322 lines
11 KiB
Systemverilog
322 lines
11 KiB
Systemverilog
module out_axis_fifo #(
|
|
parameter ACCUM_WIDTH = 32,
|
|
parameter WINDOW_SIZE = 65,
|
|
parameter PACKET_SIZE = 1024
|
|
) (
|
|
input logic eth_clk_in,
|
|
input logic acc_clk_in,
|
|
input logic rst,
|
|
input logic [31:0] smp_num,
|
|
|
|
// AXI stream master for output, eth_clk_in domain
|
|
output logic [7:0] s_axis_tdata,
|
|
output logic s_axis_tvalid,
|
|
input logic s_axis_tready,
|
|
output logic s_axis_tlast,
|
|
// eth handshake
|
|
input logic req_ready,
|
|
output logic send_req,
|
|
output logic [15:0] udp_data_length,
|
|
|
|
// data from acc
|
|
input logic [ACCUM_WIDTH-1:0] acc_din,
|
|
input logic din_valid,
|
|
|
|
// input pulse
|
|
input logic readout_begin,
|
|
|
|
// output pulses
|
|
output logic batch_req,
|
|
output logic finish
|
|
);
|
|
// sync reset
|
|
reg [1:0] rst_sync_ff;
|
|
reg rst_eth;
|
|
|
|
always @(posedge acc_clk_in or posedge rst) begin
|
|
if (rst) begin
|
|
rst_sync_ff <= 2'b11;
|
|
end else begin
|
|
rst_sync_ff <= {rst_sync_ff[0], 1'b0};
|
|
end
|
|
end
|
|
|
|
assign rst_eth = rst_sync_ff[1];
|
|
|
|
logic [1:0] rst_acc_ff;
|
|
logic rst_acc;
|
|
|
|
always_ff @(posedge acc_clk_in or posedge rst) begin
|
|
if (rst)
|
|
rst_acc_ff <= 2'b11;
|
|
else
|
|
rst_acc_ff <= {rst_acc_ff[0], 1'b0};
|
|
end
|
|
|
|
assign rst_acc = rst_acc_ff[1];
|
|
|
|
|
|
// fifo params calc
|
|
// round up to be enough for 2xPACKET_SIZE storage
|
|
localparam int MIN_BYTES = 2 * PACKET_SIZE;
|
|
localparam int MIN_BITS = MIN_BYTES * 8;
|
|
localparam int MIN_WR_WORDS = (MIN_BITS + ACCUM_WIDTH - 1) / ACCUM_WIDTH; // ceil div
|
|
localparam int WDEPTH_BITS = $clog2(MIN_WR_WORDS);
|
|
localparam int FIFO_WDEPTH = 1 << WDEPTH_BITS;
|
|
|
|
localparam int FIFO_RDEPTH = FIFO_WDEPTH * ACCUM_WIDTH / 8;
|
|
localparam int RDEPTH_BITS = $clog2(FIFO_RDEPTH) + 1;
|
|
|
|
wire wr_unavail;
|
|
wire wr_rst_busy;
|
|
reg rd_en;
|
|
|
|
|
|
typedef enum logic [2:0] {
|
|
WR_IDLE = 3'd0,
|
|
WR_CHECK = 3'd1,
|
|
WR_RUN = 3'd2,
|
|
WR_END = 3'd3
|
|
} wr_state_t;
|
|
|
|
(* MARK_DEBUG="true" *) wr_state_t wr_state;
|
|
|
|
// Write FSM
|
|
reg [31:0] wr_cnt; // current BIT mem ptr
|
|
reg [31:0] wr_batch_tgt; // next 'target' that should be written from batch
|
|
reg [31:0] wr_total; // total BITS to be sent!
|
|
|
|
wire [WDEPTH_BITS:0] wr_data_count;
|
|
|
|
// NOTE:
|
|
// each written "acc_din" ACCUM_WIDTH word
|
|
// is counted as WINDOWS_SIZE samples actually
|
|
// because hw division for counters is painful
|
|
// so we just increased the counter sizes
|
|
|
|
always_ff @(posedge acc_clk_in) begin
|
|
if (rst_acc) begin
|
|
wr_state <= WR_IDLE;
|
|
wr_cnt <= 32'b0;
|
|
wr_batch_tgt <= 32'b0;
|
|
wr_total <= 32'b0;
|
|
batch_req <= 0;
|
|
finish <= 0;
|
|
|
|
end else begin
|
|
|
|
case (wr_state)
|
|
// wait until readout is requested
|
|
WR_IDLE: begin
|
|
if (readout_begin) begin
|
|
wr_cnt <= 32'b0;
|
|
wr_state <= WR_CHECK;
|
|
wr_total <= smp_num * ACCUM_WIDTH;
|
|
wr_batch_tgt <= 32'b0;
|
|
batch_req <= 0;
|
|
finish <= 0;
|
|
end
|
|
end
|
|
|
|
// wait until we can request a word
|
|
// depends on prog_full signal
|
|
WR_CHECK: begin
|
|
if (~wr_unavail && ~wr_rst_busy) begin
|
|
batch_req <= 1;
|
|
// should give us exactly PACKET_SIZE * 8 bits
|
|
// multiplied by WINDOW_SIZE, because we count
|
|
// each given ACCUM_WIDTH word as WINDOWS_SIZE samples !!!
