx_tlast
 );
 
     // ----------------------------------------------------------------
@@ -50,28 +63,26 @@ module axis_mac
         end
     end
 
-    // ----------------------------------------------------------------
-    // Unused user TX path into mac_top
-    // We disable user UDP TX for now.
-    // ARP replies and ICMP replies inside mac_top still work.
-    // ----------------------------------------------------------------
+    // TX signals
+    reg  [7:0]  tx_ram_wr_data;
+    reg         tx_ram_wr_en;
+    reg  [15:0] udp_send_data_length;
+    reg         udp_tx_req;
+    reg         arp_request_req;
+    wire        mac_send_end;
+
     wire        udp_ram_data_req;
     wire        udp_tx_end;
     wire        almost_full;
-    wire       mac_send_end;
-    wire       arp_found;
+    (* MARK_DEBUG="true" *)wire        arp_found;
     wire        mac_not_exist;
+    wire [15:0] udp_ram_data_count;
 
-    wire [7:0]  udp_rec_ram_rdata;
+    // RX signals
     reg  [10:0] udp_rec_ram_read_addr;
-    wire [15:0] udp_rec_data_length;
-    wire        udp_rec_data_valid;
+    wire [7:0]  udp_rec_ram_rdata;
     
-    wire [7:0]  tx_ram_wr_data      = 8'd0;
-    wire        tx_ram_wr_en        = 1'b0;
-    wire [15:0] udp_send_data_length = 16'd0;
-    wire        udp_tx_req          = 1'b0;
-    wire        arp_request_req     = 1'b0;
+    wire        udp_rec_data_valid;
 
     mac_top mac_top0 (
         .gmii_tx_clk               (gmii_tx_clk),
@@ -81,7 +92,7 @@ module axis_mac
         .source_mac_addr           (48'h00_0a_35_01_fe_c0),
         .TTL                       (8'h80),
         .source_ip_addr            (32'hc0a80002),   // 192.168.0.2
-        .destination_ip_addr       (32'hc0a80003),   // 192.168.0.3 (не используется для user TX пока)
+        .destination_ip_addr       (32'hc0a80003),   // 192.168.0.3
         .udp_send_source_port      (16'h1f90),       // 8080
         .udp_send_destination_port (16'h1f90),       // 8080
 
@@ -111,9 +122,7 @@ module axis_mac
         .mac_not_exist             (mac_not_exist)
     );
 
-    // ----------------------------------------------------------------
     // Detect "new packet ready" on udp_rec_data_valid rising edge
-    // ----------------------------------------------------------------
     reg udp_rec_data_valid_d0;
 
     always @(posedge gmii_rx_clk or negedge rst_n) begin
@@ -137,8 +146,6 @@ module axis_mac
     // - read bytes 0 .. payload_len-1 from RX RAM
     // - output them on AXIS
     //
-    // Because the BRAM read port is synchronous, this bridge may insert
-    // bubbles between bytes. For first bring-up this is fine.
     // ----------------------------------------------------------------
     localparam RX_IDLE  = 2'd0;
     localparam RX_NOTREADY  = 2'd1;
@@ -230,7 +237,6 @@ module axis_mac
                             rx_state <= RX_IDLE;
                         end
 
-
                         rx_index <= rx_index + 1'b1;
                         udp_rec_ram_read_addr <= rx_index + 1'b1; // next byte
                     end
@@ -245,4 +251,185 @@ module axis_mac
         end
     end
 
+    // ----------------------------------------------------------------
+    // TX FSM
+    // Semantics:
+    //   - send_req/data_length form a packet send request
+    //   - udp_tx_req is held HIGH until udp_ram_data_req pulses
+    //   - udp_ram_data_req is a pulse - start feeding payload now to RAM
+    //   - AXIS ready is asserted only during payload write phase
+    // ----------------------------------------------------------------
+    
+    
+    localparam TX_IDLE         = 3'd0;
+    localparam TX_ARP_REQ      = 3'd1;
+    localparam TX_ARP_SEND     = 3'd2;
+    localparam TX_WAIT_ARP     = 3'd3;
+    localparam TX_WAIT_RAM_REQ = 3'd4;
+    localparam TX_STREAM       = 3'd5;
+    localparam TX_WAIT_DRAIN   = 3'd6;
+
+    (* MARK_DEBUG="true" *)reg [2:0]  tx_state;
+    
+    assign arp_request_req  = (tx_state == TX_ARP_REQ) ;
+
+    reg [15:0] tx_req_len;
+    reg [15:0] tx_bytes_written;
+    reg [15:0] tx_release_threshold;
+
+    reg        tx_req_inflight;
+    
+    // register for long arp timeout, if no got no response
+    reg [31:0] arp_delay;
+    reg arp_cached;
+
+    always @(posedge gmii_tx_clk or negedge rst_n) begin
+        if (!rst_n) begin
+            tx_state             <= TX_IDLE;
+
+            tx_ram_wr_data       <= 8'd0;
+            arp_cached           <= 1'b0;
+            tx_ram_wr_en         <= 1'b0;
+            udp_send_data_length <= 16'd0;
+            udp_tx_req           <= 1'b0;
+            arp_delay            <= 32'b0;
+
+            s_axis_tx_tready     <= 1'b0;
+            req_ready            <= 1'b0;
+
+            tx_req_len           <= 16'd0;
+            tx_bytes_written     <= 16'd0;
+            tx_release_threshold <= 16'd0;
+
+            tx_req_inflight      <= 1'b0;
+        end else begin
+            // defaults
+            tx_ram_wr_en    <= 1'b0;
+
+            case (tx_state)
+                // Ready to accept a new packet request
+                TX_IDLE: begin
+                    udp_tx_req       <= 1'b0;
+                    s_axis_tx_tready <= 1'b0;
+                    tx_bytes_written <= 16'd0;
+                    tx_req_inflight  <= 1'b0;
+
+                    req_ready <= arp_cached && !almost_full;
+
+                    if (send_req && req_ready) begin
+                        tx_req_len           <= data_length;
+                        udp_send_data_length <= data_length;
+                        tx_req_inflight      <= 1'b1;
+
+                        // threshold for allowing next packet
+                        // to be written to the RAM
+                        if (data_length > 16'd16)
+                            tx_release_threshold <= data_length - 16'd16;
+                        else
+                            tx_release_threshold <= 16'd0;
+
+                            tx_state <= TX_WAIT_RAM_REQ;
+                    end
+                    
+                    // arp check
+                    if (!arp_cached) begin
+                        tx_state <= TX_ARP_REQ;
+                    end
+                end
+
+                // Pulse ARP request
+                TX_ARP_REQ: begin
+                    req_ready        <= 1'b0;
+                    s_axis_tx_tready <= 1'b0;
+                    udp_tx_req       <= 1'b0;
+                    
+                    arp_delay        <= 32'ha000000;
+                    tx_state         <= TX_ARP_SEND;
+                end
+
+                // Wait until ARP is resolved
+                TX_ARP_SEND: begin
+                    req_ready        <= 1'b0;
+                    s_axis_tx_tready <= 1'b0;
+                    udp_tx_req       <= 1'b0;
+
+                    // sent
+                    if (mac_send_end)
+                        tx_state <= TX_WAIT_ARP;
+                end
+                
+                // wait for ARP response
+                TX_WAIT_ARP: begin
+                    if (arp_found) begin
+                        arp_cached <= 1'b1;
+                        tx_state <= TX_IDLE;
+                    end
+                    
+                    // timeout to not spam ARPs
+                    if (arp_delay == 32'b0) begin
+                        // re-try
+                        tx_state <= TX_ARP_REQ;
+                    end else begin
+                        // wait
+                        arp_delay = arp_delay - 32'b1;
+                    end 
+                    
+                end
+
+                // Hold udp_tx_req until udp_ram_data_req pulse arrives
+                TX_WAIT_RAM_REQ: begin
+                    req_ready        <= 1'b0;
+                    udp_tx_req       <= 1'b1;
+
+                    if (udp_ram_data_req) begin
+                        udp_tx_req       <= 1'b0;
+                        s_axis_tx_tready <= 1'b1;
+                        tx_state         <= TX_STREAM;
+                    end
+                end
+
+                // Accept AXIS bytes and write them into TX RAM
+                TX_STREAM: begin
+                    req_ready  <= 1'b0;
+                    udp_tx_req <= 1'b0;
+
+                    // keep ready high while receiving payload bytes
+                    s_axis_tx_tready <= (tx_bytes_written < tx_req_len);
+
+                    if (s_axis_tx_tvalid && s_axis_tx_tready) begin
+                        tx_ram_wr_data <= s_axis_tx_tdata;
+                        tx_ram_wr_en   <= 1'b1;
+
+                        tx_bytes_written <= tx_bytes_written + 1'b1;
+
+                        if (tx_bytes_written + 1'b1 >= tx_req_len) begin
+                            s_axis_tx_tready <= 1'b0;
+                            tx_state         <= TX_WAIT_DRAIN;
+                        end
+                    end
+                end
+
+                // Packet payload is already in RAM.
+                // Wait until TX RAM starts draining enough to allow
+                // the next request.
+                TX_WAIT_DRAIN: begin
+                    s_axis_tx_tready <= 1'b0;
+                    udp_tx_req       <= 1'b0;
+
+                    if (udp_ram_data_count <= tx_release_threshold)
+                        tx_state <= TX_IDLE;
+
+                end
+
+                default: begin
+                    tx_state         <= TX_IDLE;
+                    tx_ram_wr_en     <= 1'b0;
+                    udp_tx_req       <= 1'b0;
+                    s_axis_tx_tready <= 1'b0;
+                    req_ready        <= 1'b0;
+                end
+            endcase
+        end
+    end
+
 endmodule

rtl/ethernet-udp/src/eth/mac/mac_test.v

@@ -4,7 +4,7 @@
 //Description :
 //
 //////////////////////////////////////////////////////////////////////////////////////
-//`define TEST_SPEED
+`define TEST_SPEED
 `timescale 1 ns/1 ns
 module mac_test
 (
@@ -74,7 +74,7 @@ parameter WAIT          = 9'b010_000_000 ;
 parameter CHECK_ARP     = 9'b100_000_000 ;
 
 
-reg [8:0]    state  ;
+(* MARK_DEBUG="true" *)  reg [8:0]    state  ;
 reg [8:0]    next_state ;
 reg  [15:0]  ram_cnt ;
 reg    almost_full_d0 ;
@@ -278,7 +278,7 @@ always@(posedge gmii_rx_clk or negedge rst_n)
 		udp_send_data_length <= udp_rec_data_length - 8  ;
 	 else
 	 `ifdef TEST_SPEED 
-       udp_send_data_length <= 16'd1000 ;	 
+       udp_send_data_length <= 16'd100 ;	 
 	 `else	 
 	   udp_send_data_length <= 4*UDP_DEPTH ;
 	 `endif

rtl/ethernet-udp/src/eth/mac/mac_top.v

@@ -1,8 +1,6 @@
-//////////////////////////////////////////////////////////////////////////////////////
-//Module Name : mac_top
-//Description :
-//
-//////////////////////////////////////////////////////////////////////////////////////
+// Top module for base ethernet operations
+// inheireted from Alinx
+
 `timescale 1 ns/1 ns
 module mac_top
        (
@@ -37,6 +35,7 @@ module mac_top
          input  [10:0]        udp_rec_ram_read_addr,
          output [15:0]        udp_rec_data_length,
          output               udp_rec_data_valid,
+         output [11:0]        udp_ram_data_count,
          
          output               arp_found,
          output               mac_not_exist
@@ -81,6 +80,7 @@ mac_tx_top mac_tx0
             .arp_rec_source_ip_addr      (arp_rec_source_ip_addr ),
             .arp_rec_source_mac_addr     (arp_rec_source_mac_addr ),
             .arp_request_req             (arp_request_req ),
+            .udp_ram_data_count          (udp_ram_data_count ),
             
             
             .ram_wr_data                 (ram_wr_data) ,

rtl/ethernet-udp/src/eth/mac/tx/mac_tx_top.v

@@ -31,8 +31,9 @@ module mac_tx_top
          (* MARK_DEBUG="true" *)input  [15:0]        udp_send_data_length,
          (* MARK_DEBUG="true" *)output               udp_tx_end,
          (* MARK_DEBUG="true" *)output               almost_full,
+         (* MARK_DEBUG="true" *)output [11:0]        udp_ram_data_count,
          
-         output               upper_data_req,
+         (* MARK_DEBUG="true" *)output               upper_data_req,
          input                icmp_tx_ready,
          input  [7:0]         icmp_tx_data,
          input                icmp_tx_end,
@@ -251,7 +252,8 @@ udp_tx udp0
          .udp_tx_ready                   (udp_tx_ready               ),
          .udp_tx_data                    (udp_tx_data                ),
          .udp_tx_end                     (udp_tx_end                 ),
-         .almost_full                    (almost_full                )        
+         .almost_full                    (almost_full                ),
+         .udp_ram_data_count             (udp_ram_data_count         )       
        ) ;
        
 endmodule

rtl/ethernet-udp/src/eth/mac/tx/udp_tx.v

@@ -27,13 +27,14 @@ module udp_tx
           output reg               udp_tx_ready,
           output reg [7:0]         udp_tx_data,
           output reg               udp_tx_end,
-          output                   almost_full
+          output                   almost_full,
+          output     [11:0]        udp_ram_data_count
          
        ) ;
        
 
 reg                       ram_rd_en ;
-wire [3:0]                usedw     ;
+(* MARK_DEBUG="true" *) wire [3:0]                usedw     ;
 reg  [3:0]                fifo_count ;
 
 reg  [7:0]                ram_rdata_d0  ;
@@ -62,7 +63,7 @@ parameter UDP_SEND          = 6'b010000 ;
 parameter UDP_END           = 6'b100000 ;
 
 
-reg [5:0]    state  ;
+(* MARK_DEBUG="true" *) reg [5:0]    state  ;
 reg [5:0]    next_state ;
 
 
@@ -222,7 +223,7 @@ udp_tx_data_fifo tx_data_fifo
     .full         (               ),                // output wire full
     .almost_full  (almost_full    ),  // output wire almost_full
     .empty        (               ),              // output wire empty
-    .data_count   (               )    // output wire [11 : 0] data_count
+    .data_count   (udp_ram_data_count )    // output wire [11 : 0] data_count
   );
 
 
@@ -356,7 +357,7 @@ udp_tx_data_fifo tx_data_fifo
   localparam GEN_CHECKSUM_END  = 6'b010000 ;
   localparam CHECKSUM_WAIT     = 6'b100000 ;
   
-  reg [5:0]    ck_state  ;
+  (* MARK_DEBUG="true" *) reg [5:0]    ck_state  ;
   reg [5:0]    ck_next_state ;
   
   always @(posedge clk or negedge rst_n)

rtl/ethernet-udp/src/eth/util_gmii_to_rgmii.v

@@ -180,7 +180,7 @@ module util_gmii_to_rgmii (
          .DELAY_SRC("IDATAIN"),           // Delay input (IDATAIN, DATAIN)
          .HIGH_PERFORMANCE_MODE("FALSE"), // Reduced jitter ("TRUE"), Reduced power ("FALSE")
          .IDELAY_TYPE("FIXED"),           // FIXED, VARIABLE, VAR_LOAD, VAR_LOAD_PIPE
-         .IDELAY_VALUE(16),                // Input delay tap setting (0-31)
+         .IDELAY_VALUE(16),                // Input delay tap setting (0-31) May be changed for more stability
          .PIPE_SEL("FALSE"),              // Select pipelined mode, FALSE, TRUE
          .REFCLK_FREQUENCY(200.0),        // IDELAYCTRL clock input frequency in MHz (190.0-210.0, 290.0-310.0).
          .SIGNAL_PATTERN("DATA")          // DATA, CLOCK input signal

rtl/ethernet-udp/tests/eth_axis/Makefile

@@ -8,13 +8,13 @@
 
 # FPGA settings
 FPGA_PART = xc7a35tfgg484-1
-FPGA_TOP = ethernet_test_minimal
+FPGA_TOP = ethernet_axis_echo
 FPGA_ARCH = artix7
 
 RTL_DIR = ../../src
 
 # Files for synthesis
-SYN_FILES = ethernet_test_minimal.v
+SYN_FILES = ethernet_axis_echo.v
 
 include ../../../../scripts/vivado.mk
 
@@ -22,6 +22,12 @@ SYN_FILES += $(sort $(shell find ../../src -type f \( -name '*.v' -o -name '*.sv
 
 XCI_FILES = $(sort $(shell find ../../src -type f -name '*.xci'))
 
+XDC_FILES += debug.xdc
+XDC_FILES += ../../../../constraints/ax7a035b.xdc
+
+SIM_TOP = tb_mac_test
+TB_FILES = test_axis_mac_rx.sv
+
 program: $(PROJECT).bit
 	echo "open_hw_manager" > program.tcl
 	echo "connect_hw_server" >> program.tcl

rtl/ethernet-udp/tests/eth_axis/debug.xdc

@@ -0,0 +1,260 @@
+# debug ila
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 8 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {arbi_inst/rx_buffer_inst/e10_100_rxd[0]} {arbi_inst/rx_buffer_inst/e10_100_rxd[1]} {arbi_inst/rx_buffer_inst/e10_100_rxd[2]} {arbi_inst/rx_buffer_inst/e10_100_rxd[3]} {arbi_inst/rx_buffer_inst/e10_100_rxd[4]} {arbi_inst/rx_buffer_inst/e10_100_rxd[5]} {arbi_inst/rx_buffer_inst/e10_100_rxd[6]} {arbi_inst/rx_buffer_inst/e10_100_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 8 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {arbi_inst/gmii_rxd[0]} {arbi_inst/gmii_rxd[1]} {arbi_inst/gmii_rxd[2]} {arbi_inst/gmii_rxd[3]} {arbi_inst/gmii_rxd[4]} {arbi_inst/gmii_rxd[5]} {arbi_inst/gmii_rxd[6]} {arbi_inst/gmii_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 8 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {arbi_inst/gmii_txd[0]} {arbi_inst/gmii_txd[1]} {arbi_inst/gmii_txd[2]} {arbi_inst/gmii_txd[3]} {arbi_inst/gmii_txd[4]} {arbi_inst/gmii_txd[5]} {arbi_inst/gmii_txd[6]} {arbi_inst/gmii_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 8 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list {arbi_inst/e_txd[0]} {arbi_inst/e_txd[1]} {arbi_inst/e_txd[2]} {arbi_inst/e_txd[3]} {arbi_inst/e_txd[4]} {arbi_inst/e_txd[5]} {arbi_inst/e_txd[6]} {arbi_inst/e_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 8 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list {arbi_inst/e_rxd[0]} {arbi_inst/e_rxd[1]} {arbi_inst/e_rxd[2]} {arbi_inst/e_rxd[3]} {arbi_inst/e_rxd[4]} {arbi_inst/e_rxd[5]} {arbi_inst/e_rxd[6]} {arbi_inst/e_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 16 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list {arbi_inst/tx_buffer_inst/tx_data_cnt[0]} {arbi_inst/tx_buffer_inst/tx_data_cnt[1]} {arbi_inst/tx_buffer_inst/tx_data_cnt[2]} {arbi_inst/tx_buffer_inst/tx_data_cnt[3]} {arbi_inst/tx_buffer_inst/tx_data_cnt[4]} {arbi_inst/tx_buffer_inst/tx_data_cnt[5]} {arbi_inst/tx_buffer_inst/tx_data_cnt[6]} {arbi_inst/tx_buffer_inst/tx_data_cnt[7]} {arbi_inst/tx_buffer_inst/tx_data_cnt[8]} {arbi_inst/tx_buffer_inst/tx_data_cnt[9]} {arbi_inst/tx_buffer_inst/tx_data_cnt[10]} {arbi_inst/tx_buffer_inst/tx_data_cnt[11]} {arbi_inst/tx_buffer_inst/tx_data_cnt[12]} {arbi_inst/tx_buffer_inst/tx_data_cnt[13]} {arbi_inst/tx_buffer_inst/tx_data_cnt[14]} {arbi_inst/tx_buffer_inst/tx_data_cnt[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 8 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list {arbi_inst/tx_buffer_inst/tx_rdata[0]} {arbi_inst/tx_buffer_inst/tx_rdata[1]} {arbi_inst/tx_buffer_inst/tx_rdata[2]} {arbi_inst/tx_buffer_inst/tx_rdata[3]} {arbi_inst/tx_buffer_inst/tx_rdata[4]} {arbi_inst/tx_buffer_inst/tx_rdata[5]} {arbi_inst/tx_buffer_inst/tx_rdata[6]} {arbi_inst/tx_buffer_inst/tx_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe7]
+set_property port_width 8 [get_debug_ports u_ila_0/probe7]
+connect_debug_port u_ila_0/probe7 [get_nets [list {arbi_inst/tx_buffer_inst/tx_wdata[0]} {arbi_inst/tx_buffer_inst/tx_wdata[1]} {arbi_inst/tx_buffer_inst/tx_wdata[2]} {arbi_inst/tx_buffer_inst/tx_wdata[3]} {arbi_inst/tx_buffer_inst/tx_wdata[4]} {arbi_inst/tx_buffer_inst/tx_wdata[5]} {arbi_inst/tx_buffer_inst/tx_wdata[6]} {arbi_inst/tx_buffer_inst/tx_wdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe8]
+set_property port_width 6 [get_debug_ports u_ila_0/probe8]
+connect_debug_port u_ila_0/probe8 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[0]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[1]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[2]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[3]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[4]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe9]
+set_property port_width 16 [get_debug_ports u_ila_0/probe9]
+connect_debug_port u_ila_0/probe9 [get_nets [list {axis_mac0/udp_rec_data_length[0]} {axis_mac0/udp_rec_data_length[1]} {axis_mac0/udp_rec_data_length[2]} {axis_mac0/udp_rec_data_length[3]} {axis_mac0/udp_rec_data_length[4]} {axis_mac0/udp_rec_data_length[5]} {axis_mac0/udp_rec_data_length[6]} {axis_mac0/udp_rec_data_length[7]} {axis_mac0/udp_rec_data_length[8]} {axis_mac0/udp_rec_data_length[9]} {axis_mac0/udp_rec_data_length[10]} {axis_mac0/udp_rec_data_length[11]} {axis_mac0/udp_rec_data_length[12]} {axis_mac0/udp_rec_data_length[13]} {axis_mac0/udp_rec_data_length[14]} {axis_mac0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe10]
+set_property port_width 3 [get_debug_ports u_ila_0/probe10]
+connect_debug_port u_ila_0/probe10 [get_nets [list {axis_mac0/tx_state[0]} {axis_mac0/tx_state[1]} {axis_mac0/tx_state[2]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe11]
+set_property port_width 8 [get_debug_ports u_ila_0/probe11]
+connect_debug_port u_ila_0/probe11 [get_nets [list {axis_mac0/s_axis_tx_tdata[0]} {axis_mac0/s_axis_tx_tdata[1]} {axis_mac0/s_axis_tx_tdata[2]} {axis_mac0/s_axis_tx_tdata[3]} {axis_mac0/s_axis_tx_tdata[4]} {axis_mac0/s_axis_tx_tdata[5]} {axis_mac0/s_axis_tx_tdata[6]} {axis_mac0/s_axis_tx_tdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe12]
+set_property port_width 2 [get_debug_ports u_ila_0/probe12]
+connect_debug_port u_ila_0/probe12 [get_nets [list {axis_mac0/rx_state[0]} {axis_mac0/rx_state[1]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe13]
+set_property port_width 16 [get_debug_ports u_ila_0/probe13]
+connect_debug_port u_ila_0/probe13 [get_nets [list {axis_mac0/rx_payload_len[0]} {axis_mac0/rx_payload_len[1]} {axis_mac0/rx_payload_len[2]} {axis_mac0/rx_payload_len[3]} {axis_mac0/rx_payload_len[4]} {axis_mac0/rx_payload_len[5]} {axis_mac0/rx_payload_len[6]} {axis_mac0/rx_payload_len[7]} {axis_mac0/rx_payload_len[8]} {axis_mac0/rx_payload_len[9]} {axis_mac0/rx_payload_len[10]} {axis_mac0/rx_payload_len[11]} {axis_mac0/rx_payload_len[12]} {axis_mac0/rx_payload_len[13]} {axis_mac0/rx_payload_len[14]} {axis_mac0/rx_payload_len[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe14]
+set_property port_width 16 [get_debug_ports u_ila_0/probe14]
+connect_debug_port u_ila_0/probe14 [get_nets [list {axis_mac0/rx_index[0]} {axis_mac0/rx_index[1]} {axis_mac0/rx_index[2]} {axis_mac0/rx_index[3]} {axis_mac0/rx_index[4]} {axis_mac0/rx_index[5]} {axis_mac0/rx_index[6]} {axis_mac0/rx_index[7]} {axis_mac0/rx_index[8]} {axis_mac0/rx_index[9]} {axis_mac0/rx_index[10]} {axis_mac0/rx_index[11]} {axis_mac0/rx_index[12]} {axis_mac0/rx_index[13]} {axis_mac0/rx_index[14]} {axis_mac0/rx_index[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe15]
+set_property port_width 8 [get_debug_ports u_ila_0/probe15]
+connect_debug_port u_ila_0/probe15 [get_nets [list {axis_mac0/m_axis_rx_tdata[0]} {axis_mac0/m_axis_rx_tdata[1]} {axis_mac0/m_axis_rx_tdata[2]} {axis_mac0/m_axis_rx_tdata[3]} {axis_mac0/m_axis_rx_tdata[4]} {axis_mac0/m_axis_rx_tdata[5]} {axis_mac0/m_axis_rx_tdata[6]} {axis_mac0/m_axis_rx_tdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe16]
+set_property port_width 16 [get_debug_ports u_ila_0/probe16]
+connect_debug_port u_ila_0/probe16 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[0]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[1]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[2]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[3]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[4]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[5]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[6]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[7]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[8]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[9]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[10]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[11]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[12]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[13]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[14]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe17]
+set_property port_width 12 [get_debug_ports u_ila_0/probe17]
+connect_debug_port u_ila_0/probe17 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[0]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[1]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[2]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[3]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[4]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[5]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[6]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[7]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[8]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[9]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[10]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[11]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe18]
+set_property port_width 8 [get_debug_ports u_ila_0/probe18]
+connect_debug_port u_ila_0/probe18 [get_nets [list {axis_mac0/mac_top0/mac_tx0/ram_wr_data[0]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[1]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[2]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[3]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[4]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[5]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[6]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe19]
+set_property port_width 8 [get_debug_ports u_ila_0/probe19]
+connect_debug_port u_ila_0/probe19 [get_nets [list {axis_mac0/mac_top0/mac_tx0/mac_tx_data[0]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[1]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[2]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[3]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[4]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[5]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[6]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe20]
+set_property port_width 4 [get_debug_ports u_ila_0/probe20]
+connect_debug_port u_ila_0/probe20 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/usedw[0]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[1]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[2]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[3]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe21]
+set_property port_width 6 [get_debug_ports u_ila_0/probe21]
+connect_debug_port u_ila_0/probe21 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/state[0]} {axis_mac0/mac_top0/mac_tx0/udp0/state[1]} {axis_mac0/mac_top0/mac_tx0/udp0/state[2]} {axis_mac0/mac_top0/mac_tx0/udp0/state[3]} {axis_mac0/mac_top0/mac_tx0/udp0/state[4]} {axis_mac0/mac_top0/mac_tx0/udp0/state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe22]
+set_property port_width 16 [get_debug_ports u_ila_0/probe22]
+connect_debug_port u_ila_0/probe22 [get_nets [list {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[0]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[1]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[2]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[3]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[4]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[5]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[6]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[7]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[8]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[9]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[10]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[11]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[12]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[13]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[14]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe23]
+set_property port_width 11 [get_debug_ports u_ila_0/probe23]
+connect_debug_port u_ila_0/probe23 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[7]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[8]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[9]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe24]
+set_property port_width 8 [get_debug_ports u_ila_0/probe24]
+connect_debug_port u_ila_0/probe24 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe25]
+set_property port_width 16 [get_debug_ports u_ila_0/probe25]
+connect_debug_port u_ila_0/probe25 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[7]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[8]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[9]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[10]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[11]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[12]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[13]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[14]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe26]
+set_property port_width 8 [get_debug_ports u_ila_0/probe26]
+connect_debug_port u_ila_0/probe26 [get_nets [list {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[0]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[1]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[2]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[3]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[4]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[5]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[6]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe27]
+set_property port_width 16 [get_debug_ports u_ila_0/probe27]
+connect_debug_port u_ila_0/probe27 [get_nets [list {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[0]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[1]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[2]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[3]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[4]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[5]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[6]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[7]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[8]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[9]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[10]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[11]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[12]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[13]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[14]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe28]
+set_property port_width 8 [get_debug_ports u_ila_0/probe28]
+connect_debug_port u_ila_0/probe28 [get_nets [list {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[0]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[1]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[2]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[3]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[4]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[5]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[6]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe29]
+set_property port_width 11 [get_debug_ports u_ila_0/probe29]
+connect_debug_port u_ila_0/probe29 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[0]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[1]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[2]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[3]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[4]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[5]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[6]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[7]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[8]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[9]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe30]
+set_property port_width 2 [get_debug_ports u_ila_0/probe30]
+connect_debug_port u_ila_0/probe30 [get_nets [list {test_state[0]} {test_state[1]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe31]
+set_property port_width 1 [get_debug_ports u_ila_0/probe31]
+connect_debug_port u_ila_0/probe31 [get_nets [list axis_mac0/mac_top0/mac_tx0/almost_full]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe32]
+set_property port_width 1 [get_debug_ports u_ila_0/probe32]
+connect_debug_port u_ila_0/probe32 [get_nets [list axis_mac0/arp_found]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe33]
+set_property port_width 1 [get_debug_ports u_ila_0/probe33]
+connect_debug_port u_ila_0/probe33 [get_nets [list arbi_inst/rx_buffer_inst/e10_100_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe34]
+set_property port_width 1 [get_debug_ports u_ila_0/probe34]
+connect_debug_port u_ila_0/probe34 [get_nets [list arbi_inst/e_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe35]
+set_property port_width 1 [get_debug_ports u_ila_0/probe35]
+connect_debug_port u_ila_0/probe35 [get_nets [list arbi_inst/e_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe36]
+set_property port_width 1 [get_debug_ports u_ila_0/probe36]
+connect_debug_port u_ila_0/probe36 [get_nets [list arbi_inst/gmii_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe37]
+set_property port_width 1 [get_debug_ports u_ila_0/probe37]
+connect_debug_port u_ila_0/probe37 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d0]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe38]
+set_property port_width 1 [get_debug_ports u_ila_0/probe38]
+connect_debug_port u_ila_0/probe38 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d1]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe39]
+set_property port_width 1 [get_debug_ports u_ila_0/probe39]
+connect_debug_port u_ila_0/probe39 [get_nets [list arbi_inst/gmii_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe40]
+set_property port_width 1 [get_debug_ports u_ila_0/probe40]
+connect_debug_port u_ila_0/probe40 [get_nets [list axis_mac0/m_axis_rx_tlast]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe41]
+set_property port_width 1 [get_debug_ports u_ila_0/probe41]
+connect_debug_port u_ila_0/probe41 [get_nets [list axis_mac0/m_axis_rx_tready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe42]
+set_property port_width 1 [get_debug_ports u_ila_0/probe42]
+connect_debug_port u_ila_0/probe42 [get_nets [list axis_mac0/m_axis_rx_tvalid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe43]
+set_property port_width 1 [get_debug_ports u_ila_0/probe43]
+connect_debug_port u_ila_0/probe43 [get_nets [list axis_mac0/mac_top0/mac_tx0/mac_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe44]
+set_property port_width 1 [get_debug_ports u_ila_0/probe44]
+connect_debug_port u_ila_0/probe44 [get_nets [list axis_mac0/mac_top0/mac_tx0/mac_send_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe45]
+set_property port_width 1 [get_debug_ports u_ila_0/probe45]
+connect_debug_port u_ila_0/probe45 [get_nets [list axis_mac0/mac_top0/mac_rx0/udp0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe46]
+set_property port_width 1 [get_debug_ports u_ila_0/probe46]
+connect_debug_port u_ila_0/probe46 [get_nets [list axis_mac0/mac_top0/mac_tx0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe47]
+set_property port_width 1 [get_debug_ports u_ila_0/probe47]
+connect_debug_port u_ila_0/probe47 [get_nets [list req_ready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe48]
+set_property port_width 1 [get_debug_ports u_ila_0/probe48]
+connect_debug_port u_ila_0/probe48 [get_nets [list axis_mac0/req_ready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe49]
+set_property port_width 1 [get_debug_ports u_ila_0/probe49]
+connect_debug_port u_ila_0/probe49 [get_nets [list axis_mac0/s_axis_tx_tlast]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe50]
+set_property port_width 1 [get_debug_ports u_ila_0/probe50]
+connect_debug_port u_ila_0/probe50 [get_nets [list axis_mac0/s_axis_tx_tready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe51]
+set_property port_width 1 [get_debug_ports u_ila_0/probe51]
+connect_debug_port u_ila_0/probe51 [get_nets [list axis_mac0/s_axis_tx_tvalid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe52]
+set_property port_width 1 [get_debug_ports u_ila_0/probe52]
+connect_debug_port u_ila_0/probe52 [get_nets [list axis_mac0/send_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe53]
+set_property port_width 1 [get_debug_ports u_ila_0/probe53]
+connect_debug_port u_ila_0/probe53 [get_nets [list send_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe54]
+set_property port_width 1 [get_debug_ports u_ila_0/probe54]
+connect_debug_port u_ila_0/probe54 [get_nets [list arbi_inst/tx_buffer_inst/tx_rden]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe55]
+set_property port_width 1 [get_debug_ports u_ila_0/probe55]
+connect_debug_port u_ila_0/probe55 [get_nets [list arbi_inst/tx_buffer_inst/tx_wren]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe56]
+set_property port_width 1 [get_debug_ports u_ila_0/probe56]
+connect_debug_port u_ila_0/probe56 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_ram_data_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe57]
+set_property port_width 1 [get_debug_ports u_ila_0/probe57]
+connect_debug_port u_ila_0/probe57 [get_nets [list axis_mac0/mac_top0/mac_rx0/udp_rec_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe58]
+set_property port_width 1 [get_debug_ports u_ila_0/probe58]
+connect_debug_port u_ila_0/probe58 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_tx_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe59]
+set_property port_width 1 [get_debug_ports u_ila_0/probe59]
+connect_debug_port u_ila_0/probe59 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_tx_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe60]
+set_property port_width 1 [get_debug_ports u_ila_0/probe60]
+connect_debug_port u_ila_0/probe60 [get_nets [list axis_mac0/mac_top0/mac_tx0/upper_data_req]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets rgmii_rxc_IBUF_BUFG]