|
|
wr_batch_tgt <= wr_batch_tgt + (8 * WINDOW_SIZE * PACKET_SIZE);
|
|
wr_state <= WR_RUN;
|
|
end else begin
|
|
batch_req <= 0;
|
|
end
|
|
end
|
|
|
|
// wait until all requested packet is written
|
|
WR_RUN: begin
|
|
batch_req <= 0;
|
|
if (wr_cnt == wr_batch_tgt) begin
|
|
// got enough words
|
|
wr_state <= WR_END;
|
|
end else if (wr_cnt > wr_batch_tgt) begin
|
|
// weird case when accum gave us too much words
|
|
// block resets
|
|
wr_cnt <= 32'hffffffff; // sort of signal for sim/ila
|
|
wr_state <= WR_END;
|
|
end
|
|
|
|
if (din_valid) begin
|
|
// data supplied
|
|
// count as we got WINDOW_SIZE samples
|
|
wr_cnt <= wr_cnt + ACCUM_WIDTH * WINDOW_SIZE;
|
|
end
|
|
end
|
|
|
|
// check if this was last data batch
|
|
WR_END: begin
|
|
// here we check that we sent enough data
|
|
// wr_cnt should be by design PACKET_SIZE-aligned
|
|
if (wr_cnt >= wr_total) begin
|
|
// wait until all data is sent
|
|
if (wr_data_count == 0) begin
|
|
finish <= 1;
|
|
wr_state <= WR_IDLE;
|
|
end
|
|
end else begin
|
|
// next word
|
|
wr_state <= WR_CHECK;
|
|
end
|
|
end
|
|
endcase
|
|
end
|
|
end
|
|
|
|
// Readout FSM with ethernet request
|
|
|
|
assign udp_data_length = PACKET_SIZE; // fixed packet size
|
|
reg [15:0] sent_cnt;
|
|
|
|
typedef enum logic [2:0] {
|
|
RD_IDLE = 3'd0,
|
|
RD_CHECK = 3'd1,
|
|
RD_SEND = 3'd2
|
|
} rd_state_t;
|
|
|
|
(* MARK_DEBUG="true" *) rd_state_t rd_state;
|
|
|
|
wire rd_valid;
|
|
wire [RDEPTH_BITS-1:0] rd_data_count;
|
|
|
|
always_ff @(posedge eth_clk_in) begin
|
|
if (rst_eth) begin
|
|
rd_state <= RD_IDLE;
|
|
send_req <= 1'b0;
|
|
sent_cnt <= 16'd0;
|
|
s_axis_tlast <= 1'b0;
|
|
s_axis_tvalid <= 1'b0;
|
|
rd_en <= 1'b0;
|
|
|
|
end else begin
|
|
|
|
case (rd_state)
|
|
// wait until fifo has enough data to send
|
|
RD_IDLE: begin
|
|
if (rd_data_count == PACKET_SIZE) begin
|
|
// enough data to send packet, begin
|
|
rd_state <= RD_CHECK;
|
|
end
|
|
send_req <= 1'b0;
|
|
sent_cnt <= 16'd0;
|
|
rd_en <= 1'b0;
|
|
s_axis_tlast <= 1'b0;
|
|
s_axis_tvalid <= 1'b0;
|
|
end
|
|
|
|
// await udp ready
|
|
RD_CHECK: begin
|
|
if (req_ready) begin
|
|
send_req <= 1'b1;
|
|
rd_state <= RD_SEND;
|
|
end
|
|
end
|
|
|
|
// send data
|
|
RD_SEND: begin
|
|
// udp is ready and fifo is ready = sent
|
|
send_req <= 1'b0;
|
|
if (s_axis_tready && rd_valid) begin
|
|
rd_en <= 1'b1;
|
|
s_axis_tvalid <= 1'b1;
|
|
sent_cnt <= sent_cnt + 1;
|
|
// final packet of the batch
|
|
if (sent_cnt == PACKET_SIZE - 1) begin
|
|
rd_state <= RD_IDLE;
|
|
s_axis_tlast <= 1'b1;
|
|
end
|
|
end else begin
|
|
rd_en <= 1'b0;
|
|
s_axis_tvalid <= 1'b0;
|
|
end
|
|
end
|
|
endcase
|
|
end
|
|
end
|
|
|
|