rtl/ethernet-udp/tests/eth_axis/ethernet_axis_echo.v

@@ -0,0 +1,344 @@
+// project with UDP ethernet echo
+// use axi streams from axis_mac
+// fpga IP: 192.168.0.2
+// host IP: 192.168.0.3
+
+`timescale 1 ns / 1 ns
+
+module ethernet_axis_echo
+(
+    input               sys_clk_p,
+    input               sys_clk_n,
+    input               rst_n,
+    output [3:0]        led,
+    output              e_reset,
+    output              e_mdc,
+    inout               e_mdio,
+    output [3:0]        rgmii_txd,
+    output              rgmii_txctl,
+    output              rgmii_txc,
+    input  [3:0]        rgmii_rxd,
+    input               rgmii_rxctl,
+    input               rgmii_rxc
+);
+
+    // ------------------------------------------------------------
+    // Internal GMII-side signals
+    // ------------------------------------------------------------
+    wire  [7:0] gmii_txd;
+    wire        gmii_tx_en;
+    wire        gmii_tx_er;
+    wire        gmii_tx_clk;
+    wire        gmii_crs;
+    wire        gmii_col;
+    wire  [7:0] gmii_rxd_i;
+    wire        gmii_rx_dv;
+    wire        gmii_rx_er;
+    wire        gmii_rx_clk;
+
+    wire [31:0] pack_total_len;
+
+    wire        e_rx_dv;
+    wire [7:0]  e_rxd;
+    wire        e_tx_en;
+    wire [7:0]  e_txd;
+    wire        e_rst_n;
+    wire        sys_clk;
+
+    wire        duplex_mode;
+
+    assign duplex_mode = 1'b1;
+
+    // ------------------------------------------------------------
+    // System clock buffer
+    // ------------------------------------------------------------
+    IBUFDS sys_clk_ibufgds
+    (
+        .O  (sys_clk),
+        .I  (sys_clk_p),
+        .IB (sys_clk_n)
+    );
+
+    // ------------------------------------------------------------
+    // IDELAYCTRL
+    // ------------------------------------------------------------
+    (* IODELAY_GROUP = "rgmii_idelay_group" *)
+    IDELAYCTRL IDELAYCTRL_inst (
+        .RDY(),
+        .REFCLK(sys_clk),
+        .RST(1'b0)
+    );
+
+    // ------------------------------------------------------------
+    // GMII <-> RGMII conversion
+    // ------------------------------------------------------------
+    util_gmii_to_rgmii util_gmii_to_rgmii_m0
+    (
+        .reset           (1'b0),
+        .rgmii_td        (rgmii_txd),
+        .rgmii_tx_ctl    (rgmii_txctl),
+        .rgmii_txc       (rgmii_txc),
+        .rgmii_rd        (rgmii_rxd),
+        .rgmii_rx_ctl    (rgmii_rxctl),
+        .gmii_rx_clk     (gmii_rx_clk),
+        .gmii_txd        (e_txd),
+        .gmii_tx_en      (e_tx_en),
+        .gmii_tx_er      (1'b0),
+        .gmii_tx_clk     (gmii_tx_clk),
+        .gmii_crs        (gmii_crs),
+        .gmii_col        (gmii_col),
+        .gmii_rxd        (gmii_rxd_i),
+        .rgmii_rxc       (rgmii_rxc),
+        .gmii_rx_dv      (gmii_rx_dv),
+        .gmii_rx_er      (gmii_rx_er),
+        .speed_selection (2'b10),
+        .duplex_mode     (duplex_mode)
+    );
+
+    // ------------------------------------------------------------
+    // GMII arbitration / adaptation
+    // ------------------------------------------------------------
+    gmii_arbi arbi_inst
+    (
+        .clk            (gmii_tx_clk),
+        .rst_n          (rst_n),
+        .speed          (2'b10),
+        .link           (1'b1),
+        .pack_total_len (pack_total_len),
+        .e_rst_n        (e_rst_n),
+        .gmii_rx_dv     (gmii_rx_dv),
+        .gmii_rxd       (gmii_rxd_i),
+        .gmii_tx_en     (gmii_tx_en),
+        .gmii_txd       (gmii_txd),
+        .e_rx_dv        (e_rx_dv),
+        .e_rxd          (e_rxd),
+        .e_tx_en        (e_tx_en),
+        .e_txd          (e_txd)
+    );
+
+    // ------------------------------------------------------------
+    // axis_mac interface
+    // ------------------------------------------------------------
+    (* MARK_DEBUG="true" *)wire        req_ready;
+
+    (* MARK_DEBUG="true" *)reg         send_req;
+    reg  [15:0] data_length;
+
+    reg  [7:0]  s_axis_tx_tdata;
+    reg         s_axis_tx_tvalid;
+    wire        s_axis_tx_tready;
+    reg         s_axis_tx_tlast;
+
+    wire [7:0]  m_axis_rx_tdata;
+    wire        m_axis_rx_tvalid;
+    reg         m_axis_rx_tready;
+    wire        m_axis_rx_tlast;
+
+    // ------------------------------------------------------------
+    // axis_mac
+    // ------------------------------------------------------------
+    axis_mac axis_mac0
+    (
+        .gmii_tx_clk       (gmii_tx_clk),
+        .gmii_rx_clk       (gmii_rx_clk),
+        .rst_n             (e_rst_n),
+
+        .gmii_rx_dv        (e_rx_dv),
+        .gmii_rxd          (e_rxd),
+        .gmii_tx_en        (gmii_tx_en),
+        .gmii_txd          (gmii_txd),
+
+        .send_req          (send_req),
+        .data_length       (data_length),
+        .req_ready         (req_ready),
+
+        .s_axis_tx_tdata   (s_axis_tx_tdata),
+        .s_axis_tx_tvalid  (s_axis_tx_tvalid),
+        .s_axis_tx_tready  (s_axis_tx_tready),
+        .s_axis_tx_tlast   (s_axis_tx_tlast),
+
+        .m_axis_rx_tdata   (m_axis_rx_tdata),
+        .m_axis_rx_tvalid  (m_axis_rx_tvalid),
+        .m_axis_rx_tready  (m_axis_rx_tready),
+        .m_axis_rx_tlast   (m_axis_rx_tlast)
+    );
+
+    // LEDs
+    assign led[0] = req_ready;
+    assign led[1] = !m_axis_rx_tvalid;
+    assign led[2] = !s_axis_tx_tvalid;
+    assign led[3] = e_rst_n;
+
+    // Minimal one-packet echo buffer
+    localparam BUFFER_SIZE = 256;
+    reg [7:0] pkt_mem [0:BUFFER_SIZE-1];
+
+    reg [15:0] rx_wr_ptr;
+    reg [15:0] rx_pkt_len;
+    reg        rx_pkt_pending;
+
+    // TX -> RX acknowledge toggle
+    reg tx_done_toggle;
+    reg tx_done_toggle_rx_d0, tx_done_toggle_rx_d1;
+    wire tx_done_pulse_rx;
+
+    assign tx_done_pulse_rx = tx_done_toggle_rx_d1 ^ tx_done_toggle_rx_d0;
+
+    always @(posedge gmii_rx_clk or negedge e_rst_n) begin
+        if (!e_rst_n) begin
+            tx_done_toggle_rx_d0 <= 1'b0;
+            tx_done_toggle_rx_d1 <= 1'b0;
+        end else begin
+            tx_done_toggle_rx_d0 <= tx_done_toggle;
+            tx_done_toggle_rx_d1 <= tx_done_toggle_rx_d0;
+        end
+    end
+
+    always @(posedge gmii_rx_clk or negedge e_rst_n) begin
+        if (!e_rst_n) begin
+            rx_wr_ptr        <= 16'd0;
+            rx_pkt_len       <= 16'd0;
+            rx_pkt_pending   <= 1'b0;
+            m_axis_rx_tready <= 1'b0;
+        end else begin
+            // pending lock
+            m_axis_rx_tready <= !rx_pkt_pending;
+
+            // tx free
+            if (tx_done_pulse_rx) begin
+                rx_pkt_pending <= 1'b0;
+                rx_wr_ptr      <= 16'd0;
+            end
+
+            if (m_axis_rx_tvalid && m_axis_rx_tready) begin
+                pkt_mem[rx_wr_ptr] <= m_axis_rx_tdata;
+
+                if (m_axis_rx_tlast) begin
+                    rx_pkt_len     <= rx_wr_ptr + 16'd1;
+                    rx_pkt_pending <= 1'b1;
+                end
+
+                rx_wr_ptr <= rx_wr_ptr + 16'd1;
+            end
+        end
+    end
+
+
+    // sync RX pendind to TX domain
+    reg rx_pkt_pending_tx_d0, rx_pkt_pending_tx_d1;
+
+    always @(posedge gmii_tx_clk or negedge e_rst_n) begin
+        if (!e_rst_n) begin
+            rx_pkt_pending_tx_d0 <= 1'b0;
+            rx_pkt_pending_tx_d1 <= 1'b0;
+        end else begin
+            rx_pkt_pending_tx_d0 <= rx_pkt_pending;
+            rx_pkt_pending_tx_d1 <= rx_pkt_pending_tx_d0;
+        end
+    end
+
+    wire rx_pkt_pending_tx = rx_pkt_pending_tx_d1;
+
+    // tx FSM
+    localparam TX_IDLE    = 2'd0;
+    localparam TX_REQ     = 2'd1;
+    localparam TX_STREAM  = 2'd2;
+    localparam TX_TIMEOUT = 2'd3;
+
+    // timeout counter
+    reg [3:0] timeout_cnt;
+
+    (* MARK_DEBUG="true" *) reg [1:0]  test_state;
+    reg        tx_busy;
+    reg [15:0] tx_pkt_len;
+    reg [15:0] tx_rd_ptr;
+
+    always @(posedge gmii_tx_clk or negedge e_rst_n) begin
+        if (!e_rst_n) begin
+            test_state       <= TX_IDLE;
+            tx_busy          <= 1'b0;
+            tx_pkt_len       <= 16'd0;
+            tx_rd_ptr        <= 16'd0;
+
+            send_req         <= 1'b0;
+            data_length      <= 16'd0;
+
+            s_axis_tx_tdata  <= 8'd0;
+            s_axis_tx_tvalid <= 1'b0;
+            s_axis_tx_tlast  <= 1'b0;
+
+            tx_done_toggle   <= 1'b0;
+            timeout_cnt      <= 4'b0;
+        end else begin
+            send_req <= 1'b0;
+
+            case (test_state)
+                TX_IDLE: begin
+                    s_axis_tx_tvalid <= 1'b0;
+                    s_axis_tx_tlast  <= 1'b0;
+                    tx_rd_ptr        <= 16'd0;
+                    tx_busy          <= 1'b0;
+                    timeout_cnt      <= 4'b0;
+
+                    // rx pending and ready to send
+                    if (rx_pkt_pending_tx && req_ready) begin
+                        tx_busy     <= 1'b1;
+                        tx_pkt_len  <= rx_pkt_len;   // length stable while rx_pkt_pending=1
+                        data_length <= rx_pkt_len;
+                        send_req    <= 1'b1;
+                        test_state    <= TX_REQ;
+                    end
+                end
+
+                TX_REQ: begin
+                    // await ready from axis slave
+                    if (s_axis_tx_tready) begin
+                        s_axis_tx_tdata  <= pkt_mem[0];
+                        s_axis_tx_tvalid <= 1'b1;
+                        s_axis_tx_tlast  <= (tx_pkt_len == 16'd1);
+                        tx_rd_ptr        <= 16'd0;
+                        test_state         <= TX_STREAM;
+                    end
+                end
+
+                TX_STREAM: begin
+                    // now ready to send stream
+                    if (s_axis_tx_tvalid && s_axis_tx_tready) begin
+                        if (tx_rd_ptr == tx_pkt_len - 16'd1) begin
+                            // lset
+                            s_axis_tx_tvalid <= 1'b0;
+                            s_axis_tx_tlast  <= 1'b0;
+                            tx_busy          <= 1'b0;
+                            tx_done_toggle   <= ~tx_done_toggle; 
+                            test_state         <= TX_TIMEOUT;
+                        end else begin
+                            tx_rd_ptr        <= tx_rd_ptr + 16'd1;
+                            s_axis_tx_tdata  <= pkt_mem[tx_rd_ptr + 16'd1];
+                            s_axis_tx_tlast  <= (tx_rd_ptr + 16'd1 == tx_pkt_len - 16'd1);
+                        end
+                    end
+                end
+
+                TX_TIMEOUT: begin
+                    // little timeout until signals syncs
+                    timeout_cnt <= timeout_cnt + 1;
+                    if (timeout_cnt == 4'b1111)
+                        test_state <= TX_IDLE;
+                end
+
+                default: begin
+                    test_state <= TX_IDLE;
+                end
+            endcase
+        end
+    end
+
+    // PHY reset generation
+    reset reset_m0
+    (
+        .clk   (sys_clk),
+        .key1  (rst_n),
+        .rst_n (e_reset)
+    );
+
+endmodule

rtl/ethernet-udp/tests/eth_axis/ethernet_axis_echo.xdc

@@ -0,0 +1,346 @@
+# constrains for minimal ethernet stack
+
+create_clock -period 5.000 [get_ports sys_clk_p]
+set_property IOSTANDARD DIFF_SSTL15 [get_ports sys_clk_p]
+set_property IOSTANDARD DIFF_SSTL15 [get_ports sys_clk_n]
+set_property PACKAGE_PIN R4 [get_ports sys_clk_p]
+set_property PACKAGE_PIN T4 [get_ports sys_clk_n]
+
+set_property PACKAGE_PIN F15 [get_ports rst_n]
+set_property IOSTANDARD LVCMOS33 [get_ports rst_n]
+
+set_property PACKAGE_PIN L13 [get_ports {led[0]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {led[0]}]
+set_property PACKAGE_PIN M13 [get_ports {led[1]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {led[1]}]
+set_property PACKAGE_PIN K14 [get_ports {led[2]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {led[2]}]
+set_property PACKAGE_PIN K13 [get_ports {led[3]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {led[3]}]
+#########################ethernet######################
+create_clock -period 8.000 [get_ports rgmii_rxc]
+set_property IOSTANDARD LVCMOS33 [get_ports {rgmii_rxd[*]}]
+set_property IOSTANDARD LVCMOS33 [get_ports {rgmii_txd[*]}]
+set_property SLEW FAST [get_ports {rgmii_txd[*]}]
+
+set_property IOSTANDARD LVCMOS33 [get_ports e_mdc]
+set_property IOSTANDARD LVCMOS33 [get_ports e_mdio]
+set_property IOSTANDARD LVCMOS33 [get_ports e_reset]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_rxc]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_rxctl]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_txc]
+set_property IOSTANDARD LVCMOS33 [get_ports rgmii_txctl]
+set_property SLEW FAST [get_ports rgmii_txc]
+set_property SLEW FAST [get_ports rgmii_txctl]
+
+set_property PACKAGE_PIN P17 [get_ports {rgmii_rxd[3]}]
+set_property PACKAGE_PIN U17 [get_ports {rgmii_rxd[2]}]
+set_property PACKAGE_PIN U18 [get_ports {rgmii_rxd[1]}]
+set_property PACKAGE_PIN P19 [get_ports {rgmii_rxd[0]}]
+set_property PACKAGE_PIN R16 [get_ports {rgmii_txd[3]}]
+set_property PACKAGE_PIN R17 [get_ports {rgmii_txd[2]}]
+set_property PACKAGE_PIN P16 [get_ports {rgmii_txd[1]}]
+set_property PACKAGE_PIN N14 [get_ports {rgmii_txd[0]}]
+set_property PACKAGE_PIN N13 [get_ports e_mdc]
+set_property PACKAGE_PIN P14 [get_ports e_mdio]
+set_property PACKAGE_PIN R14 [get_ports e_reset]
+set_property PACKAGE_PIN V18 [get_ports rgmii_rxc]
+set_property PACKAGE_PIN R19 [get_ports rgmii_rxctl]
+set_property PACKAGE_PIN P15 [get_ports rgmii_txc]
+set_property PACKAGE_PIN N17 [get_ports rgmii_txctl]
+
+
+
+
+connect_debug_port u_ila_0/clk [get_nets [list gmii_tx_clk_IBUF_BUFG]]
+connect_debug_port u_ila_0/probe0 [get_nets [list {dut/mac_top0/mac_tx0/mac_tx_data[0]} {dut/mac_top0/mac_tx0/mac_tx_data[1]} {dut/mac_top0/mac_tx0/mac_tx_data[2]} {dut/mac_top0/mac_tx0/mac_tx_data[3]} {dut/mac_top0/mac_tx0/mac_tx_data[4]} {dut/mac_top0/mac_tx0/mac_tx_data[5]} {dut/mac_top0/mac_tx0/mac_tx_data[6]} {dut/mac_top0/mac_tx0/mac_tx_data[7]}]]
+connect_debug_port u_ila_0/probe1 [get_nets [list {dut/mac_top0/mac_tx0/ram_wr_data[0]} {dut/mac_top0/mac_tx0/ram_wr_data[1]} {dut/mac_top0/mac_tx0/ram_wr_data[2]} {dut/mac_top0/mac_tx0/ram_wr_data[3]} {dut/mac_top0/mac_tx0/ram_wr_data[4]} {dut/mac_top0/mac_tx0/ram_wr_data[5]} {dut/mac_top0/mac_tx0/ram_wr_data[6]} {dut/mac_top0/mac_tx0/ram_wr_data[7]}]]
+connect_debug_port u_ila_0/probe2 [get_nets [list {dut/mac_top0/mac_tx0/udp0/usedw[0]} {dut/mac_top0/mac_tx0/udp0/usedw[1]} {dut/mac_top0/mac_tx0/udp0/usedw[2]} {dut/mac_top0/mac_tx0/udp0/usedw[3]}]]
+connect_debug_port u_ila_0/probe3 [get_nets [list {dut/mac_top0/mac_tx0/udp0/state[0]} {dut/mac_top0/mac_tx0/udp0/state[1]} {dut/mac_top0/mac_tx0/udp0/state[2]} {dut/mac_top0/mac_tx0/udp0/state[3]} {dut/mac_top0/mac_tx0/udp0/state[4]} {dut/mac_top0/mac_tx0/udp0/state[5]}]]
+connect_debug_port u_ila_0/probe4 [get_nets [list {dut/mac_top0/mac_tx0/udp_send_data_length[0]} {dut/mac_top0/mac_tx0/udp_send_data_length[1]} {dut/mac_top0/mac_tx0/udp_send_data_length[2]} {dut/mac_top0/mac_tx0/udp_send_data_length[3]} {dut/mac_top0/mac_tx0/udp_send_data_length[4]} {dut/mac_top0/mac_tx0/udp_send_data_length[5]} {dut/mac_top0/mac_tx0/udp_send_data_length[6]} {dut/mac_top0/mac_tx0/udp_send_data_length[7]} {dut/mac_top0/mac_tx0/udp_send_data_length[8]} {dut/mac_top0/mac_tx0/udp_send_data_length[9]} {dut/mac_top0/mac_tx0/udp_send_data_length[10]} {dut/mac_top0/mac_tx0/udp_send_data_length[11]} {dut/mac_top0/mac_tx0/udp_send_data_length[12]} {dut/mac_top0/mac_tx0/udp_send_data_length[13]} {dut/mac_top0/mac_tx0/udp_send_data_length[14]} {dut/mac_top0/mac_tx0/udp_send_data_length[15]}]]
+connect_debug_port u_ila_0/probe5 [get_nets [list {dut/mac_top0/mac_tx0/udp_ram_data_count[0]} {dut/mac_top0/mac_tx0/udp_ram_data_count[1]} {dut/mac_top0/mac_tx0/udp_ram_data_count[2]} {dut/mac_top0/mac_tx0/udp_ram_data_count[3]} {dut/mac_top0/mac_tx0/udp_ram_data_count[4]} {dut/mac_top0/mac_tx0/udp_ram_data_count[5]} {dut/mac_top0/mac_tx0/udp_ram_data_count[6]} {dut/mac_top0/mac_tx0/udp_ram_data_count[7]} {dut/mac_top0/mac_tx0/udp_ram_data_count[8]} {dut/mac_top0/mac_tx0/udp_ram_data_count[9]} {dut/mac_top0/mac_tx0/udp_ram_data_count[10]} {dut/mac_top0/mac_tx0/udp_ram_data_count[11]}]]
+connect_debug_port u_ila_0/probe6 [get_nets [list {dut/mac_top0/mac_tx0/udp0/ck_state[0]} {dut/mac_top0/mac_tx0/udp0/ck_state[1]} {dut/mac_top0/mac_tx0/udp0/ck_state[2]} {dut/mac_top0/mac_tx0/udp0/ck_state[3]} {dut/mac_top0/mac_tx0/udp0/ck_state[4]} {dut/mac_top0/mac_tx0/udp0/ck_state[5]}]]
+connect_debug_port u_ila_0/probe7 [get_nets [list dut/mac_top0/mac_tx0/almost_full]]
+connect_debug_port u_ila_0/probe8 [get_nets [list dut/mac_top0/mac_tx0/mac_data_valid]]
+connect_debug_port u_ila_0/probe9 [get_nets [list dut/mac_top0/mac_tx0/mac_send_end]]
+connect_debug_port u_ila_0/probe10 [get_nets [list dut/mac_top0/mac_tx0/ram_wr_en]]
+connect_debug_port u_ila_0/probe11 [get_nets [list dut/mac_top0/mac_tx0/udp_ram_data_req]]
+connect_debug_port u_ila_0/probe12 [get_nets [list dut/mac_top0/mac_tx0/udp_tx_end]]
+connect_debug_port u_ila_0/probe13 [get_nets [list dut/mac_top0/mac_tx0/udp_tx_req]]
+connect_debug_port u_ila_0/probe14 [get_nets [list dut/mac_top0/mac_tx0/upper_data_req]]
+connect_debug_port u_ila_1/clk [get_nets [list gmii_rx_clk_IBUF_BUFG]]
+connect_debug_port u_ila_1/probe0 [get_nets [list {dut/udp_rec_data_length[0]} {dut/udp_rec_data_length[1]} {dut/udp_rec_data_length[2]} {dut/udp_rec_data_length[3]} {dut/udp_rec_data_length[4]} {dut/udp_rec_data_length[5]} {dut/udp_rec_data_length[6]} {dut/udp_rec_data_length[7]} {dut/udp_rec_data_length[8]} {dut/udp_rec_data_length[9]} {dut/udp_rec_data_length[10]} {dut/udp_rec_data_length[11]} {dut/udp_rec_data_length[12]} {dut/udp_rec_data_length[13]} {dut/udp_rec_data_length[14]} {dut/udp_rec_data_length[15]}]]
+connect_debug_port u_ila_1/probe1 [get_nets [list {dut/rx_index[0]} {dut/rx_index[1]} {dut/rx_index[2]} {dut/rx_index[3]} {dut/rx_index[4]} {dut/rx_index[5]} {dut/rx_index[6]} {dut/rx_index[7]} {dut/rx_index[8]} {dut/rx_index[9]} {dut/rx_index[10]} {dut/rx_index[11]} {dut/rx_index[12]} {dut/rx_index[13]} {dut/rx_index[14]} {dut/rx_index[15]}]]
+connect_debug_port u_ila_1/probe2 [get_nets [list {dut/m_axis_rx_tdata[0]} {dut/m_axis_rx_tdata[1]} {dut/m_axis_rx_tdata[2]} {dut/m_axis_rx_tdata[3]} {dut/m_axis_rx_tdata[4]} {dut/m_axis_rx_tdata[5]} {dut/m_axis_rx_tdata[6]} {dut/m_axis_rx_tdata[7]}]]
+connect_debug_port u_ila_1/probe3 [get_nets [list {dut/rx_state[0]} {dut/rx_state[1]}]]
+connect_debug_port u_ila_1/probe4 [get_nets [list {dut/rx_payload_len[0]} {dut/rx_payload_len[1]} {dut/rx_payload_len[2]} {dut/rx_payload_len[3]} {dut/rx_payload_len[4]} {dut/rx_payload_len[5]} {dut/rx_payload_len[6]} {dut/rx_payload_len[7]} {dut/rx_payload_len[8]} {dut/rx_payload_len[9]} {dut/rx_payload_len[10]} {dut/rx_payload_len[11]} {dut/rx_payload_len[12]} {dut/rx_payload_len[13]} {dut/rx_payload_len[14]} {dut/rx_payload_len[15]}]]
+connect_debug_port u_ila_1/probe5 [get_nets [list {dut/mac_top0/mac_rx0/ip_total_data_length[0]} {dut/mac_top0/mac_rx0/ip_total_data_length[1]} {dut/mac_top0/mac_rx0/ip_total_data_length[2]} {dut/mac_top0/mac_rx0/ip_total_data_length[3]} {dut/mac_top0/mac_rx0/ip_total_data_length[4]} {dut/mac_top0/mac_rx0/ip_total_data_length[5]} {dut/mac_top0/mac_rx0/ip_total_data_length[6]} {dut/mac_top0/mac_rx0/ip_total_data_length[7]} {dut/mac_top0/mac_rx0/ip_total_data_length[8]} {dut/mac_top0/mac_rx0/ip_total_data_length[9]} {dut/mac_top0/mac_rx0/ip_total_data_length[10]} {dut/mac_top0/mac_rx0/ip_total_data_length[11]} {dut/mac_top0/mac_rx0/ip_total_data_length[12]} {dut/mac_top0/mac_rx0/ip_total_data_length[13]} {dut/mac_top0/mac_rx0/ip_total_data_length[14]} {dut/mac_top0/mac_rx0/ip_total_data_length[15]}]]
+connect_debug_port u_ila_1/probe6 [get_nets [list {dut/mac_top0/mac_rx0/upper_layer_data_length[0]} {dut/mac_top0/mac_rx0/upper_layer_data_length[1]} {dut/mac_top0/mac_rx0/upper_layer_data_length[2]} {dut/mac_top0/mac_rx0/upper_layer_data_length[3]} {dut/mac_top0/mac_rx0/upper_layer_data_length[4]} {dut/mac_top0/mac_rx0/upper_layer_data_length[5]} {dut/mac_top0/mac_rx0/upper_layer_data_length[6]} {dut/mac_top0/mac_rx0/upper_layer_data_length[7]} {dut/mac_top0/mac_rx0/upper_layer_data_length[8]} {dut/mac_top0/mac_rx0/upper_layer_data_length[9]} {dut/mac_top0/mac_rx0/upper_layer_data_length[10]} {dut/mac_top0/mac_rx0/upper_layer_data_length[11]} {dut/mac_top0/mac_rx0/upper_layer_data_length[12]} {dut/mac_top0/mac_rx0/upper_layer_data_length[13]} {dut/mac_top0/mac_rx0/upper_layer_data_length[14]} {dut/mac_top0/mac_rx0/upper_layer_data_length[15]}]]
+connect_debug_port u_ila_1/probe7 [get_nets [list {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[0]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[1]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[2]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[3]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[4]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[5]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[6]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[7]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[8]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[9]} {dut/mac_top0/mac_rx0/udp_rec_ram_read_addr[10]}]]
+connect_debug_port u_ila_1/probe8 [get_nets [list {dut/mac_top0/mac_rx0/mac_rx_datain[0]} {dut/mac_top0/mac_rx0/mac_rx_datain[1]} {dut/mac_top0/mac_rx0/mac_rx_datain[2]} {dut/mac_top0/mac_rx0/mac_rx_datain[3]} {dut/mac_top0/mac_rx0/mac_rx_datain[4]} {dut/mac_top0/mac_rx0/mac_rx_datain[5]} {dut/mac_top0/mac_rx0/mac_rx_datain[6]} {dut/mac_top0/mac_rx0/mac_rx_datain[7]}]]
+connect_debug_port u_ila_1/probe9 [get_nets [list {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[0]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[1]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[2]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[3]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[4]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[5]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[6]} {dut/mac_top0/mac_rx0/udp_rec_ram_rdata[7]}]]
+connect_debug_port u_ila_1/probe10 [get_nets [list {dut/mac_top0/mac_rx0/mac_rx_dataout[0]} {dut/mac_top0/mac_rx0/mac_rx_dataout[1]} {dut/mac_top0/mac_rx0/mac_rx_dataout[2]} {dut/mac_top0/mac_rx0/mac_rx_dataout[3]} {dut/mac_top0/mac_rx0/mac_rx_dataout[4]} {dut/mac_top0/mac_rx0/mac_rx_dataout[5]} {dut/mac_top0/mac_rx0/mac_rx_dataout[6]} {dut/mac_top0/mac_rx0/mac_rx_dataout[7]}]]
+connect_debug_port u_ila_1/probe11 [get_nets [list {dut/mac_top0/mac_rx0/udp_rec_data_length[0]} {dut/mac_top0/mac_rx0/udp_rec_data_length[1]} {dut/mac_top0/mac_rx0/udp_rec_data_length[2]} {dut/mac_top0/mac_rx0/udp_rec_data_length[3]} {dut/mac_top0/mac_rx0/udp_rec_data_length[4]} {dut/mac_top0/mac_rx0/udp_rec_data_length[5]} {dut/mac_top0/mac_rx0/udp_rec_data_length[6]} {dut/mac_top0/mac_rx0/udp_rec_data_length[7]} {dut/mac_top0/mac_rx0/udp_rec_data_length[8]} {dut/mac_top0/mac_rx0/udp_rec_data_length[9]} {dut/mac_top0/mac_rx0/udp_rec_data_length[10]} {dut/mac_top0/mac_rx0/udp_rec_data_length[11]} {dut/mac_top0/mac_rx0/udp_rec_data_length[12]} {dut/mac_top0/mac_rx0/udp_rec_data_length[13]} {dut/mac_top0/mac_rx0/udp_rec_data_length[14]} {dut/mac_top0/mac_rx0/udp_rec_data_length[15]}]]
+connect_debug_port u_ila_1/probe12 [get_nets [list {dut/mac_top0/mac_rx0/udp0/ram_write_addr[0]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[1]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[2]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[3]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[4]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[5]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[6]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[7]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[8]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[9]} {dut/mac_top0/mac_rx0/udp0/ram_write_addr[10]}]]
+connect_debug_port u_ila_1/probe13 [get_nets [list dut/m_axis_rx_tlast]]
+connect_debug_port u_ila_1/probe14 [get_nets [list dut/m_axis_rx_tvalid]]
+connect_debug_port u_ila_1/probe15 [get_nets [list dut/mac_top0/mac_rx0/udp0/ram_wr_en]]
+connect_debug_port u_ila_1/probe16 [get_nets [list dut/mac_top0/mac_rx0/udp_rec_data_valid]]
+connect_debug_port dbg_hub/clk [get_nets gmii_rx_clk_IBUF_BUFG]
+
+
+
+connect_debug_port u_ila_0/probe4 [get_nets [list {tx_state[0]} {tx_state[1]}]]
+
+connect_debug_port u_ila_0/probe48 [get_nets [list rx_pkt_pulse_tx]]
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 8 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {axis_mac0/mac_top0/mac_tx0/ram_wr_data[0]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[1]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[2]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[3]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[4]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[5]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[6]} {axis_mac0/mac_top0/mac_tx0/ram_wr_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 8 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {axis_mac0/mac_top0/mac_tx0/mac_tx_data[0]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[1]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[2]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[3]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[4]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[5]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[6]} {axis_mac0/mac_top0/mac_tx0/mac_tx_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 16 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {axis_mac0/rx_payload_len[0]} {axis_mac0/rx_payload_len[1]} {axis_mac0/rx_payload_len[2]} {axis_mac0/rx_payload_len[3]} {axis_mac0/rx_payload_len[4]} {axis_mac0/rx_payload_len[5]} {axis_mac0/rx_payload_len[6]} {axis_mac0/rx_payload_len[7]} {axis_mac0/rx_payload_len[8]} {axis_mac0/rx_payload_len[9]} {axis_mac0/rx_payload_len[10]} {axis_mac0/rx_payload_len[11]} {axis_mac0/rx_payload_len[12]} {axis_mac0/rx_payload_len[13]} {axis_mac0/rx_payload_len[14]} {axis_mac0/rx_payload_len[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 16 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list {axis_mac0/rx_index[0]} {axis_mac0/rx_index[1]} {axis_mac0/rx_index[2]} {axis_mac0/rx_index[3]} {axis_mac0/rx_index[4]} {axis_mac0/rx_index[5]} {axis_mac0/rx_index[6]} {axis_mac0/rx_index[7]} {axis_mac0/rx_index[8]} {axis_mac0/rx_index[9]} {axis_mac0/rx_index[10]} {axis_mac0/rx_index[11]} {axis_mac0/rx_index[12]} {axis_mac0/rx_index[13]} {axis_mac0/rx_index[14]} {axis_mac0/rx_index[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 16 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[0]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[1]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[2]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[3]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[4]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[5]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[6]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[7]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[8]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[9]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[10]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[11]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[12]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[13]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[14]} {axis_mac0/mac_top0/mac_tx0/udp_send_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 12 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[0]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[1]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[2]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[3]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[4]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[5]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[6]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[7]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[8]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[9]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[10]} {axis_mac0/mac_top0/mac_tx0/udp_ram_data_count[11]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 11 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[7]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[8]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[9]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_read_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe7]
+set_property port_width 8 [get_debug_ports u_ila_0/probe7]
+connect_debug_port u_ila_0/probe7 [get_nets [list {arbi_inst/e_txd[0]} {arbi_inst/e_txd[1]} {arbi_inst/e_txd[2]} {arbi_inst/e_txd[3]} {arbi_inst/e_txd[4]} {arbi_inst/e_txd[5]} {arbi_inst/e_txd[6]} {arbi_inst/e_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe8]
+set_property port_width 8 [get_debug_ports u_ila_0/probe8]
+connect_debug_port u_ila_0/probe8 [get_nets [list {arbi_inst/tx_buffer_inst/tx_rdata[0]} {arbi_inst/tx_buffer_inst/tx_rdata[1]} {arbi_inst/tx_buffer_inst/tx_rdata[2]} {arbi_inst/tx_buffer_inst/tx_rdata[3]} {arbi_inst/tx_buffer_inst/tx_rdata[4]} {arbi_inst/tx_buffer_inst/tx_rdata[5]} {arbi_inst/tx_buffer_inst/tx_rdata[6]} {arbi_inst/tx_buffer_inst/tx_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe9]
+set_property port_width 16 [get_debug_ports u_ila_0/probe9]
+connect_debug_port u_ila_0/probe9 [get_nets [list {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[0]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[1]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[2]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[3]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[4]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[5]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[6]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[7]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[8]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[9]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[10]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[11]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[12]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[13]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[14]} {axis_mac0/mac_top0/mac_rx0/ip_total_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe10]
+set_property port_width 8 [get_debug_ports u_ila_0/probe10]
+connect_debug_port u_ila_0/probe10 [get_nets [list {axis_mac0/m_axis_rx_tdata[0]} {axis_mac0/m_axis_rx_tdata[1]} {axis_mac0/m_axis_rx_tdata[2]} {axis_mac0/m_axis_rx_tdata[3]} {axis_mac0/m_axis_rx_tdata[4]} {axis_mac0/m_axis_rx_tdata[5]} {axis_mac0/m_axis_rx_tdata[6]} {axis_mac0/m_axis_rx_tdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe11]
+set_property port_width 8 [get_debug_ports u_ila_0/probe11]
+connect_debug_port u_ila_0/probe11 [get_nets [list {arbi_inst/rx_buffer_inst/e10_100_rxd[0]} {arbi_inst/rx_buffer_inst/e10_100_rxd[1]} {arbi_inst/rx_buffer_inst/e10_100_rxd[2]} {arbi_inst/rx_buffer_inst/e10_100_rxd[3]} {arbi_inst/rx_buffer_inst/e10_100_rxd[4]} {arbi_inst/rx_buffer_inst/e10_100_rxd[5]} {arbi_inst/rx_buffer_inst/e10_100_rxd[6]} {arbi_inst/rx_buffer_inst/e10_100_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe12]
+set_property port_width 8 [get_debug_ports u_ila_0/probe12]
+connect_debug_port u_ila_0/probe12 [get_nets [list {axis_mac0/s_axis_tx_tdata[0]} {axis_mac0/s_axis_tx_tdata[1]} {axis_mac0/s_axis_tx_tdata[2]} {axis_mac0/s_axis_tx_tdata[3]} {axis_mac0/s_axis_tx_tdata[4]} {axis_mac0/s_axis_tx_tdata[5]} {axis_mac0/s_axis_tx_tdata[6]} {axis_mac0/s_axis_tx_tdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe13]
+set_property port_width 11 [get_debug_ports u_ila_0/probe13]
+connect_debug_port u_ila_0/probe13 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[0]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[1]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[2]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[3]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[4]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[5]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[6]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[7]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[8]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[9]} {axis_mac0/mac_top0/mac_rx0/udp0/ram_write_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe14]
+set_property port_width 8 [get_debug_ports u_ila_0/probe14]
+connect_debug_port u_ila_0/probe14 [get_nets [list {arbi_inst/e_rxd[0]} {arbi_inst/e_rxd[1]} {arbi_inst/e_rxd[2]} {arbi_inst/e_rxd[3]} {arbi_inst/e_rxd[4]} {arbi_inst/e_rxd[5]} {arbi_inst/e_rxd[6]} {arbi_inst/e_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe15]
+set_property port_width 8 [get_debug_ports u_ila_0/probe15]
+connect_debug_port u_ila_0/probe15 [get_nets [list {arbi_inst/gmii_txd[0]} {arbi_inst/gmii_txd[1]} {arbi_inst/gmii_txd[2]} {arbi_inst/gmii_txd[3]} {arbi_inst/gmii_txd[4]} {arbi_inst/gmii_txd[5]} {arbi_inst/gmii_txd[6]} {arbi_inst/gmii_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe16]
+set_property port_width 16 [get_debug_ports u_ila_0/probe16]
+connect_debug_port u_ila_0/probe16 [get_nets [list {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[0]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[1]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[2]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[3]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[4]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[5]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[6]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[7]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[8]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[9]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[10]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[11]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[12]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[13]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[14]} {axis_mac0/mac_top0/mac_rx0/upper_layer_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe17]
+set_property port_width 2 [get_debug_ports u_ila_0/probe17]
+connect_debug_port u_ila_0/probe17 [get_nets [list {test_state[0]} {test_state[1]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe18]
+set_property port_width 8 [get_debug_ports u_ila_0/probe18]
+connect_debug_port u_ila_0/probe18 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_ram_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe19]
+set_property port_width 6 [get_debug_ports u_ila_0/probe19]
+connect_debug_port u_ila_0/probe19 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/state[0]} {axis_mac0/mac_top0/mac_tx0/udp0/state[1]} {axis_mac0/mac_top0/mac_tx0/udp0/state[2]} {axis_mac0/mac_top0/mac_tx0/udp0/state[3]} {axis_mac0/mac_top0/mac_tx0/udp0/state[4]} {axis_mac0/mac_top0/mac_tx0/udp0/state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe20]
+set_property port_width 8 [get_debug_ports u_ila_0/probe20]
+connect_debug_port u_ila_0/probe20 [get_nets [list {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[0]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[1]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[2]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[3]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[4]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[5]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[6]} {axis_mac0/mac_top0/mac_rx0/mac_rx_datain[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe21]
+set_property port_width 16 [get_debug_ports u_ila_0/probe21]
+connect_debug_port u_ila_0/probe21 [get_nets [list {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[0]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[1]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[2]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[3]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[4]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[5]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[6]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[7]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[8]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[9]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[10]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[11]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[12]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[13]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[14]} {axis_mac0/mac_top0/mac_rx0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe22]
+set_property port_width 4 [get_debug_ports u_ila_0/probe22]
+connect_debug_port u_ila_0/probe22 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/usedw[0]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[1]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[2]} {axis_mac0/mac_top0/mac_tx0/udp0/usedw[3]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe23]
+set_property port_width 6 [get_debug_ports u_ila_0/probe23]
+connect_debug_port u_ila_0/probe23 [get_nets [list {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[0]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[1]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[2]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[3]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[4]} {axis_mac0/mac_top0/mac_tx0/udp0/ck_state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe24]
+set_property port_width 8 [get_debug_ports u_ila_0/probe24]
+connect_debug_port u_ila_0/probe24 [get_nets [list {arbi_inst/gmii_rxd[0]} {arbi_inst/gmii_rxd[1]} {arbi_inst/gmii_rxd[2]} {arbi_inst/gmii_rxd[3]} {arbi_inst/gmii_rxd[4]} {arbi_inst/gmii_rxd[5]} {arbi_inst/gmii_rxd[6]} {arbi_inst/gmii_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe25]
+set_property port_width 2 [get_debug_ports u_ila_0/probe25]
+connect_debug_port u_ila_0/probe25 [get_nets [list {axis_mac0/rx_state[0]} {axis_mac0/rx_state[1]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe26]
+set_property port_width 8 [get_debug_ports u_ila_0/probe26]
+connect_debug_port u_ila_0/probe26 [get_nets [list {arbi_inst/tx_buffer_inst/tx_wdata[0]} {arbi_inst/tx_buffer_inst/tx_wdata[1]} {arbi_inst/tx_buffer_inst/tx_wdata[2]} {arbi_inst/tx_buffer_inst/tx_wdata[3]} {arbi_inst/tx_buffer_inst/tx_wdata[4]} {arbi_inst/tx_buffer_inst/tx_wdata[5]} {arbi_inst/tx_buffer_inst/tx_wdata[6]} {arbi_inst/tx_buffer_inst/tx_wdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe27]
+set_property port_width 8 [get_debug_ports u_ila_0/probe27]
+connect_debug_port u_ila_0/probe27 [get_nets [list {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[0]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[1]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[2]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[3]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[4]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[5]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[6]} {axis_mac0/mac_top0/mac_rx0/mac_rx_dataout[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe28]
+set_property port_width 3 [get_debug_ports u_ila_0/probe28]
+connect_debug_port u_ila_0/probe28 [get_nets [list {axis_mac0/tx_state[0]} {axis_mac0/tx_state[1]} {axis_mac0/tx_state[2]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe29]
+set_property port_width 16 [get_debug_ports u_ila_0/probe29]
+connect_debug_port u_ila_0/probe29 [get_nets [list {arbi_inst/tx_buffer_inst/tx_data_cnt[0]} {arbi_inst/tx_buffer_inst/tx_data_cnt[1]} {arbi_inst/tx_buffer_inst/tx_data_cnt[2]} {arbi_inst/tx_buffer_inst/tx_data_cnt[3]} {arbi_inst/tx_buffer_inst/tx_data_cnt[4]} {arbi_inst/tx_buffer_inst/tx_data_cnt[5]} {arbi_inst/tx_buffer_inst/tx_data_cnt[6]} {arbi_inst/tx_buffer_inst/tx_data_cnt[7]} {arbi_inst/tx_buffer_inst/tx_data_cnt[8]} {arbi_inst/tx_buffer_inst/tx_data_cnt[9]} {arbi_inst/tx_buffer_inst/tx_data_cnt[10]} {arbi_inst/tx_buffer_inst/tx_data_cnt[11]} {arbi_inst/tx_buffer_inst/tx_data_cnt[12]} {arbi_inst/tx_buffer_inst/tx_data_cnt[13]} {arbi_inst/tx_buffer_inst/tx_data_cnt[14]} {arbi_inst/tx_buffer_inst/tx_data_cnt[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe30]
+set_property port_width 16 [get_debug_ports u_ila_0/probe30]
+connect_debug_port u_ila_0/probe30 [get_nets [list {axis_mac0/udp_rec_data_length[0]} {axis_mac0/udp_rec_data_length[1]} {axis_mac0/udp_rec_data_length[2]} {axis_mac0/udp_rec_data_length[3]} {axis_mac0/udp_rec_data_length[4]} {axis_mac0/udp_rec_data_length[5]} {axis_mac0/udp_rec_data_length[6]} {axis_mac0/udp_rec_data_length[7]} {axis_mac0/udp_rec_data_length[8]} {axis_mac0/udp_rec_data_length[9]} {axis_mac0/udp_rec_data_length[10]} {axis_mac0/udp_rec_data_length[11]} {axis_mac0/udp_rec_data_length[12]} {axis_mac0/udp_rec_data_length[13]} {axis_mac0/udp_rec_data_length[14]} {axis_mac0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe31]
+set_property port_width 1 [get_debug_ports u_ila_0/probe31]
+connect_debug_port u_ila_0/probe31 [get_nets [list axis_mac0/mac_top0/mac_tx0/almost_full]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe32]
+set_property port_width 1 [get_debug_ports u_ila_0/probe32]
+connect_debug_port u_ila_0/probe32 [get_nets [list axis_mac0/arp_found]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe33]
+set_property port_width 1 [get_debug_ports u_ila_0/probe33]
+connect_debug_port u_ila_0/probe33 [get_nets [list arbi_inst/rx_buffer_inst/e10_100_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe34]
+set_property port_width 1 [get_debug_ports u_ila_0/probe34]
+connect_debug_port u_ila_0/probe34 [get_nets [list arbi_inst/e_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe35]
+set_property port_width 1 [get_debug_ports u_ila_0/probe35]
+connect_debug_port u_ila_0/probe35 [get_nets [list arbi_inst/e_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe36]
+set_property port_width 1 [get_debug_ports u_ila_0/probe36]
+connect_debug_port u_ila_0/probe36 [get_nets [list arbi_inst/gmii_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe37]
+set_property port_width 1 [get_debug_ports u_ila_0/probe37]
+connect_debug_port u_ila_0/probe37 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d0]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe38]
+set_property port_width 1 [get_debug_ports u_ila_0/probe38]
+connect_debug_port u_ila_0/probe38 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d1]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe39]
+set_property port_width 1 [get_debug_ports u_ila_0/probe39]
+connect_debug_port u_ila_0/probe39 [get_nets [list arbi_inst/gmii_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe40]
+set_property port_width 1 [get_debug_ports u_ila_0/probe40]
+connect_debug_port u_ila_0/probe40 [get_nets [list axis_mac0/m_axis_rx_tlast]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe41]
+set_property port_width 1 [get_debug_ports u_ila_0/probe41]
+connect_debug_port u_ila_0/probe41 [get_nets [list axis_mac0/m_axis_rx_tready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe42]
+set_property port_width 1 [get_debug_ports u_ila_0/probe42]
+connect_debug_port u_ila_0/probe42 [get_nets [list axis_mac0/m_axis_rx_tvalid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe43]
+set_property port_width 1 [get_debug_ports u_ila_0/probe43]
+connect_debug_port u_ila_0/probe43 [get_nets [list axis_mac0/mac_top0/mac_tx0/mac_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe44]
+set_property port_width 1 [get_debug_ports u_ila_0/probe44]
+connect_debug_port u_ila_0/probe44 [get_nets [list axis_mac0/mac_top0/mac_tx0/mac_send_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe45]
+set_property port_width 1 [get_debug_ports u_ila_0/probe45]
+connect_debug_port u_ila_0/probe45 [get_nets [list axis_mac0/mac_top0/mac_tx0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe46]
+set_property port_width 1 [get_debug_ports u_ila_0/probe46]
+connect_debug_port u_ila_0/probe46 [get_nets [list axis_mac0/mac_top0/mac_rx0/udp0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe47]
+set_property port_width 1 [get_debug_ports u_ila_0/probe47]
+connect_debug_port u_ila_0/probe47 [get_nets [list req_ready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe48]
+set_property port_width 1 [get_debug_ports u_ila_0/probe48]
+connect_debug_port u_ila_0/probe48 [get_nets [list axis_mac0/s_axis_tx_tlast]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe49]
+set_property port_width 1 [get_debug_ports u_ila_0/probe49]
+connect_debug_port u_ila_0/probe49 [get_nets [list axis_mac0/s_axis_tx_tready]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe50]
+set_property port_width 1 [get_debug_ports u_ila_0/probe50]
+connect_debug_port u_ila_0/probe50 [get_nets [list axis_mac0/s_axis_tx_tvalid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe51]
+set_property port_width 1 [get_debug_ports u_ila_0/probe51]
+connect_debug_port u_ila_0/probe51 [get_nets [list send_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe52]
+set_property port_width 1 [get_debug_ports u_ila_0/probe52]
+connect_debug_port u_ila_0/probe52 [get_nets [list arbi_inst/tx_buffer_inst/tx_rden]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe53]
+set_property port_width 1 [get_debug_ports u_ila_0/probe53]
+connect_debug_port u_ila_0/probe53 [get_nets [list arbi_inst/tx_buffer_inst/tx_wren]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe54]
+set_property port_width 1 [get_debug_ports u_ila_0/probe54]
+connect_debug_port u_ila_0/probe54 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_ram_data_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe55]
+set_property port_width 1 [get_debug_ports u_ila_0/probe55]
+connect_debug_port u_ila_0/probe55 [get_nets [list axis_mac0/mac_top0/mac_rx0/udp_rec_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe56]
+set_property port_width 1 [get_debug_ports u_ila_0/probe56]
+connect_debug_port u_ila_0/probe56 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_tx_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe57]
+set_property port_width 1 [get_debug_ports u_ila_0/probe57]
+connect_debug_port u_ila_0/probe57 [get_nets [list axis_mac0/mac_top0/mac_tx0/udp_tx_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe58]
+set_property port_width 1 [get_debug_ports u_ila_0/probe58]
+connect_debug_port u_ila_0/probe58 [get_nets [list axis_mac0/mac_top0/mac_tx0/upper_data_req]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets rgmii_rxc_IBUF_BUFG]