logic [ACCUM_WIDTH-1:0] fifo_din_r, acc_din_reg, din_valid_reg;
|
|
logic fifo_wr_en_r;
|
|
|
|
always_ff @(posedge acc_clk_in) begin
|
|
if (rst_acc) begin
|
|
fifo_din_r <= '0;
|
|
fifo_wr_en_r <= 1'b0;
|
|
|
|
din_valid_reg <= 1'b0;
|
|
end else begin
|
|
fifo_wr_en_r <= 1'b0;
|
|
acc_din_reg <= acc_din;
|
|
|
|
if (!wr_rst_busy && din_valid_reg) begin
|
|
fifo_din_r <= acc_din_reg;
|
|
fifo_wr_en_r <= 1'b1;
|
|
end
|
|
|
|
din_valid_reg <= din_valid;
|
|
end
|
|
end
|
|
|
|
// xpm_fifo_async: Asynchronous FIFO
|
|
// Xilinx Parameterized Macro, version 2025.1
|
|
|
|
xpm_fifo_async #(
|
|
.DOUT_RESET_VALUE("0"), // String
|
|
.FIFO_READ_LATENCY(1), // DECIMAL
|
|
.FIFO_WRITE_DEPTH(FIFO_WDEPTH),
|
|
.FULL_RESET_VALUE(0),
|
|
.PROG_EMPTY_THRESH(PACKET_SIZE),
|
|
.PROG_FULL_THRESH(PACKET_SIZE / (ACCUM_WIDTH / 8)),
|
|
.RD_DATA_COUNT_WIDTH(RDEPTH_BITS),
|
|
.READ_DATA_WIDTH(8), // always 8 bit for eth
|
|
.READ_MODE("fwft"),
|
|
.SIM_ASSERT_CHK(1), // DECIMAL; 0=disable simulation messages, 1=enable simulation messages
|
|
.USE_ADV_FEATURES("1616"), // String
|
|
.WRITE_DATA_WIDTH(ACCUM_WIDTH),
|
|
.WR_DATA_COUNT_WIDTH(WDEPTH_BITS+1)
|
|
)
|
|
xpm_fifo_async_inst (
|
|
|
|
.data_valid(rd_valid), // 1-bit output: Read Data Valid: When asserted, this signal indicates that valid data is available on the
|
|
// output bus (dout).
|
|
|
|
.dout(s_axis_tdata),
|
|
.empty( ),
|
|
|
|
.full( ),
|
|
|
|
.prog_full(wr_unavail), // 1-bit output: Programmable Full: This signal is asserted when the number of words in the FIFO is greater than
|
|
// or equal to the programmable full threshold value. It is de-asserted when the number of words in the FIFO is
|
|
// less than the programmable full threshold value.
|
|
|
|
.rd_data_count(rd_data_count), // RD_DATA_COUNT_WIDTH-bit output: Read Data Count: This bus indicates the number of words read from the FIFO.
|
|
|
|
.wr_data_count(wr_data_count), // WR_DATA_COUNT_WIDTH-bit output: Write Data Count: This bus indicates the number of words written into the
|
|
// FIFO.
|
|
|
|
|
|
|
|
|
|
.rd_clk(eth_clk_in), // 1-bit input: Read clock: Used for read operation. rd_clk must be a free running clock.
|
|
.rd_en(rd_en), // 1-bit input: Read Enable: If the FIFO is not empty, asserting this signal causes data (on dout) to be read
|
|
// from the FIFO. Must be held active-low when rd_rst_busy is active high.
|
|
|
|
.rst(rst),
|
|
|
|
.din(fifo_din_r), // WRITE_DATA_WIDTH-bit input: Write Data: The input data bus used when writing the FIFO.
|
|
.wr_clk(acc_clk_in), // 1-bit input: Write clock: Used for write operation. wr_clk must be a free running clock.
|
|
.wr_en(fifo_wr_en_r),
|
|
|
|
.wr_rst_busy(wr_rst_busy)
|
|
|
|
);
|
|
|
|
endmodule |