rtl/ethernet-udp/tests/eth_axis/test_axis_mac_rx.sv

@@ -11,17 +11,27 @@ module tb_mac_test;
     wire        gmii_tx_en;
     wire [7:0]  gmii_txd;
 
+    // rx axis
     wire [7:0]  m_axis_rx_tdata;
     wire        m_axis_rx_tvalid;
     reg         m_axis_rx_tready = 1'b0;
     wire        m_axis_rx_tlast;
 
+    // tx axis
+    reg  [7:0]  s_axis_tx_tdata;
+    reg         s_axis_tx_tvalid;
+    wire        s_axis_tx_tready = 1'b0;
+    reg         s_axis_tx_tlast;
+
+    reg send_req;
+    wire req_ready;
+
+    reg [15:0] udp_rec_data_length;
+    
     int cnt = 0;
 
 
-    // ============================================================
     // DUT
-    // ============================================================
     axis_mac dut (
         .rst_n(rst_n),
         .gmii_tx_clk(gmii_tx_clk),
@@ -33,18 +43,22 @@ module tb_mac_test;
         .m_axis_rx_tdata(m_axis_rx_tdata),
         .m_axis_rx_tvalid(m_axis_rx_tvalid),
         .m_axis_rx_tready(m_axis_rx_tready),
-        .m_axis_rx_tlast(m_axis_rx_tlast)
+        .m_axis_rx_tlast(m_axis_rx_tlast),
+        .s_axis_tx_tdata(s_axis_tx_tdata),
+        .s_axis_tx_tvalid(s_axis_tx_tvalid),
+        .s_axis_tx_tready(s_axis_tx_tready),
+        .s_axis_tx_tlast(s_axis_tx_tlast),
+        .send_req(send_req),
+        .req_ready(req_ready),
+        .udp_rec_data_length(udp_rec_data_length)
+
     );
 
-    // ============================================================
     // Clocks
-    // ============================================================
     always #4 gmii_rx_clk = ~gmii_rx_clk;
     always #4 gmii_tx_clk = ~gmii_tx_clk;
 
-    // ============================================================
     // Helpers
-    // ============================================================
     task automatic gmii_idle;
         input integer cycles;
         integer i;
@@ -111,9 +125,7 @@ module tb_mac_test;
         end
     endtask
 
-    // ============================================================
     // Monitor AXIS RX
-    // ============================================================
     always @(posedge gmii_rx_clk) begin
         if (m_axis_rx_tvalid && m_axis_rx_tready) begin
             $write("%02x ", m_axis_rx_tdata);
@@ -126,9 +138,7 @@ module tb_mac_test;
         end else m_axis_rx_tready = 1'b0;
     end
 
-    // ============================================================
     // Test sequence
-    // ============================================================
     integer i;
 
     initial begin
@@ -242,7 +252,7 @@ module tb_mac_test;
         send_gmii_frame_mem(66);
         gmii_idle(200);
 
-        $display("\nSimulation done");
+        $display("\nSimulation done OK");
         $finish;
     end
 

rtl/ethernet-udp/tests/eth_minimal/Makefile

@@ -22,6 +22,9 @@ SYN_FILES += $(sort $(shell find ../../src -type f \( -name '*.v' -o -name '*.sv
 
 XCI_FILES = $(sort $(shell find ../../src -type f -name '*.xci'))
 
+XDC_FILES += debug.xdc
+XDC_FILES += ../../../../constraints/ax7a035b.xdc
+
 program: $(PROJECT).bit
 	echo "open_hw_manager" > program.tcl
 	echo "connect_hw_server" >> program.tcl

rtl/ethernet-udp/tests/eth_minimal/axis_mac.sv

@@ -1,229 +0,0 @@
-`timescale 1 ns / 1 ns
-
-module axis_mac
-(
-    input                rst_n,
-    input                gmii_tx_clk,
-    input                gmii_rx_clk,
-    input                gmii_rx_dv,
-    input  [7:0]         gmii_rxd,
-
-    output reg           gmii_tx_en,
-    output reg [7:0]     gmii_txd,
-
-    // AXI-stream RX output (clock domain = gmii_rx_clk)
-    (* MARK_DEBUG="true" *)output reg  [7:0]    m_axis_rx_tdata,
-    (* MARK_DEBUG="true" *)output reg           m_axis_rx_tvalid,
-    input  wire          m_axis_rx_tready,
-    (* MARK_DEBUG="true" *)output reg           m_axis_rx_tlast
-);
-
-    // ----------------------------------------------------------------
-    // GMII RX input registering
-    // ----------------------------------------------------------------
-    reg        gmii_rx_dv_d0;
-    reg [7:0]  gmii_rxd_d0;
-
-    always @(posedge gmii_rx_clk or negedge rst_n) begin
-        if (!rst_n) begin
-            gmii_rx_dv_d0 <= 1'b0;
-            gmii_rxd_d0   <= 8'd0;
-        end else begin
-            gmii_rx_dv_d0 <= gmii_rx_dv;
-            gmii_rxd_d0   <= gmii_rxd;
-        end
-    end
-
-    // ----------------------------------------------------------------
-    // TX path from mac_top
-    // ----------------------------------------------------------------
-    wire       gmii_tx_en_tmp;
-    wire [7:0] gmii_txd_tmp;
-
-    always @(posedge gmii_tx_clk or negedge rst_n) begin
-        if (!rst_n) begin
-            gmii_tx_en <= 1'b0;
-            gmii_txd   <= 8'd0;
-        end else begin
-            gmii_tx_en <= gmii_tx_en_tmp;
-            gmii_txd   <= gmii_txd_tmp;
-        end
-    end
-
-    // ----------------------------------------------------------------
-    // Unused user TX path into mac_top
-    // We disable user UDP TX for now.
-    // ARP replies and ICMP replies inside mac_top still work.
-    // ----------------------------------------------------------------
-    wire       udp_ram_data_req;
-    wire       udp_tx_end;
-    wire       almost_full;
-    wire       mac_send_end;
-    wire       arp_found;
-    wire       mac_not_exist;
-
-    wire [7:0]  udp_rec_ram_rdata;
-    reg  [10:0] udp_rec_ram_read_addr;
-    wire [15:0] udp_rec_data_length;
-    wire        udp_rec_data_valid;
-
-    wire [7:0]  tx_ram_wr_data      = 8'd0;
-    wire        tx_ram_wr_en        = 1'b0;
-    wire [15:0] udp_send_data_length = 16'd0;
-    wire        udp_tx_req          = 1'b0;
-    wire        arp_request_req     = 1'b0;
-
-    mac_top mac_top0 (
-        .gmii_tx_clk               (gmii_tx_clk),
-        .gmii_rx_clk               (gmii_rx_clk),
-        .rst_n                     (rst_n),
-
-        .source_mac_addr           (48'h00_0a_35_01_fe_c0),
-        .TTL                       (8'h80),
-        .source_ip_addr            (32'hc0a80002),   // 192.168.0.2
-        .destination_ip_addr       (32'hc0a80003),   // 192.168.0.3 (не используется для user TX пока)
-        .udp_send_source_port      (16'h1f90),       // 8080
-        .udp_send_destination_port (16'h1f90),       // 8080
-
-        .ram_wr_data               (tx_ram_wr_data),
-        .ram_wr_en                 (tx_ram_wr_en),
-        .udp_ram_data_req          (udp_ram_data_req),
-        .udp_send_data_length      (udp_send_data_length),
-        .udp_tx_end                (udp_tx_end),
-        .almost_full               (almost_full),
-
-        .udp_tx_req                (udp_tx_req),
-        .arp_request_req           (arp_request_req),
-
-        .mac_send_end              (mac_send_end),
-        .mac_data_valid            (gmii_tx_en_tmp),
-        .mac_tx_data               (gmii_txd_tmp),
-
-        .rx_dv                     (gmii_rx_dv_d0),
-        .mac_rx_datain             (gmii_rxd_d0),
-
-        .udp_rec_ram_rdata         (udp_rec_ram_rdata),
-        .udp_rec_ram_read_addr     (udp_rec_ram_read_addr),
-        .udp_rec_data_length       (udp_rec_data_length),
-        .udp_rec_data_valid        (udp_rec_data_valid),
-
-        .arp_found                 (arp_found),
-        .mac_not_exist             (mac_not_exist)
-    );
-
-    // ----------------------------------------------------------------
-    // Detect "new packet ready" on udp_rec_data_valid rising edge
-    // ----------------------------------------------------------------
-    reg udp_rec_data_valid_d0;
-
-    always @(posedge gmii_rx_clk or negedge rst_n) begin
-        if (!rst_n)
-            udp_rec_data_valid_d0 <= 1'b0;
-        else
-            udp_rec_data_valid_d0 <= udp_rec_data_valid;
-    end
-
-    wire udp_pkt_done = udp_rec_data_valid & ~udp_rec_data_valid_d0;
-
-    // ----------------------------------------------------------------
-    // RX RAM -> AXI-stream bridge
-    //
-    // Assumption:
-    //   udp_rec_data_length includes 8-byte UDP header,
-    //   so payload length = udp_rec_data_length - 8
-    //
-    // This implementation is simple and safe:
-    // - start on udp_pkt_done
-    // - read bytes 0 .. payload_len-1 from RX RAM
-    // - output them on AXIS
-    //
-    // Because the BRAM read port is synchronous, this bridge may insert
-    // bubbles between bytes. For first bring-up this is fine.
-    // ----------------------------------------------------------------
-    localparam RX_IDLE  = 2'd0;
-    localparam RX_ADDR  = 2'd1;
-    localparam RX_DATA  = 2'd2;
-
-    (* MARK_DEBUG="true" *) reg [1:0]  rx_state;
-    (* MARK_DEBUG="true" *) reg [15:0] rx_payload_len;
-    (* MARK_DEBUG="true" *) reg [15:0] rx_index;
-
-    always @(posedge gmii_rx_clk or negedge rst_n) begin
-        if (!rst_n) begin
-            rx_state              <= RX_IDLE;
-            rx_payload_len        <= 16'd0;
-            rx_index              <= 16'd0;
-            udp_rec_ram_read_addr <= 11'd0;
-
-            m_axis_rx_tdata       <= 8'd0;
-            m_axis_rx_tvalid      <= 1'b0;
-            m_axis_rx_tlast       <= 1'b0;
-        end else begin
-            case (rx_state)
-                RX_IDLE: begin
-                    m_axis_rx_tvalid <= 1'b0;
-                    m_axis_rx_tlast  <= 1'b0;
-                    rx_index         <= 16'd0;
-                    udp_rec_ram_read_addr <= 11'd0;
-
-                    if (udp_pkt_done) begin
-                        // protect against pathological short values
-                        if (udp_rec_data_length > 16'd8) begin
-                            rx_payload_len        <= udp_rec_data_length - 16'd8;
-                            udp_rec_ram_read_addr <= 11'd0;   // issue read for byte 0
-                            rx_state              <= RX_ADDR;
-                        end else begin
-                            rx_payload_len <= 16'd0;
-                            rx_state       <= RX_IDLE;
-                        end
-                    end
-                end
-
-                // one cycle for synchronous BRAM read latency
-                RX_ADDR: begin
-                    m_axis_rx_tvalid <= 1'b0;
-                    m_axis_rx_tlast  <= 1'b0;
-                    rx_state         <= RX_DATA;
-                end
-
-                RX_DATA: begin
-                    // hold valid until accepted
-                    if (m_axis_rx_tvalid && !m_axis_rx_tready) begin
-                        m_axis_rx_tvalid <= m_axis_rx_tvalid;
-                        m_axis_rx_tlast  <= m_axis_rx_tlast;
-                    end else begin
-                        // present current byte from RAM
-                        m_axis_rx_tdata  <= udp_rec_ram_rdata;
-                        m_axis_rx_tvalid <= 1'b1;
-                        m_axis_rx_tlast  <= (rx_index == rx_payload_len - 1);
-
-                        if (rx_index == rx_payload_len - 1) begin
-                            // last byte accepted immediately if ready=1,
-                            // otherwise valid/last remain asserted until ready
-                            if (m_axis_rx_tready) begin
-                                m_axis_rx_tvalid <= 1'b0;
-                                m_axis_rx_tlast  <= 1'b0;
-                                rx_state         <= RX_IDLE;
-                            end
-                        end else begin
-                            if (m_axis_rx_tready) begin
-                                rx_index <= rx_index + 1'b1;
-                                udp_rec_ram_read_addr <= rx_index + 1'b1; // next byte
-                                rx_state <= RX_ADDR;
-                                m_axis_rx_tvalid <= 1'b0;
-                                m_axis_rx_tlast  <= 1'b0;
-                            end
-                        end
-                    end
-                end
-
-                default: begin
-                    rx_state         <= RX_IDLE;
-                    m_axis_rx_tvalid <= 1'b0;
-                    m_axis_rx_tlast  <= 1'b0;
-                end
-            endcase
-        end
-    end
-
-endmodule

rtl/ethernet-udp/tests/eth_minimal/debug.xdc

@@ -0,0 +1,188 @@
+# debug ILA
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 9 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {mac_test0/state[0]} {mac_test0/state[1]} {mac_test0/state[2]} {mac_test0/state[3]} {mac_test0/state[4]} {mac_test0/state[5]} {mac_test0/state[6]} {mac_test0/state[7]} {mac_test0/state[8]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 8 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {arbi_inst/rx_buffer_inst/e10_100_rxd[0]} {arbi_inst/rx_buffer_inst/e10_100_rxd[1]} {arbi_inst/rx_buffer_inst/e10_100_rxd[2]} {arbi_inst/rx_buffer_inst/e10_100_rxd[3]} {arbi_inst/rx_buffer_inst/e10_100_rxd[4]} {arbi_inst/rx_buffer_inst/e10_100_rxd[5]} {arbi_inst/rx_buffer_inst/e10_100_rxd[6]} {arbi_inst/rx_buffer_inst/e10_100_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 8 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {arbi_inst/tx_buffer_inst/tx_wdata[0]} {arbi_inst/tx_buffer_inst/tx_wdata[1]} {arbi_inst/tx_buffer_inst/tx_wdata[2]} {arbi_inst/tx_buffer_inst/tx_wdata[3]} {arbi_inst/tx_buffer_inst/tx_wdata[4]} {arbi_inst/tx_buffer_inst/tx_wdata[5]} {arbi_inst/tx_buffer_inst/tx_wdata[6]} {arbi_inst/tx_buffer_inst/tx_wdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 8 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list {arbi_inst/tx_buffer_inst/tx_rdata[0]} {arbi_inst/tx_buffer_inst/tx_rdata[1]} {arbi_inst/tx_buffer_inst/tx_rdata[2]} {arbi_inst/tx_buffer_inst/tx_rdata[3]} {arbi_inst/tx_buffer_inst/tx_rdata[4]} {arbi_inst/tx_buffer_inst/tx_rdata[5]} {arbi_inst/tx_buffer_inst/tx_rdata[6]} {arbi_inst/tx_buffer_inst/tx_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 16 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list {arbi_inst/tx_buffer_inst/tx_data_cnt[0]} {arbi_inst/tx_buffer_inst/tx_data_cnt[1]} {arbi_inst/tx_buffer_inst/tx_data_cnt[2]} {arbi_inst/tx_buffer_inst/tx_data_cnt[3]} {arbi_inst/tx_buffer_inst/tx_data_cnt[4]} {arbi_inst/tx_buffer_inst/tx_data_cnt[5]} {arbi_inst/tx_buffer_inst/tx_data_cnt[6]} {arbi_inst/tx_buffer_inst/tx_data_cnt[7]} {arbi_inst/tx_buffer_inst/tx_data_cnt[8]} {arbi_inst/tx_buffer_inst/tx_data_cnt[9]} {arbi_inst/tx_buffer_inst/tx_data_cnt[10]} {arbi_inst/tx_buffer_inst/tx_data_cnt[11]} {arbi_inst/tx_buffer_inst/tx_data_cnt[12]} {arbi_inst/tx_buffer_inst/tx_data_cnt[13]} {arbi_inst/tx_buffer_inst/tx_data_cnt[14]} {arbi_inst/tx_buffer_inst/tx_data_cnt[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 16 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp_send_data_length[0]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[1]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[2]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[3]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[4]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[5]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[6]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[7]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[8]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[9]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[10]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[11]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[12]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[13]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[14]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 12 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[0]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[1]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[2]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[3]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[4]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[5]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[6]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[7]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[8]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[9]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[10]} {mac_test0/mac_top0/mac_tx0/udp_ram_data_count[11]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe7]
+set_property port_width 8 [get_debug_ports u_ila_0/probe7]
+connect_debug_port u_ila_0/probe7 [get_nets [list {mac_test0/mac_top0/mac_tx0/ram_wr_data[0]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[1]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[2]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[3]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[4]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[5]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[6]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe8]
+set_property port_width 8 [get_debug_ports u_ila_0/probe8]
+connect_debug_port u_ila_0/probe8 [get_nets [list {mac_test0/mac_top0/mac_tx0/mac_tx_data[0]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[1]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[2]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[3]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[4]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[5]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[6]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe9]
+set_property port_width 4 [get_debug_ports u_ila_0/probe9]
+connect_debug_port u_ila_0/probe9 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/usedw[0]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[1]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[2]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[3]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe10]
+set_property port_width 6 [get_debug_ports u_ila_0/probe10]
+connect_debug_port u_ila_0/probe10 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/state[0]} {mac_test0/mac_top0/mac_tx0/udp0/state[1]} {mac_test0/mac_top0/mac_tx0/udp0/state[2]} {mac_test0/mac_top0/mac_tx0/udp0/state[3]} {mac_test0/mac_top0/mac_tx0/udp0/state[4]} {mac_test0/mac_top0/mac_tx0/udp0/state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe11]
+set_property port_width 6 [get_debug_ports u_ila_0/probe11]
+connect_debug_port u_ila_0/probe11 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/ck_state[0]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[1]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[2]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[3]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[4]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe12]
+set_property port_width 16 [get_debug_ports u_ila_0/probe12]
+connect_debug_port u_ila_0/probe12 [get_nets [list {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[0]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[1]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[2]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[3]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[4]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[5]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[6]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[7]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[8]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[9]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[10]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[11]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[12]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[13]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[14]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe13]
+set_property port_width 11 [get_debug_ports u_ila_0/probe13]
+connect_debug_port u_ila_0/probe13 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[7]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[8]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[9]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe14]
+set_property port_width 8 [get_debug_ports u_ila_0/probe14]
+connect_debug_port u_ila_0/probe14 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe15]
+set_property port_width 16 [get_debug_ports u_ila_0/probe15]
+connect_debug_port u_ila_0/probe15 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[7]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[8]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[9]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[10]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[11]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[12]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[13]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[14]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe16]
+set_property port_width 8 [get_debug_ports u_ila_0/probe16]
+connect_debug_port u_ila_0/probe16 [get_nets [list {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[0]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[1]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[2]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[3]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[4]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[5]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[6]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe17]
+set_property port_width 16 [get_debug_ports u_ila_0/probe17]
+connect_debug_port u_ila_0/probe17 [get_nets [list {mac_test0/mac_top0/mac_rx0/ip_total_data_length[0]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[1]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[2]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[3]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[4]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[5]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[6]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[7]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[8]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[9]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[10]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[11]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[12]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[13]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[14]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe18]
+set_property port_width 8 [get_debug_ports u_ila_0/probe18]
+connect_debug_port u_ila_0/probe18 [get_nets [list {mac_test0/mac_top0/mac_rx0/mac_rx_datain[0]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[1]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[2]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[3]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[4]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[5]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[6]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe19]
+set_property port_width 11 [get_debug_ports u_ila_0/probe19]
+connect_debug_port u_ila_0/probe19 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[0]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[1]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[2]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[3]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[4]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[5]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[6]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[7]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[8]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[9]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe20]
+set_property port_width 8 [get_debug_ports u_ila_0/probe20]
+connect_debug_port u_ila_0/probe20 [get_nets [list {arbi_inst/gmii_txd[0]} {arbi_inst/gmii_txd[1]} {arbi_inst/gmii_txd[2]} {arbi_inst/gmii_txd[3]} {arbi_inst/gmii_txd[4]} {arbi_inst/gmii_txd[5]} {arbi_inst/gmii_txd[6]} {arbi_inst/gmii_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe21]
+set_property port_width 8 [get_debug_ports u_ila_0/probe21]
+connect_debug_port u_ila_0/probe21 [get_nets [list {arbi_inst/gmii_rxd[0]} {arbi_inst/gmii_rxd[1]} {arbi_inst/gmii_rxd[2]} {arbi_inst/gmii_rxd[3]} {arbi_inst/gmii_rxd[4]} {arbi_inst/gmii_rxd[5]} {arbi_inst/gmii_rxd[6]} {arbi_inst/gmii_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe22]
+set_property port_width 8 [get_debug_ports u_ila_0/probe22]
+connect_debug_port u_ila_0/probe22 [get_nets [list {arbi_inst/e_txd[0]} {arbi_inst/e_txd[1]} {arbi_inst/e_txd[2]} {arbi_inst/e_txd[3]} {arbi_inst/e_txd[4]} {arbi_inst/e_txd[5]} {arbi_inst/e_txd[6]} {arbi_inst/e_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe23]
+set_property port_width 8 [get_debug_ports u_ila_0/probe23]
+connect_debug_port u_ila_0/probe23 [get_nets [list {arbi_inst/e_rxd[0]} {arbi_inst/e_rxd[1]} {arbi_inst/e_rxd[2]} {arbi_inst/e_rxd[3]} {arbi_inst/e_rxd[4]} {arbi_inst/e_rxd[5]} {arbi_inst/e_rxd[6]} {arbi_inst/e_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe24]
+set_property port_width 1 [get_debug_ports u_ila_0/probe24]
+connect_debug_port u_ila_0/probe24 [get_nets [list mac_test0/mac_top0/mac_tx0/almost_full]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe25]
+set_property port_width 1 [get_debug_ports u_ila_0/probe25]
+connect_debug_port u_ila_0/probe25 [get_nets [list arbi_inst/rx_buffer_inst/e10_100_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe26]
+set_property port_width 1 [get_debug_ports u_ila_0/probe26]
+connect_debug_port u_ila_0/probe26 [get_nets [list arbi_inst/e_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe27]
+set_property port_width 1 [get_debug_ports u_ila_0/probe27]
+connect_debug_port u_ila_0/probe27 [get_nets [list arbi_inst/e_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe28]
+set_property port_width 1 [get_debug_ports u_ila_0/probe28]
+connect_debug_port u_ila_0/probe28 [get_nets [list arbi_inst/gmii_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe29]
+set_property port_width 1 [get_debug_ports u_ila_0/probe29]
+connect_debug_port u_ila_0/probe29 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d0]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe30]
+set_property port_width 1 [get_debug_ports u_ila_0/probe30]
+connect_debug_port u_ila_0/probe30 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d1]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe31]
+set_property port_width 1 [get_debug_ports u_ila_0/probe31]
+connect_debug_port u_ila_0/probe31 [get_nets [list arbi_inst/gmii_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe32]
+set_property port_width 1 [get_debug_ports u_ila_0/probe32]
+connect_debug_port u_ila_0/probe32 [get_nets [list mac_test0/mac_top0/mac_tx0/mac_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe33]
+set_property port_width 1 [get_debug_ports u_ila_0/probe33]
+connect_debug_port u_ila_0/probe33 [get_nets [list mac_test0/mac_top0/mac_tx0/mac_send_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe34]
+set_property port_width 1 [get_debug_ports u_ila_0/probe34]
+connect_debug_port u_ila_0/probe34 [get_nets [list mac_test0/mac_top0/mac_rx0/udp0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe35]
+set_property port_width 1 [get_debug_ports u_ila_0/probe35]
+connect_debug_port u_ila_0/probe35 [get_nets [list mac_test0/mac_top0/mac_tx0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe36]
+set_property port_width 1 [get_debug_ports u_ila_0/probe36]
+connect_debug_port u_ila_0/probe36 [get_nets [list arbi_inst/tx_buffer_inst/tx_rden]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe37]
+set_property port_width 1 [get_debug_ports u_ila_0/probe37]
+connect_debug_port u_ila_0/probe37 [get_nets [list arbi_inst/tx_buffer_inst/tx_wren]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe38]
+set_property port_width 1 [get_debug_ports u_ila_0/probe38]
+connect_debug_port u_ila_0/probe38 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_ram_data_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe39]
+set_property port_width 1 [get_debug_ports u_ila_0/probe39]
+connect_debug_port u_ila_0/probe39 [get_nets [list mac_test0/mac_top0/mac_rx0/udp_rec_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe40]
+set_property port_width 1 [get_debug_ports u_ila_0/probe40]
+connect_debug_port u_ila_0/probe40 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_tx_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe41]
+set_property port_width 1 [get_debug_ports u_ila_0/probe41]
+connect_debug_port u_ila_0/probe41 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_tx_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe42]
+set_property port_width 1 [get_debug_ports u_ila_0/probe42]
+connect_debug_port u_ila_0/probe42 [get_nets [list mac_test0/mac_top0/mac_tx0/upper_data_req]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets rgmii_rxc_IBUF_BUFG]

rtl/ethernet-udp/tests/eth_minimal/ethernet_test_minimal.v

@@ -1,31 +1,3 @@
-//////////////////////////////////////////////////////////////////////////////////
-//                                                                              //
-//                                                                              //
-//  Author: lhj                                                                 //
-//                                                                              //
-//          ALINX(shanghai) Technology Co.,Ltd                                  //
-//          heijin                                                              //
-//     WEB: http://www.alinx.com/                                               //
-//     BBS: http://www.heijin.org/                                              //
-//                                                                              //
-//////////////////////////////////////////////////////////////////////////////////
-//                                                                              //
-// Copyright (c) 2017,ALINX(shanghai) Technology Co.,Ltd                        //
-//                    All rights reserved                                       //
-//                                                                              //
-// This source file may be used and distributed without restriction provided    //
-// that this copyright statement is not removed from the file and that any      //
-// derivative work contains the original copyright notice and the associated    //
-// disclaimer.                                                                  //
-//                                                                              //
-//////////////////////////////////////////////////////////////////////////////////
-
-//================================================================================
-//  Revision History:
-//  Date          By            Revision    Change Description
-//--------------------------------------------------------------------------------
-//  2019/08/19   
-//*******************************************************************************/
 module ethernet_test_minimal
 (
 input               sys_clk_p,                       //system clock positive

rtl/ethernet-udp/tests/eth_minimal/ethernet_test_minimal.xdc

@@ -49,3 +49,193 @@ set_property PACKAGE_PIN R19 [get_ports rgmii_rxctl]
 set_property PACKAGE_PIN P15 [get_ports rgmii_txc]
 set_property PACKAGE_PIN N17 [get_ports rgmii_txctl]
 
+
+
+
+
+create_debug_core u_ila_0 ila
+set_property ALL_PROBE_SAME_MU true [get_debug_cores u_ila_0]
+set_property ALL_PROBE_SAME_MU_CNT 1 [get_debug_cores u_ila_0]
+set_property C_ADV_TRIGGER false [get_debug_cores u_ila_0]
+set_property C_DATA_DEPTH 1024 [get_debug_cores u_ila_0]
+set_property C_EN_STRG_QUAL false [get_debug_cores u_ila_0]
+set_property C_INPUT_PIPE_STAGES 0 [get_debug_cores u_ila_0]
+set_property C_TRIGIN_EN false [get_debug_cores u_ila_0]
+set_property C_TRIGOUT_EN false [get_debug_cores u_ila_0]
+set_property port_width 1 [get_debug_ports u_ila_0/clk]
+connect_debug_port u_ila_0/clk [get_nets [list rgmii_rxc_IBUF_BUFG]]
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe0]
+set_property port_width 9 [get_debug_ports u_ila_0/probe0]
+connect_debug_port u_ila_0/probe0 [get_nets [list {mac_test0/state[0]} {mac_test0/state[1]} {mac_test0/state[2]} {mac_test0/state[3]} {mac_test0/state[4]} {mac_test0/state[5]} {mac_test0/state[6]} {mac_test0/state[7]} {mac_test0/state[8]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe1]
+set_property port_width 8 [get_debug_ports u_ila_0/probe1]
+connect_debug_port u_ila_0/probe1 [get_nets [list {arbi_inst/rx_buffer_inst/e10_100_rxd[0]} {arbi_inst/rx_buffer_inst/e10_100_rxd[1]} {arbi_inst/rx_buffer_inst/e10_100_rxd[2]} {arbi_inst/rx_buffer_inst/e10_100_rxd[3]} {arbi_inst/rx_buffer_inst/e10_100_rxd[4]} {arbi_inst/rx_buffer_inst/e10_100_rxd[5]} {arbi_inst/rx_buffer_inst/e10_100_rxd[6]} {arbi_inst/rx_buffer_inst/e10_100_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe2]
+set_property port_width 8 [get_debug_ports u_ila_0/probe2]
+connect_debug_port u_ila_0/probe2 [get_nets [list {arbi_inst/gmii_txd[0]} {arbi_inst/gmii_txd[1]} {arbi_inst/gmii_txd[2]} {arbi_inst/gmii_txd[3]} {arbi_inst/gmii_txd[4]} {arbi_inst/gmii_txd[5]} {arbi_inst/gmii_txd[6]} {arbi_inst/gmii_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe3]
+set_property port_width 8 [get_debug_ports u_ila_0/probe3]
+connect_debug_port u_ila_0/probe3 [get_nets [list {arbi_inst/gmii_rxd[0]} {arbi_inst/gmii_rxd[1]} {arbi_inst/gmii_rxd[2]} {arbi_inst/gmii_rxd[3]} {arbi_inst/gmii_rxd[4]} {arbi_inst/gmii_rxd[5]} {arbi_inst/gmii_rxd[6]} {arbi_inst/gmii_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe4]
+set_property port_width 8 [get_debug_ports u_ila_0/probe4]
+connect_debug_port u_ila_0/probe4 [get_nets [list {arbi_inst/e_txd[0]} {arbi_inst/e_txd[1]} {arbi_inst/e_txd[2]} {arbi_inst/e_txd[3]} {arbi_inst/e_txd[4]} {arbi_inst/e_txd[5]} {arbi_inst/e_txd[6]} {arbi_inst/e_txd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe5]
+set_property port_width 8 [get_debug_ports u_ila_0/probe5]
+connect_debug_port u_ila_0/probe5 [get_nets [list {arbi_inst/e_rxd[0]} {arbi_inst/e_rxd[1]} {arbi_inst/e_rxd[2]} {arbi_inst/e_rxd[3]} {arbi_inst/e_rxd[4]} {arbi_inst/e_rxd[5]} {arbi_inst/e_rxd[6]} {arbi_inst/e_rxd[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe6]
+set_property port_width 8 [get_debug_ports u_ila_0/probe6]
+connect_debug_port u_ila_0/probe6 [get_nets [list {arbi_inst/tx_buffer_inst/tx_wdata[0]} {arbi_inst/tx_buffer_inst/tx_wdata[1]} {arbi_inst/tx_buffer_inst/tx_wdata[2]} {arbi_inst/tx_buffer_inst/tx_wdata[3]} {arbi_inst/tx_buffer_inst/tx_wdata[4]} {arbi_inst/tx_buffer_inst/tx_wdata[5]} {arbi_inst/tx_buffer_inst/tx_wdata[6]} {arbi_inst/tx_buffer_inst/tx_wdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe7]
+set_property port_width 8 [get_debug_ports u_ila_0/probe7]
+connect_debug_port u_ila_0/probe7 [get_nets [list {arbi_inst/tx_buffer_inst/tx_rdata[0]} {arbi_inst/tx_buffer_inst/tx_rdata[1]} {arbi_inst/tx_buffer_inst/tx_rdata[2]} {arbi_inst/tx_buffer_inst/tx_rdata[3]} {arbi_inst/tx_buffer_inst/tx_rdata[4]} {arbi_inst/tx_buffer_inst/tx_rdata[5]} {arbi_inst/tx_buffer_inst/tx_rdata[6]} {arbi_inst/tx_buffer_inst/tx_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe8]
+set_property port_width 16 [get_debug_ports u_ila_0/probe8]
+connect_debug_port u_ila_0/probe8 [get_nets [list {arbi_inst/tx_buffer_inst/tx_data_cnt[0]} {arbi_inst/tx_buffer_inst/tx_data_cnt[1]} {arbi_inst/tx_buffer_inst/tx_data_cnt[2]} {arbi_inst/tx_buffer_inst/tx_data_cnt[3]} {arbi_inst/tx_buffer_inst/tx_data_cnt[4]} {arbi_inst/tx_buffer_inst/tx_data_cnt[5]} {arbi_inst/tx_buffer_inst/tx_data_cnt[6]} {arbi_inst/tx_buffer_inst/tx_data_cnt[7]} {arbi_inst/tx_buffer_inst/tx_data_cnt[8]} {arbi_inst/tx_buffer_inst/tx_data_cnt[9]} {arbi_inst/tx_buffer_inst/tx_data_cnt[10]} {arbi_inst/tx_buffer_inst/tx_data_cnt[11]} {arbi_inst/tx_buffer_inst/tx_data_cnt[12]} {arbi_inst/tx_buffer_inst/tx_data_cnt[13]} {arbi_inst/tx_buffer_inst/tx_data_cnt[14]} {arbi_inst/tx_buffer_inst/tx_data_cnt[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe9]
+set_property port_width 6 [get_debug_ports u_ila_0/probe9]
+connect_debug_port u_ila_0/probe9 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/ck_state[0]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[1]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[2]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[3]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[4]} {mac_test0/mac_top0/mac_tx0/udp0/ck_state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe10]
+set_property port_width 16 [get_debug_ports u_ila_0/probe10]
+connect_debug_port u_ila_0/probe10 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp_send_data_length[0]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[1]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[2]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[3]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[4]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[5]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[6]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[7]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[8]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[9]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[10]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[11]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[12]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[13]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[14]} {mac_test0/mac_top0/mac_tx0/udp_send_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe11]
+set_property port_width 8 [get_debug_ports u_ila_0/probe11]
+connect_debug_port u_ila_0/probe11 [get_nets [list {mac_test0/mac_top0/mac_tx0/ram_wr_data[0]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[1]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[2]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[3]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[4]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[5]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[6]} {mac_test0/mac_top0/mac_tx0/ram_wr_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe12]
+set_property port_width 8 [get_debug_ports u_ila_0/probe12]
+connect_debug_port u_ila_0/probe12 [get_nets [list {mac_test0/mac_top0/mac_tx0/mac_tx_data[0]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[1]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[2]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[3]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[4]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[5]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[6]} {mac_test0/mac_top0/mac_tx0/mac_tx_data[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe13]
+set_property port_width 4 [get_debug_ports u_ila_0/probe13]
+connect_debug_port u_ila_0/probe13 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/usedw[0]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[1]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[2]} {mac_test0/mac_top0/mac_tx0/udp0/usedw[3]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe14]
+set_property port_width 6 [get_debug_ports u_ila_0/probe14]
+connect_debug_port u_ila_0/probe14 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/state[0]} {mac_test0/mac_top0/mac_tx0/udp0/state[1]} {mac_test0/mac_top0/mac_tx0/udp0/state[2]} {mac_test0/mac_top0/mac_tx0/udp0/state[3]} {mac_test0/mac_top0/mac_tx0/udp0/state[4]} {mac_test0/mac_top0/mac_tx0/udp0/state[5]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe15]
+set_property port_width 12 [get_debug_ports u_ila_0/probe15]
+connect_debug_port u_ila_0/probe15 [get_nets [list {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[0]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[1]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[2]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[3]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[4]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[5]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[6]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[7]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[8]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[9]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[10]} {mac_test0/mac_top0/mac_tx0/udp0/dbg_fifo_count[11]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe16]
+set_property port_width 16 [get_debug_ports u_ila_0/probe16]
+connect_debug_port u_ila_0/probe16 [get_nets [list {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[0]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[1]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[2]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[3]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[4]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[5]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[6]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[7]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[8]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[9]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[10]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[11]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[12]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[13]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[14]} {mac_test0/mac_top0/mac_rx0/upper_layer_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe17]
+set_property port_width 11 [get_debug_ports u_ila_0/probe17]
+connect_debug_port u_ila_0/probe17 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[7]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[8]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[9]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_read_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe18]
+set_property port_width 8 [get_debug_ports u_ila_0/probe18]
+connect_debug_port u_ila_0/probe18 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_ram_rdata[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe19]
+set_property port_width 16 [get_debug_ports u_ila_0/probe19]
+connect_debug_port u_ila_0/probe19 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[0]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[1]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[2]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[3]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[4]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[5]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[6]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[7]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[8]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[9]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[10]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[11]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[12]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[13]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[14]} {mac_test0/mac_top0/mac_rx0/udp_rec_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe20]
+set_property port_width 8 [get_debug_ports u_ila_0/probe20]
+connect_debug_port u_ila_0/probe20 [get_nets [list {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[0]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[1]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[2]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[3]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[4]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[5]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[6]} {mac_test0/mac_top0/mac_rx0/mac_rx_dataout[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe21]
+set_property port_width 16 [get_debug_ports u_ila_0/probe21]
+connect_debug_port u_ila_0/probe21 [get_nets [list {mac_test0/mac_top0/mac_rx0/ip_total_data_length[0]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[1]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[2]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[3]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[4]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[5]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[6]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[7]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[8]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[9]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[10]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[11]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[12]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[13]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[14]} {mac_test0/mac_top0/mac_rx0/ip_total_data_length[15]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe22]
+set_property port_width 8 [get_debug_ports u_ila_0/probe22]
+connect_debug_port u_ila_0/probe22 [get_nets [list {mac_test0/mac_top0/mac_rx0/mac_rx_datain[0]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[1]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[2]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[3]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[4]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[5]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[6]} {mac_test0/mac_top0/mac_rx0/mac_rx_datain[7]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe23]
+set_property port_width 11 [get_debug_ports u_ila_0/probe23]
+connect_debug_port u_ila_0/probe23 [get_nets [list {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[0]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[1]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[2]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[3]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[4]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[5]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[6]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[7]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[8]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[9]} {mac_test0/mac_top0/mac_rx0/udp0/ram_write_addr[10]}]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe24]
+set_property port_width 1 [get_debug_ports u_ila_0/probe24]
+connect_debug_port u_ila_0/probe24 [get_nets [list mac_test0/mac_top0/mac_tx0/almost_full]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe25]
+set_property port_width 1 [get_debug_ports u_ila_0/probe25]
+connect_debug_port u_ila_0/probe25 [get_nets [list arbi_inst/rx_buffer_inst/e10_100_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe26]
+set_property port_width 1 [get_debug_ports u_ila_0/probe26]
+connect_debug_port u_ila_0/probe26 [get_nets [list arbi_inst/e_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe27]
+set_property port_width 1 [get_debug_ports u_ila_0/probe27]
+connect_debug_port u_ila_0/probe27 [get_nets [list arbi_inst/e_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe28]
+set_property port_width 1 [get_debug_ports u_ila_0/probe28]
+connect_debug_port u_ila_0/probe28 [get_nets [list arbi_inst/gmii_rx_dv]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe29]
+set_property port_width 1 [get_debug_ports u_ila_0/probe29]
+connect_debug_port u_ila_0/probe29 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d0]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe30]
+set_property port_width 1 [get_debug_ports u_ila_0/probe30]
+connect_debug_port u_ila_0/probe30 [get_nets [list arbi_inst/rx_buffer_inst/gmii_rx_dv_d1]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe31]
+set_property port_width 1 [get_debug_ports u_ila_0/probe31]
+connect_debug_port u_ila_0/probe31 [get_nets [list arbi_inst/gmii_tx_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe32]
+set_property port_width 1 [get_debug_ports u_ila_0/probe32]
+connect_debug_port u_ila_0/probe32 [get_nets [list mac_test0/mac_top0/mac_tx0/mac_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe33]
+set_property port_width 1 [get_debug_ports u_ila_0/probe33]
+connect_debug_port u_ila_0/probe33 [get_nets [list mac_test0/mac_top0/mac_tx0/mac_send_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe34]
+set_property port_width 1 [get_debug_ports u_ila_0/probe34]
+connect_debug_port u_ila_0/probe34 [get_nets [list mac_test0/mac_top0/mac_tx0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe35]
+set_property port_width 1 [get_debug_ports u_ila_0/probe35]
+connect_debug_port u_ila_0/probe35 [get_nets [list mac_test0/mac_top0/mac_rx0/udp0/ram_wr_en]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe36]
+set_property port_width 1 [get_debug_ports u_ila_0/probe36]
+connect_debug_port u_ila_0/probe36 [get_nets [list arbi_inst/tx_buffer_inst/tx_rden]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe37]
+set_property port_width 1 [get_debug_ports u_ila_0/probe37]
+connect_debug_port u_ila_0/probe37 [get_nets [list arbi_inst/tx_buffer_inst/tx_wren]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe38]
+set_property port_width 1 [get_debug_ports u_ila_0/probe38]
+connect_debug_port u_ila_0/probe38 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_ram_data_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe39]
+set_property port_width 1 [get_debug_ports u_ila_0/probe39]
+connect_debug_port u_ila_0/probe39 [get_nets [list mac_test0/mac_top0/mac_rx0/udp_rec_data_valid]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe40]
+set_property port_width 1 [get_debug_ports u_ila_0/probe40]
+connect_debug_port u_ila_0/probe40 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_tx_end]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe41]
+set_property port_width 1 [get_debug_ports u_ila_0/probe41]
+connect_debug_port u_ila_0/probe41 [get_nets [list mac_test0/mac_top0/mac_tx0/udp_tx_req]]
+create_debug_port u_ila_0 probe
+set_property PROBE_TYPE DATA_AND_TRIGGER [get_debug_ports u_ila_0/probe42]
+set_property port_width 1 [get_debug_ports u_ila_0/probe42]
+connect_debug_port u_ila_0/probe42 [get_nets [list mac_test0/mac_top0/mac_tx0/upper_data_req]]
+set_property C_CLK_INPUT_FREQ_HZ 300000000 [get_debug_cores dbg_hub]
+set_property C_ENABLE_CLK_DIVIDER false [get_debug_cores dbg_hub]
+set_property C_USER_SCAN_CHAIN 1 [get_debug_cores dbg_hub]
+connect_debug_port dbg_hub/clk [get_nets rgmii_rxc_IBUF_BUFG]

rtl/generator/src/generator.sv

@@ -0,0 +1,103 @@
+`timescale 1ns / 1ps
+
+
+module generator
+#(
+    parameter DATA_WIDTH = 14
+    )
+(
+    input clk_in,
+    input rst,
+    input start,
+    input [31:0]           pulse_width,
+    input [31:0]           pulse_period,
+    input [DATA_WIDTH-1:0] pulse_height,
+    input [15:0]           pulse_num,
+    
+    output pulse,
+    output[DATA_WIDTH-1:0] pulse_height_out
+    
+    );
+    
+    logic [DATA_WIDTH-1:0] pulse_height_reg, pulse_height_out_reg;
+    logic pulse_reg;
+    
+    logic [31:0] pulse_width_reg, pulse_period_reg;
+    logic [15:0] pulse_num_reg;
+    
+    logic enable;
+    logic [15:0] cnt_pulse_num;
+    logic [31:0] cnt_period;
+    
+    logic start_d;
+
+    always @(posedge clk_in) begin
+        start_d <= start;
+    end
+
+    wire start_pulse = start & ~start_d;
+
+    
+    always @(posedge clk_in) begin
+        if (rst) begin
+            pulse_reg <= '0;
+            pulse_height_reg <= 0;
+            pulse_height_out_reg <= '0;
+            
+            pulse_width_reg <= '0;
+            pulse_period_reg <= '0;
+            pulse_num_reg <= '0;
+            enable <= 0;
+            cnt_pulse_num <= '0;
+            cnt_period <= '0;
+        end else begin
+            if (start) begin
+                enable <= 1'b1;
+//                pulse_width_reg <= pulse_width;
+//                pulse_period_reg <= pulse_period;
+//                pulse_num_reg <= pulse_num;
+//                pulse_height_reg <= pulse_height;
+                
+                cnt_pulse_num <= '0;
+                cnt_period <= '0;
+            end
+            if (enable) begin
+                pulse_reg <= 1;
+                
+                pulse_width_reg <= pulse_width;
+                pulse_period_reg <= pulse_period;
+                pulse_num_reg <= pulse_num;
+                pulse_height_reg <= pulse_height;
+                
+                if (pulse_reg) begin
+                
+                if (cnt_period < pulse_width_reg) begin
+                    pulse_height_out_reg <= pulse_height_reg;
+                end else begin
+                    pulse_height_out_reg <= '0;
+                end
+                if (cnt_period == pulse_period_reg - 1) begin
+                    cnt_period <= 0;
+                    if (cnt_pulse_num == pulse_num_reg - 1) begin
+                        enable <= 0;
+                        pulse_reg <= 0;
+                    end else begin
+                        cnt_pulse_num <= cnt_pulse_num + 1;
+                    end
+                end else begin
+                    cnt_period <= cnt_period + 1;
+                end
+                
+                end
+            end
+        end
+    end
+
+     OBUF OBUF_pulse_clk (
+        .I(clk_in),
+        .O(pulse)
+    );
+    
+    assign pulse_height_out = pulse_height_out_reg;
+    
+endmodule

rtl/generator/tests/generator_tb.sv

@@ -0,0 +1,105 @@
+`timescale 1ns / 1ps
+
+module generator_tb;
+
+    parameter DATA_WIDTH = 14;
+    parameter CLK_PERIOD = 16;
+
+    logic clk;
+    logic rst;
+    logic start;
+
+    logic [31:0] pulse_width;
+    logic [31:0] pulse_period;
+    logic [DATA_WIDTH-1:0] pulse_height;
+    logic [15:0] pulse_num;
+
+    logic pulse;
+    logic [DATA_WIDTH-1:0] pulse_height_out;
+
+    // DUT
+    generator #(
+        .DATA_WIDTH(DATA_WIDTH)
+    ) dut (
+        .clk_in(clk),
+        .rst(rst),
+        .start(start),
+        .pulse_width(pulse_width),
+        .pulse_period(pulse_period),
+        .pulse_height(pulse_height),
+        .pulse_num(pulse_num),
+        .pulse(pulse),
+        .pulse_height_out(pulse_height_out)
+    );
+
+    // Clock
+    initial begin
+        clk = 0;
+        forever #(CLK_PERIOD/2) clk = ~clk;
+    end
+
+    initial begin
+        $display("\n=== GENERATOR TEST ===\n");
+
+        rst = 1;
+        start = 0;
+
+        pulse_width  = 0;
+        pulse_period = 0;
+        pulse_height = 0;
+        pulse_num    = 0;
+
+        repeat(5) @(posedge clk);
+        rst = 0;
+
+        // --- Test 1 ---
+        // 3 clk 1, 5 clk 0,  4 pulses
+       repeat(2) @(posedge clk);
+        pulse_width  = 3;
+        pulse_period = 8;
+        pulse_num    = 4;
+        pulse_height = 14'h3FF;
+        start = 1;
+
+       repeat(1) @(posedge clk);
+        start = 0;
+
+        repeat(50) @(posedge clk);
+
+        // --- Test 2 ---
+        $display("\n--- SECOND RUN ---\n");
+
+        @(posedge clk);
+        pulse_width  = 2;
+        pulse_period = 5;
+        pulse_num    = 3;
+        pulse_height = 14'h155;
+        start = 1;
+
+        @(posedge clk);
+        start = 0;
+
+        repeat(40) @(posedge clk);
+        
+         pulse_width  = 3;
+        pulse_period = 8;
+        pulse_num    = 4;
+        pulse_height = 14'h3FF;
+        start = 1;
+
+       repeat(1) @(posedge clk);
+        start = 0;
+
+        repeat(50) @(posedge clk);
+
+        $display("\n=== TEST FINISHED ===");
+        $finish;
+    end
+
+    // Display
+    always @(posedge clk) begin
+        $display("t=%0t | pulse=%0b | height=%h",
+                  $time, pulse, pulse_height_out);
+    end
+
+endmodule

rtl/sampler/src/sampler.sv

@@ -0,0 +1,72 @@
+`timescale 1ns / 1ps
+
+
+
+module sampler
+#(
+    parameter DATA_WIDTH = 12,
+    parameter PACK_FACTOR = 3,
+    parameter PROCESS_MODE = 1
+    )
+(
+    input clk_in,
+    input rst,
+    input [DATA_WIDTH-1:0] data_in,
+    input out_of_range,
+
+    output logic [DATA_WIDTH*PACK_FACTOR-1:0]  m_axis_tdata,
+    output logic                              m_axis_tvalid
+    );
+    logic [DATA_WIDTH-1:0] data_converted;
+    logic out_of_range_reg;
+
+    always @( posedge clk_in) begin
+        if (rst) begin
+            data_converted <= '0;
+        end else begin
+            out_of_range_reg <= out_of_range;
+            if (PROCESS_MODE) begin
+                if (data_in == 12'b100000000000) begin
+                    data_converted <= data_in;
+                end else begin
+                    data_converted <= data_in[DATA_WIDTH-1]  ? {1'b1, (~data_in[DATA_WIDTH-2:0] + 1'b1)} : data_in; 
+                    
+                end
+            end else begin
+                data_converted <= data_in; 
+            end
+        end
+    end 
+    
+         
+    logic [DATA_WIDTH*PACK_FACTOR-1:0] buffer;
+    logic buffer_ready;
+
+    logic [$clog2(PACK_FACTOR):0] cnt;
+    
+    always @(posedge clk_in) begin
+        if (rst) begin
+            buffer <= '0;
+            cnt <= -1; //
+            buffer_ready <= 0;
+        end
+        else begin
+            buffer_ready <= 0;
+            if (!out_of_range_reg) begin
+                buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+                if (cnt == PACK_FACTOR-1) begin
+                    cnt <= 0;
+                    buffer_ready <= 1;
+                    buffer <= {buffer[DATA_WIDTH*(PACK_FACTOR-1)-1:0], data_converted};
+                end
+                else begin
+                    cnt <= cnt + 1;
+                end
+            end
+        end
+    end
+    
+    assign m_axis_tdata = buffer;
+    assign m_axis_tvalid = buffer_ready;
+    
+endmodule

rtl/sampler/tests/sampler_tb_advanced.sv

@@ -0,0 +1,120 @@
+`timescale 1ns / 1ps
+
+module sampler_tb;
+
+    parameter DATA_WIDTH = 12;
+    parameter PACK_FACTOR = 3;
+    parameter PROCESS_MODE = 1;
+    parameter CLK_PERIOD = 15.3846;  // 65 MHz
+
+    logic clk;
+    logic rst;
+    logic [DATA_WIDTH-1:0] data_in;
+    logic out_of_range;
+    logic [DATA_WIDTH*PACK_FACTOR-1:0] m_axis_tdata;
+    logic m_axis_tvalid;
+
+    sampler #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .PACK_FACTOR(PACK_FACTOR),
+        .PROCESS_MODE(PROCESS_MODE)
+    ) dut (
+        .clk_in(clk),
+        .rst(rst),
+        .data_in(data_in),
+        .out_of_range(out_of_range),
+        .m_axis_tdata(m_axis_tdata),
+        .m_axis_tvalid(m_axis_tvalid)
+    );
+
+    initial begin
+        clk = 0;
+        forever #(CLK_PERIOD/2) clk = ~clk;
+    end
+
+    task send(input [DATA_WIDTH-1:0] word, input bit oor);
+        @(posedge clk);
+        data_in <= word;
+        out_of_range <= oor;
+        $display("Send: %h (%0d) OOR=%b", word, word, oor);
+    endtask
+
+    initial begin
+        $display("\n=== SAMPLER TEST (MODE=%0d) ===\n", PROCESS_MODE);
+        
+        // Reset
+        rst = 1;
+        out_of_range = 0;
+        data_in = 0;
+//        send(12'h001, 0);
+        repeat(5) @(posedge clk);
+        rst = 0;
+        send(12'h001, 0);
+        repeat(1) @(posedge clk);
+        
+        // 1. Positive
+        $display("\n--- Positive numbers ---");
+//        send(12'h001, 0);
+        send(12'h002, 0);
+        send(12'h003, 0);
+        
+        send(12'h004, 0);
+        send(12'h005, 0);
+        send(12'h806, 0);
+        
+        // 2. Negative
+        $display("\n--- Negative numbers ---");
+        send(12'hFFF, 0);  // -1
+        send(12'hFFE, 0);  // -2
+        send(12'hFFD, 0);  // -3
+        
+        send(12'h800, 0);  // -2048
+        send(12'h801, 0);  // -2047
+        send(12'h802, 0);  // -2046
+        
+        // 3. Boundary
+        $display("\n--- Boundary values ---");
+        send(12'h000, 0);  // 0
+        send(12'h001, 0);  // 1
+        send(12'h7FF, 0);  // 2047 (max positive)
+        
+        send(12'h7FE, 0);  // 2046
+        send(12'h800, 0);  // -2048 (min negative)
+        send(12'hFFF, 0);  // -1
+        
+        // 4. Out of range tests
+        $display("\n--- Out of range tests ---");
+        
+
+        send(12'h00A, 0);
+        send(12'h00B, 1);  // 
+        send(12'h00C, 0);
+        send(12'h00D, 0);
+        send(12'h00E, 0);
+        send(12'h00F, 0);  
+        
+        send(12'h010, 0);
+        send(12'h011, 0);
+        send(12'h012, 1);  // 
+        
+        send(12'h013, 0);
+        send(12'h014, 0);
+        send(12'h015, 0); 
+        
+        repeat(10) @(posedge clk);
+        $display("\n=== TEST FINISHED ===");
+        $finish;
+    end
+
+    // Results
+    always @(posedge clk) begin
+        if (m_axis_tvalid) begin
+            $display("\n>>> PACKET RECEIVED at %0t ns:", $time);
+            $display("    Full: %h", m_axis_tdata);
+            $display("    Word0: %h", m_axis_tdata[11:0]);
+            $display("    Word1: %h", m_axis_tdata[23:12]);
+            $display("    Word2: %h\n", m_axis_tdata[35:24]);
+        end
+    end
+
+endmodule

rtl/sampler/tests/sampler_tb_basic.sv

@@ -0,0 +1,67 @@
+`timescale 1ns / 1ps
+
+module sampler_tb;
+
+    parameter DATA_WIDTH = 12;
+    parameter PACK_FACTOR = 3;
+    parameter PROCESS_MODE = 0;
+    
+    parameter CLK_PERIOD = 15.3846; 
+
+    logic clk;
+    logic rst;
+    logic [DATA_WIDTH-1:0] data_in;
+    logic out_of_range;
+
+    logic [DATA_WIDTH*PACK_FACTOR-1:0] m_axis_tdata;
+    logic m_axis_tvalid;
+
+    // DUT
+    sampler #(
+        .DATA_WIDTH(DATA_WIDTH),
+        .PACK_FACTOR(PACK_FACTOR),
+        .PROCESS_MODE(PROCESS_MODE)
+    ) dut (
+        .clk_in(clk),
+        .rst(rst),
+        .data_in(data_in),
+        .out_of_range(out_of_range),
+        .m_axis_tdata(m_axis_tdata),
+        .m_axis_tvalid(m_axis_tvalid)
+    );
+
+    // clock
+     initial begin
+        clk = 0;
+        forever #(CLK_PERIOD/2) clk = ~clk;
+    end
+
+    integer i;
+
+    initial begin
+        clk = 0;
+        rst = 1;
+        data_in = 0;
+        out_of_range = 0;
+
+        #20;
+        rst = 0;
+        repeat(5) @(posedge clk);
+
+        for (i = 1; i < 20; i++) begin
+            @(posedge clk);
+
+            data_in <= i;
+        end
+
+        #50;
+        $finish;
+    end
+
+    always @(posedge clk) begin
+        if (m_axis_tvalid) begin
+            $display("TIME=%0t PACKED DATA = %h", $time, m_axis_tdata);
+        end
+    end
+
+endmodule

scripts/vivado.mk

@@ -37,7 +37,7 @@
 ###################################################################
 
 # phony targets
-.PHONY: fpga vivado tmpclean clean distclean
+.PHONY: fpga vivado sim sim-gui simclean tmpclean clean distclean
 
 # prevent make from deleting intermediate files and reports
 .PRECIOUS: %.xpr %.bit %.bin %.ltx %.xsa %.mcs %.prm
@@ -46,7 +46,7 @@
 
 FPGA_TOP ?= $(FPGA_TOP)
 PROJECT ?= $(FPGA_TOP)
-XDC_FILES ?= $(PROJECT).xdc
+# XDC_FILES ?= $(PROJECT).xdc
 
 # handle file list files
 process_f_file = $(call process_f_files,$(addprefix $(dir $1),$(shell cat $1)))
@@ -55,6 +55,14 @@ uniq_base = $(if $1,$(call uniq_base,$(foreach f,$1,$(if $(filter-out $(notdir $
 SYN_FILES := $(call uniq_base,$(call process_f_files,$(SYN_FILES)))
 INC_FILES := $(call uniq_base,$(call process_f_files,$(INC_FILES)))
 
+# simulation parameters
+SIM_TOP ?= $(FPGA_TOP)_tb
+TB_FILES ?=
+SIM_FILES ?= $(SYN_FILES) $(TB_FILES)
+SIM_DEFS ?= $(DEFS)
+SIM_RUNTIME ?= all
+
+
 ###################################################################
 # Main Targets
 #
@@ -102,6 +110,13 @@ create_project.tcl: Makefile $(XCI_FILES) $(IP_TCL_FILES)
 	for x in $(XCI_FILES); do echo "import_ip $$x" >> $@; done
 	for x in $(IP_TCL_FILES); do echo "source $$x" >> $@; done
 	for x in $(CONFIG_TCL_FILES); do echo "source $$x" >> $@; done
+	if [ -n "$(TB_FILES)" ]; then \
+		echo "add_files -fileset sim_1 defines.v $(TB_FILES)" >> $@; \
+		echo "set_property top $(SIM_TOP) [get_filesets sim_1]" >> $@; \
+		echo "set_property top_lib xil_defaultlib [get_filesets sim_1]" >> $@; \
+	fi
+	echo "update_compile_order -fileset sources_1" >> $@
+	echo "update_compile_order -fileset sim_1" >> $@
 
 # source config TCL scripts if any source file has changed
 update_config.tcl: $(CONFIG_TCL_FILES) $(SYN_FILES) $(INC_FILES) $(XDC_FILES)
@@ -149,3 +164,24 @@ $(PROJECT).bit $(PROJECT).bin $(PROJECT).ltx $(PROJECT).xsa: $(PROJECT).runs/imp
 	cp -pv $(PROJECT).runs/impl_1/$(PROJECT).bin rev/$(PROJECT)_rev$$COUNT.bin; \
 	if [ -e $(PROJECT).runs/impl_1/$(PROJECT).ltx ]; then cp -pv $(PROJECT).runs/impl_1/$(PROJECT).ltx rev/$(PROJECT)_rev$$COUNT.ltx; fi; \
 	if [ -e $(PROJECT).xsa ]; then cp -pv $(PROJECT).xsa rev/$(PROJECT)_rev$$COUNT.xsa; fi
+
+###################################################################
+# Simulation targets
+###################################################################
+
+gen_ip:
+	echo "open_project $(PROJECT).xpr" > gen_ip.tcl
+	echo "generate_target all [get_ips *]" >> gen_ip.tcl
+	vivado -mode batch -source gen_ip.tcl
+
+
+sim: $(PROJECT).xpr gen_ip
+	echo "open_project $(PROJECT).xpr" > run_sim.tcl
+	echo "update_compile_order -fileset sources_1" >> run_sim.tcl
+	echo "update_compile_order -fileset sim_1" >> run_sim.tcl
+	echo "launch_simulation" >> run_sim.tcl
+	vivado -mode batch -source run_sim.tcl
+
+simclean:
+	-rm -rf xsim.dir *.wdb *.pb *.jou *.log *.vcd *.ltx
+	-rm -f defines_sim.v

software/console.py

@@ -0,0 +1,123 @@
+import argparse
+import socket
+
+
+def run_debug(args, sock):
+    """Debug run: send fixed values to test eth+ctrl on fpga."""
+    print(f"DEBUG MODE: ip={args.ip} send_port={args.send_port}")
+
+    dest = (args.ip, args.send_port)
+
+    # reset
+    sock.sendto(0x0f00.to_bytes(2), dest)
+    print("Sent soft_reset!")
+
+    # config data
+    sock.sendto(format_ctrl_data(0x12345678, 0x9abcdef0,
+                0x0bea, 0xdead, dac_bits=args.dac_bits), dest)
+    print("Config data sent!")
+
+    sock.sendto(0xf000.to_bytes(2), dest)
+    print("Sent start!")
+
+
+def format_ctrl_data(pulse_width: int, pulse_period: int,
+                     pulse_height: int, pulse_num: int, dac_bits: int = 16) -> bytes:
+    """Format data packet for set_data command."""
+    output = bytearray()
+
+    output += 0b10001000.to_bytes(1, 'little')
+
+    # no negative please
+    assert pulse_width > 0, "pulse_width should be positive"
+    assert pulse_period > 0, "pulse_period should be positive"
+    assert pulse_num > 0, "pulse_num should be positive"
+    assert pulse_height > 0, "pulse_height should be positive"
+
+    # overflow check
+    assert pulse_width < 2**32-1, "pulse_width too high"
+    assert pulse_period < 2**32-1, "pulse_period too high"
+    assert pulse_num < 2**16-1, "pulse_num too high"
+    assert pulse_height < 2**dac_bits-1, "pulse_height too high"
+
+    output += pulse_width.to_bytes(4, 'little')
+    output += pulse_period.to_bytes(4, 'little')
+    output += pulse_num.to_bytes(2, 'little')
+    output += pulse_height.to_bytes(2, 'little')
+
+    assert len(output) == 13, "Config data should be 96 bits + 8 bit header"
+    return output
+
+
+def verify_args(args):
+    """check args are non zero and in bound, request from user if needed"""
+    if args.pulse_width == 0:
+        args.pulse_width = int(input("pulse_width: "))
+
+    if args.pulse_period == 0:
+        args.pulse_period = int(input("pulse_period: "))
+
+    if args.pulse_num == 0:
+        args.pulse_num = int(input("pulse_num: "))
+
+    if args.pulse_height == 0:
+        args.pulse_height = int(input("pulse_height: "))
+
+
+def run(args, sock):
+    dest = (args.ip, args.send_port)
+
+    # reset
+    sock.sendto(0x0f00.to_bytes(2), dest)
+
+    # config data
+    sock.sendto(format_ctrl_data(args.pulse_width,
+                                 args.pulse_period,
+                                 args.pulse_height,
+                                 args.pulse_num,
+                                 dac_bits=args.dac_bits), dest)
+
+    sock.sendto(0xf000.to_bytes(2), dest)
+    print("Sent start!")
+
+
+def main():
+    parser = argparse.ArgumentParser(
+        description="Консоль для рефлектометра"
+    )
+
+    parser.add_argument("--debug", action='store_true',
+                        help="отладочная отправка пакета soft_reset, пакета с данными и пакета start")
+
+    parser.add_argument("--ip", type=str, default="192.168.0.2",
+                        help="IP рефлектометра, по умолчанию 192.168.0.2")
+
+    parser.add_argument("--send-port", type=int, default=8080,
+                        help="Порт для отправки команд")
+
+    parser.add_argument("--recv-port", type=int,
+                        default=8080, help="Порт для приема данных")
+
+    parser.add_argument("--dac-bits", type=int, default=12,
+                        help="Битность ЦАП (влияет на максимальный pulse_height)")
+
+    # передача параметров через аргументы
+    for arg in ("pulse_width", "pulse_period", "pulse_num", "pulse_height"):
+        parser.add_argument(f"--{arg}", type=int,
+                            default=0, help=f"Задать {arg}")
+
+    args = parser.parse_args()
+
+    sock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
+
+    if args.debug:
+        run_debug(args, sock)
+    else:
+        verify_args(args)
+        run(args, sock)
+
+    sock.close()
+
+
+if __name__ == "__main__":
+    main()